Page 81 of 2893

(#'
)
µµ µ
Auto-tensioner Spring Torque:
32.5 39.7 N·m (3.31 4.05 kgf·m, 23.9 29.3 lbf·ft)
4-324-32 Charging System
Drive Belt Auto-tensioner
Inspection (cont’d)
Drive Belt Auto-tensioner Removal/
Installation
A
B
C
E
F
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) 6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
10x1.25mm
56 N·m (5.7 kgf·m, 41 lbf·ft) B
30 °
30 °
D
6. Remove the auto-tensioner (see page 4-32).
7. Clamp the auto-tensioner (A) by using two 8 mmbolts (B) and a vise (C) as shown. Do not clamp the
auto-tensioner itself.
8. Set the torque wrench (D) on the pulley bolt, and align it as shown.
9. Align the indicator’s pointer (E) on the tensioner base with center mark (F) on the tensioner arm by
using the torque wrench, and measure the torque.
If the torque value is out of specification, replace
the auto-tensioner.
NOTE: If the indicator exceeds the center mark,
recheck the torque. 1. Remove the drive belt (see page 4-31).
2. Remove the idler pulley base.
3. Remove the pulley bolt (A), then remove the
tensioner pulley (B).
08/08/21 14:10:13 61SNR030_040_0033
ProCarManuals.com
DYNOMITE -2009-
Page 82 of 2893
(#'
)
4-334-33
Tensioner Pulley Replacement
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) A
10x1.25mm
56 N·m
(5.7 kgf·m, 41 lbf·ft)B
4. Remove the auto-tensioner.
5. Install the auto-tensioner in the reverse order of
removal. 1. Remove the drive belt (see page 4-31).
2. Remove the pulley bolt (A), then remove the
tensioner pulley (B).
3. Install the tensioner pulley in the reverse order of removal.
08/08/21 14:10:14 61SNR030_040_0034
ProCarManuals.com
DYNOMITE -2009-
Page 83 of 2893
(#'
)
(#'
)
Removal
4-344-34 Charging System
Idler Pulley Replacement
Alternator Removal and Installation
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
AB
C
A
C
C C
1. Remove the drive belt (see page 4-31).
2. Remove the idler pulley.
3. Install the idler pulley in the reverse order of
removal. 1. Do the battery terminal disconnection procedure
(see page 22-68).
2. Remove the drive belt (see page 4-31).
3. Remove the front grille cover (see page 20-163).
4. Disconnect the fan motor connectors (A) and the hood switch connector (B), then remove the
harnessclamps(C).
08/08/21 14:10:14 61SNR030_040_0035
ProCarManuals.com
DYNOMITE -2009-
Page 84 of 2893
Î
Î
4-35
D
C
A
C B
B
C
A AB
C
5. Disconnect the reservoir hose (A), and remove the radiator cap base mounting bolts (B), the radiator
upper brackets (C) and the bolts (D).
6. Remove the A/C condenser bracket mounting bolts (A) and the bulkhead mounting bolts (B), then
remove the bulkhead (C). 7. Remove the three bolts securing the alternator.
8. Disconnect the alternator connector (A), and the
positive alternator cable (B) and remove the
harness clamp (C), then remove the alternator.
(cont’d)
08/08/21 14:10:15 61SNR030_040_0036
ProCarManuals.com
DYNOMITE -2009-
Page 85 of 2893

Î Î
Î
Installation
4-36Charging System
Alternator Removal and Installation (cont’d)
A
B
C 6x1.0mm
8 N·m (0.8 kgf·m,
6lbf·ft)
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) 8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) A
B
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft)
C
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft) A
D
A
C
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft)
1. Install the alternator, then connect the alternator
connector (A) and the positive alternator cable (B)
and install the harness clamp (C). Make sure the
crimped side of the ring terminal faces away from
the alternator when you connect it.
2. Tighten the three bolts securing the alternator. 3. Install the bulkhead (A), then install the bulkhead
mounting bolts (B) and the A/C condenser bracket
mounting bolts (C).
4. Apply body paint to the bulkhead mounting bolts.
5. Install the radiator upper brackets (A), the radiator cap base mounting bolts (B), and the bolts (C), and
connect the reservoir hose (D).
08/08/21 14:10:16 61SNR030_040_0037
ProCarManuals.com
DYNOMITE -2009-
Page 86 of 2893
4-37
AB
C
A
C
C C
6. Connect the fan motor connectors (A) and the hood
switch connector (B), then install the harness
clamps (C).
7. Install the front grille cover (see page 20-163).
8. Install the drive belt (see page 4-31).
9. Do the battery terminal reconnecting procedure (see page 22-68).
08/08/21 14:10:16 61SNR030_040_0038
ProCarManuals.com
DYNOMITE -2009-
Page 87 of 2893
Î
(#'
!)
Exploded View
4-38Charging System
Alternator Overhaul
ROTOR
FRONT BEARING
RETAINERFRONT BEARING
DRIVE-END
HOUSING
PULLEYPULLEY
LOCKNUT
TERMINAL
INSULATOR BRUSH HOLDER
ASSEMBLY REAR HOUSING
ASSEMBLY
END COVER WASHER
08/08/21 14:10:17 61SNR030_040_0039
ProCarManuals.com
DYNOMITE -2009-
Page 88 of 2893
Special Tools Required
4-39
B
A
Driver 07749-0010000
Attachment, 42 x 47 mm 07746-0010300
NOTE: Refer to the Exploded View as needed during
this procedure.1. Test the alternator and regulator before you remove them (see page 4-28).
2. Remove the alternator (see page 4-34).
3. If the front bearing needs replacing, remove the pulley locknut with a 10 mm wrench (A) and a
22 mm wrench (B). If necessary, use an impact
wrench.
4. Remove the harness stay and the three flange nuts from the alternator. 5. Remove the end cover.
6. Remove the brush holder assembly.
(cont’d)
08/08/21 14:10:18 61SNR030_040_0040
ProCarManuals.com
DYNOMITE -2009-