2000 TOYOTA CAMRY Can bearing cap

Maintenance Log.
. Cars & Sienna
SCHEDULED MAINTENANCE LOGS31
60,000 Miles or 48 Months
❑Replace engine air filter❑Replace engine coolant
❑Replace engine oil and oil filter❑Rotate tires
❑Replace platinum spark plugs1
❑Replace non-platinum spark plugs (Corolla, Paseo, Tercel)1
❑Repack front wheel bearings (Paseo, Tercel)
❑Re-torque drive shaft flange bolts (Sienna)
❑Inspect the following:__
Ball joints and dust covers__
Drive shaft boots
__
Brake lines and hoses__
Engine valves
__
Brake linings/drums and brake pads/discs__
Exhaust pipes and mountings
__
Charcoal canister
2__
Fuel tank cap gasket
__
Differential oil__
Steering gear box
__
Drive belts__
Steering linkage
__
Fuel lines and connections, fuel tank band__
Transmission fluid or oil
and fuel tank vapor vent system hoses
Additional Maintenance Items for Special Operating Conditions:*❑Inspect nuts and bolts on body and chassis❑Replace differential oil❑Replace transmission fluid or oil
Date: __________________
Mileage: _______________
60,000 Miles or 48 Months
60,000 Miles or 48 Months
DEALER SERVICE VERIFICATION
1Required under the terms of the Emission Control Warranty.2Inspect at 60,000 miles or 72 months, whichever comes first, for Avalon, 6-cyl. Camry,
6-cyl. Camry Solara, Paseo, Sienna and Tercel. Required only for vehicles in California,
Massachusetts and New York.

Maintenance Log.
. Cars & Sienna
SCHEDULED MAINTENANCE LOGS39
120,000 Miles or 96 Months
❑Replace engine air filter❑Replace engine coolant
❑Replace engine oil and oil filter❑Rotate tires
❑Replace platinum spark plugs1
❑Replace non-platinum spark plugs (Corolla, Paseo, Tercel)1
❑Repack front wheel bearings (Paseo, Tercel)
❑Re-torque drive shaft flange bolts (Sienna)
❑Inspect the following:__
Ball joints and dust covers__
Drive shaft boots
__
Brake lines and hoses__
Engine valves
__
Brake linings/drums and brake pads/discs__
Exhaust pipes and mountings
__
Charcoal canister
2__
Fuel tank cap gasket
__
Differential oil__
Steering gear box
__
Drive belts__
Steering linkage
__
Fuel lines and connections, fuel tank band__
Transmission fluid or oil
and fuel tank vapor vent system hoses
Additional Maintenance Items for Special Operating Conditions:*❑Inspect nuts and bolts on body and chassis❑Replace differential oil❑Replace transmission fluid or oil
Date: __________________
Mileage: _______________
120 Months
❑Inspect SRS Air Bag
Date: __________________
Mileage: _______________
120,000 Miles or 96 Months
120,000 Miles or 96 Months
120 Months
120 Months
DEALER SERVICE VERIFICATION
1Required under the terms of the Emission Control Warranty.2Inspect at 120,000 miles or 144 months, whichever comes first, for Avalon, 6-cyl. Camry,
6-cyl. Camry Solara, Paseo, Sienna and Tercel. Required only for vehicles in California,
Massachusetts and New York.DEALER SERVICE VERIFICATION

