2006 ACURA CSX Oil pan

Î
 Î

5-23
B
A
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
B A
B
C
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
56. Install the ECM/PCM (A), then install the ECM/PCM
cover (B).
57. Connect the battery cables (A) to the under-hood fuse/relay box.
58. Install the harness clamp (B). 59. Install the pipe (A).
60. Connect the connector (B), and install the harness
clamps (C).
61. Install the under cowl-panel (see step 4 on page 20-164).
62. Install the air cleaner assembly (see page 11-345).
63. Install the front wheels.
64. Do the battery installation procedure (see page 22-69).
65. Inspect for fuel leaks. Turn the ignition switch to ON (II) (do not operate the starter) so the fuel pump
runs for about 2 seconds and pressurizes the fuel
line. Repeat this operation three times, then check
for fuel leakage at any point in the fuel line.
66. Refill the engine with engine oil (see step 4 on page 8-10).
(cont’d)
08/08/21 14:21:01 61SNR030_050_0023
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-



(#'
 ) M/T model
A/T model
5-355-35
Side Engine Mount Bracket
Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
7. Raise the vehicle on the lift.
8. M/T model: Tighten the front mount mounting bolt.
9. Install the splash shield (see step 40 on page 5-20).
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
(cont’d)
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:08 61SNR030_050_0035
ProCarManuals.com
DYNOMITE -2009-



(#'
 ) M/T model
A/T model
5-355-35
Side Engine Mount Bracket
Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
7. Raise the vehicle on the lift.
8. M/T model: Tighten the front mount mounting bolt.
9. Install the splash shield (see step 40 on page 5-20).
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
(cont’d)
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:08 61SNR030_050_0035
ProCarManuals.com
DYNOMITE -2009-


Î


(#'
 )
 M/T model
A/T model
6-18
Cylinder Head
Cam Chain Removal
C
A
B
B
A
C A
A
NOTE: Keep the cam chain away from magnetic fields. 1. Remove the front wheels.
2. Remove the splash shield (see step 25 on page 5-5).
3. Remove the drive belt (see page 4-31).
4. Remove the cylinder head cover (see page 6-36).
5. Set the No. 1 piston at top dead center (TDC). The punch mark (A) on the variable valve timing control
(VTC) actuator and the punch mark (B) on the
exhaust camshaft sprocket should be at the top.
Align the TDC marks (C) on the VTC actuator and
the exhaust camshaft sprocket.
6. Disconnect the crankshaft position (CKP) sensor connector (A) and the VTC oil control solenoid
valve connector (B), and remove the harness
clamps (C). 7. Remove the VTC oil control solenoid valve
(see page 11-294).
8. Remove the crankshaft pulley (see page 6-16).
9. Support the engine with a jack and a wood block under the oil pan.
10. Remove the upper torque rod (A).
08/08/21 14:26:33 61SNR030_060_0018
ProCarManuals.com
DYNOMITE -2009-






6-24
Cylinder Head
Cam Chain Installation (cont’d)
A
B
B
A
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A B
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) D B
C
16. Clean, and dry the chain case mating surfaces.
17. Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, or 08718-0009, evenly to the engine
block mating surface of the chain case, and to the
inside edge of the threaded bolt holes. Install the
component within 5 minutes of applying the liquid
gasket.
NOTE: If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket.
18. Apply liquid gasket to the engine block upper surface contact areas (A) on the chain case and
lower block upper surface contact areas (B) on the
chain case.
19. Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, or 08718-0009, evenly to the oil pan
mating surface of the chain case, and to the inside
edge of the threaded bolt holes. Install the
component within 5 minutes of applying the liquid
gasket.
NOTE: If you apply liquid gasket P/N 08718-0012, the component must be install within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket. 20. Install the new O-ring (A) on the chain case. Set the
edge of the chain case (B) to the edge of the oil pan
(C), then install the chain case on the engine block
(D). Wipe off the excess liquid gasket on the oil pan
and chain case mating surface.
NOTE: When installing the chain case, do not slide the bottom surface onto the oil pan mounting surface.
 Wait at least 30 minutes before filling the engine with oil.
 Do not run the engine for at least 3 hours after installing the chain case.
Apply liquid gasket
along the broken line.
Apply liquid gasket
along the broken line.
08/08/21 14:27:19 61SNR030_060_0024
ProCarManuals.com
DYNOMITE -2009-


(#'
") Tensioner Rod Length
Service Limit: 13.5 mm (0.53 in.)
6-32
Cylinder Head
Cam Chain Inspection
13.5 mm (0.53 in.)
1. Remove the right front wheels.
2. Remove the splash shield (see step 25 on page 5-5).
3. Remove the drive belt (see page 4-31).
4. Remove the cylinder head cover (see page 6-36).
5. Set the No. 1 piston at top dead center (TDC). The
punch mark on the variable valve timing control
(VTC) actuator and the punch mark on the exhaust
camshaft sprocket should be at the top. Align the
TDC marks on the VTC actuator and the exhaust
camshaft sprocket (see step 5 on page 6-18).
6. Disconnect the crankshaft position (CKP) sensor connector and the VTC oil control solenoid valve
connector, and remove the harness clamps (see
step 6 on page 6-18).
7. Remove the VTC oil control solenoid valve (see page 11-294).
8. Remove the crankshaft pulley (see page 6-16).
9. Support the engine with a jack and a wood block under the oil pan.
10. Remove the upper torque rod (see step 10 on page 6-18).
11. Remove the ground cable, then remove the side engine mount bracket (see step 11 on page 6-19).
12. Remove the side engine mount bracket (see step 12 on page 6-19).
13. Remove the cam chain case (see step 13 on page 6-19). 14. Measure the tensioner rod length between the
tensioner body and bottom of the flat surface
section on the tensioner rod. If the length is more
than the service limit, replace the cam chain and
the oil pump chain.
15. Check the chain case oil seal for damage. If the oil seal is damaged, replace the chain case oil seal
(see page 6-31).
16. Remove all of the old liquid gasket from the chain case mating surfaces, bolt and bolt holes.
17. Clean, and dry the chain case mating surfaces.
18. Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, or 08718-0009, evenly to the engine
block mating surface of the chain case, and to the
inside edge of the threaded bolt holes. Install the
component within 5 minutes of applying the liquid
gasket(seestep17onpage6-24).
NOTE: If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket.
19. Apply liquid gasket to the engine block upper surface contact areas on the chain case and lower
block upper surface contact areas on the chain case
(see step 18 on page 6-24).
08/08/21 14:27:24 61SNR030_060_0032
ProCarManuals.com
DYNOMITE -2009-