2006 ACURA CSX wheel torque

ItemMeasurement Qualification Specification
2-21
MANUAL
TRANSMISSION
(5-speed)Type Synchronized, five-speed forward, one reverse
Primary reduction Direct 1:1
Gear ratio 1st 3.267
2nd 1.880
3rd 1.212
4th 0.921
5th 0.738
Reverse 3.583
Final reduction Type Single helical gear Gear ratio 4.839
MANUAL
TRANSMISSION
(6-speed) Type Synchronized, six-speed forward, one reverse
Primary reduction Direct 1:1
Gear ratio 1st 3.267
2nd 2.130
3rd 1.517
4th 1.147
5th 0.921
6th 0.659
Reverse 3.583
Final reduction Type Single helical gear Gear ratio 4.765
AUTOMATIC
TRANSMISSION Type Electronically-controlled automatic, five-speed forward, one
reverse three-element torque converter with lock-up clutch
Primary reduction Direct 1:1
Gear ratio 1st 2.651 2nd 1.516
3rd 1.081
4th 0.772
5th 0.566
Reverse 2.000
Final reduction Type Single helical gear Gear ratio 4.562
STEERING Type Electrical power-assisted rack and pinion Overall ratio 13.62
Turns, lock-to-lock 2.65
Steering wheel diameter 360 mm (14.2 in.)
SUSPENSION Type Front Independent strut with stabilizer, coil spring Rear Independent double wishbone with stabilizer, coil spring
Shock absorber Front and rear Telescopic, hydraulic, nitrogen gas-filled
TIRES Size of front and rear tires (’06-08 models) Except TYPE S P205/55R16 89H
TYPE S P215/45R17 87V
Size of front and rear tires
(’09 model) P215/45R17 87V
Size of spare tire (’06-07 models) Except TYPE S T125/70D15 95M TYPE S T135/80R16 101M
Size of spare tire (’08-09 models) T135/80R16 101M
(cont’d)
08/08/21 14:07:26 61SNR030_020_0021
ProCarManuals.com
DYNOMITE -2009-

Ì
Ï
µ
µ
Î
(#')
µ
µ µ
µ
µ
µ
Special Tools Required
YES
NO YES
NO
YES
NO
4-6Starting System
Starter System Circuit Troubleshooting
OTC3131
Alternator, Regulator, Battery & Starter tester OTC3131
Available through the Honda Canada Inc. Technical
Tools Department; FAX
866-398-8665/e-mail:
ch_technicaltools ch.honda.com
NOTE:  Air temperature must be within 15 38 °C (59 100 °F) during this procedure.
 After this inspection, you must reset the engine control module (ECM)/powertrain control module
(PCM). Otherwise, the ECM/PCM will continue to stop
the fuel injectors from operating.
 The battery must be in good condition and fully charged.
1. Connect the alternator, regulator, battery & starter tester (OTC3131) to the battery as shown.
NOTE: The probe is not used for battery testing.
2. Do the BATTERY TEST. ThebatteryisOK.Gotostep3.
If the display indicates BAD BATTERY, replace
the battery, then retest. If the display indicates
CHARGE & RETEST, charge the battery, then retest. 3. Connect the Honda Diagnostic System (HDS) to the
data link connector (DLC) (see step 2 on page 11-3).
4. Turn the ignition switch to ON (II).
5. Make sure the HDS communicates with the vehicle and the ECM/PCM. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
6. Select ALL INJECTORS STOP in the PGM-FI INSPECTION menu with the HDS.
7. Set the parking brake, then with the shift lever in N or P (A/T model) or the clutch pedal pressed (M/T
model), turn the ignition switch to START (III).
The starting system is OK. Go to step 14.
Go to step 8.
8. Turn the ignition switch to LOCK (0).
9. Check the electrical connections at the battery, the negative battery cable to the body, the engine
ground cables, and the starter for looseness and
corrosion. Then try cranking the engine again.
Repairing the loose connection corrected the
problem. The starting system is OK. Go to step 14.
Based on the following symptoms, take the
appropriate action:
 If the starter does not crank the engine at all, go to step 10.
 If the starter cranks the engine erratically or too slowly,gotostep12.
 If the starter does not disengage from the flywheel ring gear (M/T model) or torque
converter ring gear (A/T model) when you
release the key, replace the starter, or remove
and disassemble it, and check for the following:
– Starter solenoid and switch malfunction
– Dirty drive gear or damaged overrunning clutch
Does the display indicate GOOD or GOOD, LOWCHARGE? Does t he st ar t er cr ank t he engi ne nor mal l y ?
Does t he st ar t er cr ank t he engi ne nor mal l y ?
08/08/21 14:09:22 61SNR030_040_0007
ProCarManuals.com
DYNOMITE -2009-

Î

(#'

