Page 1809 of 2893
(#'
)
Seat-back
20-131
Rear Seat Removal/Installation
Fastener Locations B
:Bolt,3
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
C
D E
A
B
C EFastener Location
:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) A
B
A
NOTE: Take care not to scratch the body or tear the seat
covers. 1. Remove the right seat-back (A). –1 Fold the right seat-back down.
–2 Release the Velcro fasteners (B), and pull backthe seat-back cover (C), then remove the bolts.
–3 Release the hooks (D) of the pivot bracket (E). 2. Remove the bolt, then remove the center pivot
bracket (A).
3. If necessary, remove the bushing (B).
(cont’d)
08/08/21 15:04:02 61SNR030_200_0133
ProCarManuals.com
DYNOMITE -2009-
Page 1810 of 2893
20-132Seats
Rear Seat Removal/Installation (cont’d)
Fastener Location
:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) FG
H
A B
C
D
E
B A
B
C
D
A
B
Front
4. Remove the left seat-back (A). –1 Fold the left seat-back down.
–2 Pull the rear center seat belt (B) out through theslit (C) in the seat belt guide (D).
–3 Release the Velcro fastener (E), and pull back the seat-back cover (F), then remove the bolt.
–4 Release the hooks (G) of the pivot bracket (H). 5. Extend the rear center seat belt (A) to remove the
left seat-back (B), then release the pivot shaft (C)
from the center pivot bracket (D).
6. If necessary, remove the bushing (A) from the center pivot bracket (B).
08/08/21 15:04:03 61SNR030_200_0134
ProCarManuals.com
DYNOMITE -2009-
Page 1811 of 2893
Seat Cushion
20-133
Fastener Location:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A 6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A B
Fastener Location
:Bolt,1
7. Remove the seat cushion and seat side bolster.
8. Remove the bolt, then remove the pivot bracket (A).
9. Install the seat-back in the reverse order of removal, and note these items:
Guide the belt over the front of the seat-back as you install the seat-back.
Before attaching the rear seat-back, make sure there are no twists or kinks in the rear center seat
belt. NOTE: Take care not to scratch the body or tear the seat
covers.
1. Remove the bolt between the seat-back (A) and the seat cushion (B).
(cont’d)
08/08/21 15:04:03 61SNR030_200_0135
ProCarManuals.com
DYNOMITE -2009-
Page 1812 of 2893
Î
Seat Side Bolster
20-134Seats
Rear Seat Removal/Installation (cont’d)
C
D
E
C C
F
B
A
Fastener Location
:Bolt,1
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
2. While pushing down on the seat cushion (A), pullthe seat hook handles (B) to release the hooks (C).
3. Pull back the seat cushion to release the center seat belt (D) and seat belt buckles (E) from their slits (F),
and remove it.
4. Install the seat cushion in the reverse order of removal, and note these items:
Before attaching the seat cushion, make sure there are no twists or kinks in the seat belts.
When installing the seat cushion, slip the seat belt buckles through the slits in the seat cushion. NOTE: Take care not to scratch the body or tear the seat
covers.
1. Remove the seat cushion.
2. Remove the bolt.
08/08/21 15:04:03 61SNR030_200_0136
ProCarManuals.com
DYNOMITE -2009-
Page 1813 of 2893
(#'
)
20-13520-135
Rear Seat-back Latch Replacement
A
B
B
A
B
A
B
Fastener Locations
A
:Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
3. Fold the seat-back down.
4. Lift the seat side bolster (A) up to release the hook(B), then remove the seat side bolster.
5. Install the side bolster in the reverse order of removal, and note these items:
Guide the belts over the front of the seat side bolster as you install the bolster.
Before attaching the seat side bolster, make sure there are no twists or kinks in the seat belts. NOTE: Take care not to bend or scratch the interior trim.
1. Remove the rear shelf (see page 20-78).
2. From the trunk compartment, disconnect the seat- back release cable (A) from the seat-back latch (B).
3. Remove the bolts, then remove the seat-back latch (A).
(cont’d)
08/08/21 15:04:04 61SNR030_200_0137
ProCarManuals.com
DYNOMITE -2009-
Page 1814 of 2893
(#'
)
20-13520-135
Rear Seat-back Latch Replacement
A
B
B
A
B
A
B
Fastener Locations
A
:Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
3. Fold the seat-back down.
4. Lift the seat side bolster (A) up to release the hook(B), then remove the seat side bolster.
5. Install the side bolster in the reverse order of removal, and note these items:
Guide the belts over the front of the seat side bolster as you install the bolster.
Before attaching the seat side bolster, make sure there are no twists or kinks in the seat belts. NOTE: Take care not to bend or scratch the interior trim.
1. Remove the rear shelf (see page 20-78).
2. From the trunk compartment, disconnect the seat- back release cable (A) from the seat-back latch (B).
3. Remove the bolts, then remove the seat-back latch (A).
(cont’d)
08/08/21 15:04:04 61SNR030_200_0137
ProCarManuals.com
DYNOMITE -2009-
Page 1815 of 2893
(#'
)
20-13620-136 Seats
Rear Seat-back Latch Replacement
(cont’d)
Rear Seat-back Release Lever/Cable
Removal/Installation
Fastener Location
:Clip,1
A
B
4. Install the latch in the reverse order of removal, and note these items:
Make sure the release cable is connected securely.
Make sure the seat-back locks securely and unlocks properly. NOTE: Take care not to bend or scratch the interior trim.
1. Open the trunk lid.
2. From the trunk compartment, detach the cable clip.
3. Disconnect the seat-back release cable (A) from the seat-back latch (B).
08/08/21 15:04:04 61SNR030_200_0138
ProCarManuals.com
DYNOMITE -2009-
Page 1816 of 2893
(#'
)
20-13620-136 Seats
Rear Seat-back Latch Replacement
(cont’d)
Rear Seat-back Release Lever/Cable
Removal/Installation
Fastener Location
:Clip,1
A
B
4. Install the latch in the reverse order of removal, and note these items:
Make sure the release cable is connected securely.
Make sure the seat-back locks securely and unlocks properly. NOTE: Take care not to bend or scratch the interior trim.
1. Open the trunk lid.
2. From the trunk compartment, detach the cable clip.
3. Disconnect the seat-back release cable (A) from the seat-back latch (B).
08/08/21 15:04:04 61SNR030_200_0138
ProCarManuals.com
DYNOMITE -2009-