Page 4465 of 4770
CHILD RESTRAINT SEAT TOP STRAP BRACKET INSTALLATION ± BO010-02May 24, 2002
Page 9 of 9
OWNER'S
MANUALTercel Sedan/
CoupeTercel WagonTruck 2x4Truck 4x4TundraVan
2000Standard
1999pg 60
h
1998pg 59
h
1997pg 54
h
1996pg 41
h
1995pg 38
h
1994pg 39
hpg 32
gpg 32
g
1993pg 35
hpg 27
gpg 27
g
1992pg 29
hpg 27
gpg 27
g
1991pg 28
hpg 26
gpg 26
g
1990pg 26
gpg 26
g
1989pg 29
gpg 29
gpg 37
a
1988pg 13
gpg 19
gpg 23
a
1987pg 12
gpg 11
gpg 14
gpg 18
gpg 21
a
1986pg 12
gpg 12
gpg 13
gpg 17
gpg 20
a
1985pg 12
gpg 15
gpg 17
a
1984pg 12
gpg 12
gpg 17
a
1983N/AN/A
Installation
Reference
Information
(Continued)
Page 4466 of 4770

Toyota Supports ASE CertificationPage 1 of 3
BO011±01
Title:
NEW SEAT BELT TONGUE PLATE
STOPPER SERVICE PARTS
Models:
All Applicable Models
Technical Service
BULLETIN
March 23, 2001
A new service part for the seat belt tongue plate stopper has been introduced.
Installation procedures are provided to supplement the Repair Manual.
MODELYEAR
Avalon1995 ± 2001
Camry1983 ± 2001
Corolla1980 ± 2001
Camry Solara1999 ± 2001
Sienna (Front Seat Belt Only)1998 ± 2001
RAV41997 ± 2001
4Runner1992 ± 2001
Land Cruiser1991 ± 2001
Tundra2000 ± 2001
Tacoma1997 ± 2000
ECHO2000 ± 2001
Celica1980 ± 2001
Prius2001
Tercel1981 ± 1999
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
N/A73219±02010Stopper, Tongue Plate (Black)*
N/A73219±02020Stopper, Tongue Plate (Gray)*
N/A73219±02030Stopper, Tongue Plate (Beige)*
* Use a stopper color that is closest to the seat belt webbing color.
OP CODEDESCRIPTIONTIMEOPNT1T2
BD0047Install Seat Belt Tongue Plate Stopper0.173219±020#06212
Applicable Warranty*:
This repair is covered under the Toyota Comprehensive Warranty. This warranty is
in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's
in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information
Page 4467 of 4770

NEW SEAT BELT TONGUE PLATE STOPPER SERVICE PARTS ± BO011±01 March 23, 2001
Page 2 of 3
1. Preparation
A. Shift the Tongue Plate to the
upper portion of the Tongue Plate
Stopper, and temporarily hold it
with a clip or tape.
B. Remove any pieces of the original
Tongue Plate Stopper in the
webbing, with a pair of pliers.
CAUTION:
Damaged or weakened seat belts may
break in an accident and injure the
occupant. The seat belt assembly must
be replaced if:
The webbing is cut, frayed, worn, or
damaged.
It has been used in a severe impact.
Inspect the entire length of webbing
for damage and replace the assembly
if needed. Be careful not to damage
the webbing during repair.
2. Install the New Tongue Plate Stopper
A. Install a new Tongue Plate
Stopper in the hole of the
webbing.
NOTE:
Be aware of the installation direction
of the Tongue Plate Stopper as shown
in the illustration.
B. Pinch the Tongue Plate Stopper
into the webbing using an
adjustable wrench, and turn and
push the adjustment screw by
hand.
HINT:
Press the adjustment screw in order to
position the male and female parts of
the Tongue Plate Stopper parallel to
each other, as shown in illustration.
CAUTION:
DO NOT use pliers. They may damage
the webbing. Installation
Procedure
Tongue
PlateTape
Example of
Broken Tongue
Plate Stopper
Tongue Plate
Stopper
Webbing
Page 4468 of 4770
NEW SEAT BELT TONGUE PLATE STOPPER SERVICE PARTS ± BO011±01 March 23, 2001
Page 3 of 3
C. When the adjustment screw for
the adjustable wrench can't be
turned by hand, tighten the
adjustment screw using a pair of
adjustable joint pliers until the
space between jaws of the
adjustable wrench is 4.5 ± 5.0 mm.
(See illustrations.)
D. Check to be sure that the male
pin of the Tongue Plate Stopper
has become deformed evenly in
the hole of the female part and is
firmly held to the belt webbing.
(See illustrations.)
4.5 ± 5.0 mm
Installation
Procedure
(Continued)
CORRECT
INCORRECT
Page 4469 of 4770

Toyota Supports ASE CertificationPage 1 of 2
BO012±99
Title:
DOOR GLASS DISPLACEMENT FIELD FIX
Models:
'98 ± '99 TMMK Camry
Technical Service
BULLETIN
September 3, 1999
On some 1998 and 1999 Camry Vehicles, the door glass may be displaced from the front
door glass run if the door is closed forcefully with the windows partially down. A field fix
has been developed in order to remedy this condition.
1998 ± 1999 TMMK Camrys built before 4T1BG * * K * XU553205
4T1BF * * K * XU084313
4T1BG * * K * XU903993
4T1BF * * K * XU932180
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
N/A67212±AA010Self±Adhesive Stopper
OP CODECOMBODESCRIPTIONTIMEOPNT1T2
670301AR&R Door Trim/Install Rubber Stopper
± Both Sides0.567402±AA0115357
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information
Page 4470 of 4770
DOOR GLASS DISPLACEMENT FIELD FIX ± BO012±99 September 3, 1999
Page 2 of 2
Refer to 1998 Camry Repair Manual (Vol. 2) Pages BO±11±14.
1. Remove the front door trim to gain access to the window components.
2. Inspect the front and rear lower frames and the door glass run for damage as a result
of the glass being displaced.
In cases of slight deformation of window frames, reform as necessary.
If significantly deformed or damaged, replace the frame.
Replace the window run if cut, torn, mutilated, etc.
3. Replace any damaged parts.
4. Remove front lower frame from the door and attach the self±adhesive rubber stopper
(P/N 67212±AA010) 120 mm from the top of the frame as shown below.
NOTE:
To insure proper adhesion of the self±adhesive rubber stopper, the surface of the
frame must be cleaned to remove any foreign material.
5. Reinstall the front lower frame, door glass run, and door trim.
Stopper
67212±AA010
(50 x 12 x 4.76 mm)
(double sided tape)
120 mm
Repair
Procedure
Page 4471 of 4770

Toyota Supports ASE CertificationPage 1 of 2
BO015±00
Title:
DOOR MIRROR INSTALLATION
Models:
'97 ± '00 Japan Built Camry
Technical Service
BULLETIN
March 24, 2000
The procedures in this bulletin explain in detail how to install the door mirrors.
CAUTION:
If the door mirror is installed incorrectly, a wind noise (air leakage noise) might be
generated.
1997 ± 2000 model year Japan built Camry
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
1. Remove the retaining clip and
speaker (if applicable) from the door.
Discard the removed clip.
2. In order to secure the door mirror in
the correct position, insert the 2 pins
of the door mirror base into the holes
of the door.
3. Push the door mirror against the door
and check that the door mirror base
edge is in contact with the door frame
molding lip.
NOTE:
This area is critical to wind noise
reduction.
BODY
Introduction
Applicable
Vehicles
Warranty
Information
Installation
Procedure
Clip
Speaker
Pins
Molding Lip
Mirror Base
Page 4472 of 4770