)
µ
µ
YES
NO
M/T model
4-84-8 Starting System
Starter System Circuit
Troubleshooting (cont’d)
Clutch Interlock Switch Test
OTC3131 A
B
Terminal
Position
Clutch Interlock Switch
Clutch Interlock Switch 2
1
(PRESSED)
(RELEASED)
12. Do the STARTING TEST with the alternator, regulator battery & starter tester.
NOTE: The probe is used for starter testing.
Go to step 13.
Replace the starter, or remove and
disassemble it, and check for these problems:
 Draginthestarterarmature
 Short in the armature winding
 Excessive drag in the engine
 Open circuit in starter armature commutator segments
 Excessively worn starter brushes
 Open circuit in the starter brushes
 Dirty or damaged helical splines or drive gear
 Faulty overrunning clutch
13. Remove the starter, and inspect its drive gear and the flywheel ring gear (M/T model) or the torque
converter ring gear (A/T model) for damage.
Replace any damaged parts.
14. Select ECM/PCM reset (see page 11-4) in the PGM- FI INSPECTION menu to cancel ALL INJECTORS
STOP with the HDS. 1. Disconnect the clutch interlock switch 2P connector
(A).
2. Remove the clutch interlock switch (B).
3. Check for continuity between the terminals accordingtothetable.
 If the continuity is not as specified, replace the clutch interlock switch (see page 12-8).
 If OK, install the clutch interlock switch, and adjust the pedal height (see page 12-8).
Terminal side of
male terminals
Does the display indicate cranking voltage greatert han or equal t o 8.5 V and t he cur r ent d r aw l esst han or equal t o 380 A?
08/08/21 14:09:23 61SNR030_040_0009
ProCarManuals.com
DYNOMITE -2009-

Ì
Ì




Overrunning Clutch Inspection Starter Reassembly
4-17
B
A A
B CD
E
F
14. While holding the drive gear (A), turn the gear shaft (B) counterclockwise. Check that the drive
gear comes out to the other end. If the drive gear
does not move smoothly, replace the gear cover
assembly.
15. While holding the drive gear, turn the gear shaft clockwise. The gear shaft should turn freely. If the
gear shaft does not turn freely, replace the gear
cover assembly.
16. If the drive gear is worn or damaged, replace the overrunning clutch assembly; the gear is not
available separately.
Check the condition of the flywheel ring gear (M/T
model), or the torque converter ring gear (A/T
model) to see if the starter drive gear teeth are
damaged. 17. Install the brush into the brush holder, and set the
armature (A) in the brush holder (B).
NOTE: To seat the new brushes, slip a strip of 500
or 600 sandpaper, with the grit side up, between
the commutator and each brush, and smoothly turn
the armature. The contact surface of the brushes
will be sanded to the same contour as the
commutator.
18. While squeezing a spring (C), insert it in the hole on the brush holder, and push it until it bottoms.
Repeat this for the other three springs (D, E, and F).
19. Install the armature and the brush holder assembly into the housing.
NOTE: Make sure the armature stays in the holder.
08/08/21 14:09:28 61SNR030_040_0018
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-


Î
Installation
6-17
A
B
D
C : Lubricate with the new engine oil
: Clean
A
07JAB-001020A B
07NAB-001040A
C
07JAA-001020A
(or commercially
available) 90 °
A
B
1. Clean the crankshaft pulley (A), crankshaft (B), bolt(C), and washer (D). Lubricate with new engine oil
as shown.
2. Install the crankshaft pulley, and hold the pulley with the holder handle (A) and holder attachment
(B). 3. Tighten the bolt to 49 N·m (5.0 kgf·m, 36 lbf·ft) with
a torque wrench and the socket, 19 mm (C). Do not
use an impact wrench. If the pulley bolt or
crankshaft are new, tighten the bolt to 177 N·m
(18.0 kgf·m, 130 lbf·ft), then remove the bolt and
tighten it to 49 N·m (5.0 kgf·m, 36 lbf·ft).
4. Mark the bolt head (A) and the crankshaft pulley (B) as shown, then tighten the bolt an additional 90 °
(The mark on the bolt head line up with the mark on
the crankshaft pulley).
5. Install the drive belt (see page 4-31).
6. Install the splash shield (see step 40 on page 5-20).
7. Install the right front wheels.
08/08/21 14:26:33 61SNR030_060_0017
ProCarManuals.com
DYNOMITE -2009-


Î


(#'
 )
 M/T model
A/T model
6-18
Cylinder Head
Cam Chain Removal
C
A
B
B
A
C A
A
NOTE: Keep the cam chain away from magnetic fields. 1. Remove the front wheels.
2. Remove the splash shield (see step 25 on page 5-5).
3. Remove the drive belt (see page 4-31).
4. Remove the cylinder head cover (see page 6-36).
5. Set the No. 1 piston at top dead center (TDC). The punch mark (A) on the variable valve timing control
(VTC) actuator and the punch mark (B) on the
exhaust camshaft sprocket should be at the top.
Align the TDC marks (C) on the VTC actuator and
the exhaust camshaft sprocket.
6. Disconnect the crankshaft position (CKP) sensor connector (A) and the VTC oil control solenoid
valve connector (B), and remove the harness
clamps (C). 7. Remove the VTC oil control solenoid valve
(see page 11-294).
8. Remove the crankshaft pulley (see page 6-16).
9. Support the engine with a jack and a wood block under the oil pan.
10. Remove the upper torque rod (A).
08/08/21 14:26:33 61SNR030_060_0018
ProCarManuals.com
DYNOMITE -2009-