Page 3513 of 3833
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-23
C
D
E
F
G
H
I
J
L
MA
B
LT
Removal and Installation for Side Turn Signal LampEKS003BI
1. Push the side turn signal lamp toward A direction in the figure,
and pull up B direction in the figure.
2. Disconnect the side turn signal lamp connector.
Removal and Installation for Rear Turn Signal LampEKS003BJ
Refer toLT-42, "REAR COMBINATION LAMP"
PKIA0469E
Page 3514 of 3833
LT-24
LIGHTING AND TURN SIGNAL SWITCH
LIGHTING AND TURN SIGNAL SWITCH
PFP:25540
Removal and InstallationEKS0034F
1. Remove the steering column cover. Refer to PS-9, "STEERING
COLUMN" in “POWER STEERING SYSTEM (PS)” section.
2. Remove lighting and turn signal switch fixing pawls and remove
the lighting and turn signal switch from the spiral cable.
3. Disconnect the lighting and turn signal switch connector.
Switch Circuit InspectionEKS0034G
Using circuit tester, check continuity between the lighting and turn signal switch connector terminals in each
operation status of the switch.
Lighting switch is refer toLT- 5 , "
Wiring Diagram — H/LAMP —"
Turn signal lamp switch is refer toLT-19, "Wiring Diagram — TURN —"
Front fog lamp switch is refer toLT-34, "Wiring Diagram — F/FOG —"
Rear fog lamp switch is refer toLT- 3 7 , "Wiring Diagram -R/FOG-/Without Front Fog Lamp" ,LT-38, "Wiring Dia-
gram -R/FOG-/With Front Fog Lamp"
SKIA4168E
Page 3515 of 3833
HAZARD SWITCH
LT-25
C
D
E
F
G
H
I
J
L
MA
B
LT
HAZARD SWITCHPFP:25290
Removal and Installation EKS003BZ
REMOVAL
1. Remove Instrument lower center panel. Refer to IP-3, "INSTRU-
MENT PANEL ASSEMBLY" .in “INSTRUMENT PANEL (IP)”
section.
2. Using a flat-bladed screwdriver or other suitable tool, press pawl
to remove hazard switch from Instrument lower center panel.
INSTALLATION
Installation is in the reverse order of removal.
SKIA0061E
Page 3516 of 3833
LT-26
STOP LAMP
STOP LAMP
PFP:26550
Wiring Diagram — STOP/L —EKS0034I
TKWA0067E
Page 3517 of 3833
STOP LAMP
LT-27
C
D
E
F
G
H
I
J
L
MA
B
LT
Bulb ReplacementEKS0034K
STOP LAMP
Refer to LT- 4 2 , "REAR COMBINATION LAMP"
HIGH-MOUNTED STOP LAMP
1. Remove the high-mounted stop lamp cover. Refer toLT- 2 7 ,
"HIGH-MOUNTED STOP LAMP" .
2. Turn the high-mounted stop lamp bulb socket counterclockwise
and unlock it.
3. Remove the bulb.
Removal and InstallationEKS0034L
STOP LAMP
Refer toLT-42, "REAR COMBINATION LAMP"
HIGH-MOUNTED STOP LAMP
1. Pull the edge of the cover (A in the figure below) to each side in
turn downward until the pawls inside the cover are released.
2. Pull down the cover toward under the vehicle.
3. Remove the high-mounted stop lamp mounting bolts.
4. Disconnect the high-mounted stop lamp connector and remove
from the vehicle.High-mounted Stop Lamp : 12V 5W
PKIA0496E
PKIA0497E
PKIA0498E
Page 3518 of 3833
LT-28
BACK-UP LAMP
BACK-UP LAMP
PFP:26550
Wiring Diagram — BACK/L — EKS003C3
TKWA0068E
Page 3519 of 3833
BACK-UP LAMP
LT-29
C
D
E
F
G
H
I
J
L
MA
B
LT
Bulb Replacement EKS003C4
Refer to LT- 4 2 , "REAR COMBINATION LAMP" .
Removal and Installation EKS003C5
Refer to LT- 4 2 , "REAR COMBINATION LAMP" .
Page 3520 of 3833
LT-30
PARKING, LICENSE PLATE AND TAIL LAMPS
PARKING, LICENSE PLATE AND TAIL LAMPS
PFP:26550
Wiring Diagram — TAIL/L — EKS003C0
TKWA0065E
SMA for models with roof
mounted driving lamp