2001 NISSAN X-TRAIL Service Repair Manual

radio antenna height power steering fluid bolt pattern climate settings night vision

Load previous 8 pages

Page 1305 of 3833

NISSAN X-TRAIL 2001 Service Repair Manual DTC P0327, P0328 KS
EC-955
[QR20(WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
4.RETIGHTEN GROUND SCREWS
Loosen and retighten engine ground screws.
>> GO TO 5.
5.CHECK INTERMITTENT INCIDENT
Refer to EC-84

Page 1306 of 3833

NISSAN X-TRAIL 2001 Service Repair Manual EC-956
[QR20(WITH EURO-OBD)]
DTC P0335 CKP SENSOR (POS)
DTC P0335 CKP SENSOR (POS)
PFP:23731
Component DescriptionEBS00MX8
The crankshaft position sensor (POS) is located on the cylinder
bloc

Page 1307 of 3833

NISSAN X-TRAIL 2001 Service Repair Manual DTC P0335 CKP SENSOR (POS)
EC-957
[QR20(WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
On Board Diagnosis LogicEBS00MXB
DTC Confirmation ProcedureEBS00MXC
NOTE:
If “DTC Confirmation Procedure” has been

Page 1308 of 3833

NISSAN X-TRAIL 2001 Service Repair Manual EC-958
[QR20(WITH EURO-OBD)]
DTC P0335 CKP SENSOR (POS)
Wiring Diagram
EBS00MXD
TBWA0065E
SMA for models with roof mounted driving lamp

Page 1309 of 3833

NISSAN X-TRAIL 2001 Service Repair Manual DTC P0335 CKP SENSOR (POS)
EC-959
[QR20(WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
Diagnostic ProcedureEBS00MXE
1.RETIGHTEN GROUND SCREWS
1. Turn ignition switch “OFF”.
2. Loosen and retighten engi

Page 1310 of 3833

NISSAN X-TRAIL 2001 Service Repair Manual EC-960
[QR20(WITH EURO-OBD)]
DTC P0335 CKP SENSOR (POS)
4. CHECK CKP (POS) GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch “OFF”.
2. Check harness continuity between CKP sensor (POS) ter

Page 1311 of 3833

NISSAN X-TRAIL 2001 Service Repair Manual DTC P0335 CKP SENSOR (POS)
EC-961
[QR20(WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
Component InspectionEBS00MXF
CRANKSHAFT POSITION SENSOR (POS)
1. Loosen the fixing bolt of the sensor.
2. Disconnect

Page 1312 of 3833

NISSAN X-TRAIL 2001 Service Repair Manual EC-962
[QR20(WITH EURO-OBD)]
DTC P0340 CMP SENSOR (PHASE)
DTC P0340 CMP SENSOR (PHASE)
PFP:23731
Component DescriptionEBS00MXH
The camshaft position sensor (PHASE) senses the retraction of the

EC-962
[QR20(WITH EURO-OBD)]
DTC P0340 CMP SENSOR (PHASE)
DTC P0340 CMP SENSOR (PHASE)
PFP:23731
Component DescriptionEBS00MXH
The camshaft position sensor (PHASE) senses the retraction of the
signalplate at the rear end of intake camshaft to identify a particular
cylinder. It also senses the piston position.
When the crankshaft position sensor (POS) system becomes inoper-
ative, the camshaft position sensor (PHASE) provides various con-
trols of engine parts instead, utilizing timing of cylinder identification
signals.
The sensor consists of a permanent magnet and Hall IC.
When engine is running, the high and low parts of the teeth cause
the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor changes.
ECM Terminals and Reference ValueEBS00MXI
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
On Board Diagnosis LogicEBS00MXJ
PBIB0562E
TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
63 L/WCamshaft position
sensor (PHASE)[Engine is running]
●Warm-up condition
●Idle speed1.0 - 4.0V
[Engine is running]
●Engine speed is 2,000 rpm.1.0 - 4.0V
PBIB0525E
PBIB0526E
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0340
0340Camshaft position sen-
sor (PHASE) circuit
●The cylinder No. signal is not sent to ECM
for the first few seconds during engine
cranking.
●The cylinder No. signal is not set to ECM
during engine running.
●The cylinder No. signal is not in the normal
pattern during engine running.
●Harness or connectors
(The sensor circuit is open or shorted)
●Camshaft position sensor (PHASE)
●Camshaft (Intake)
●Starter motor (Refer to SC-20 .)
●Starting system circuit (Refer to SC-20 .)
●Dead (Weak) battery

Load next 8 pages

Page: < prev 1-10 ... 1273-1280 1281-1288 1289-1296 1297-1304 1305-1312 1313-1320 1321-1328 1329-1336 1337-1344 ... 3840 next >

lane assist timing belt brake sensor service reset wiper size wheelbase