Maintenance Log.
. SUVs & Tacoma
SCHEDULED MAINTENANCE LOGS47
60,000 Miles or 48 Months
❑Replace engine air filter❑Replace engine coolant❑Replace engine oil and oil filter❑Rotate tires❑Replace limited-slip differential oil (Land Cruiser, RAV4 4WD)1
❑Replace platinum spark plugs (RAV4)2
❑Replace non-platinum spark plugs (Tacoma, 4Runner)2
❑Repack front wheel bearings (Tacoma 2WD)❑Lubricate propeller shaft and re-torque bolts (all 4WD except RAV4)❑Lubricate drive shaft bushings (4WD Tacoma without ADD)❑Re-torque drive shaft flange bolts (all 4WD except Land Cruiser)❑Inspect the following:__
Ball joints and dust covers__
Drive shaft boots
__
Brake lines and hoses__
Engine valves
__
Brake linings/drums and brake pads/discs__
Exhaust pipes and mountings
__
Charcoal canister
3__
Fuel tank cap gasket
__
Differential oil__
Steering gear box
__
Drive belts__
Steering linkage
__
Fuel lines and connections, fuel tank band__
Transfer case oil (4WD models)
and fuel tank vapor vent system hoses__
Transmission fluid or oil
Additional Maintenance Items for Special Operating Conditions:*❑Inspect nuts and bolts on body and chassis❑Replace differential oil❑Replace transfer case oil (4WD models)❑Replace transmission fluid or oil
Date: __________________
Mileage: _______________
60,000 Miles or 48 Months
60,000 Miles or 48 Months
DEALER SERVICE VERIFICATION
1If vehicle is equipped with limited-slip differential.2Required under the terms of the Emission Control Warranty.
3Inspect at 60,000 miles or 72 months, whichever comes first.
Required only for vehicles in California, Massachusetts and New York.

Maintenance Log.
. SUVs & Tacoma
SCHEDULED MAINTENANCE LOGS55
120,000 Miles or 96 Months
❑Replace engine air filter❑Replace engine coolant❑Replace engine oil and oil filter❑Rotate tires❑Replace limited-slip differential oil (Land Cruiser, RAV4 4WD)1
❑Replace platinum spark plugs (RAV4)2
❑Replace non-platinum spark plugs (Tacoma, 4Runner)2
❑Repack front wheel bearings (Tacoma 2WD)❑Lubricate propeller shaft and re-torque bolts (all 4WD except RAV4)❑Lubricate drive shaft bushings (4WD Tacoma without ADD)❑Re-torque drive shaft flange bolts (all 4WD except Land Cruiser)❑Inspect the following:__
Ball joints and dust covers__
Engine valves
__
Brake lines and hoses__
Exhaust pipes and mountings
__
Brake linings/drums and brake pads/discs__
Fuel tank cap gasket
__
Charcoal canister
3__
Steering gear box
__
Differential oil__
Steering linkage
__
Drive belts__
Transfer case oil (4WD models)
__
Drive shaft boots__
Transmission fluid or oil
__
Fuel lines and connections, fuel tank band
and fuel tank vapor vent system hoses
Additional Maintenance Items for Special Operating Conditions:*❑Inspect nuts and bolts on body and chassis❑Replace differential oil❑Replace transfer case oil (4WD models)❑Replace transmission fluid or oil
Date: __________________
Mileage: _______________
120,000 Miles or 96 Months
120,000 Miles or 96 Months
120 Months
DEALER SERVICE VERIFICATION
120 Months
❑Inspect SRS Air Bag
Date: __________________
Mileage: _______________
DEALER SERVICE VERIFICATION
1If vehicle is equipped with limited-slip differential.2Required under the terms of the Emission Control Warranty.
3Inspect at 120,000 miles or 144 months, whichever comes first.
Required only for vehicles in California, Massachusetts and New York.

AUTOMATIC TRANSAXLEPREPARATION ±
AX±8
EQUIPMENT
Feeler gaugeCheck major clearance.
Vernier calipersCheck length of second coast
brake piston rod.
Dial indicator with magnetic baseCheck piston stroke and end play
of the output shaft.
Dial indicatorCheck inside diameter of
major bushing.
Straight edgeCheck side clearance of oil pump.
Torque wrench
LUBRICANT
ItemCapacityClassification
Automatic transaxle fluid:
Dry fill
Drain and refill
6.75 liters (7.10 US qts, 5.94 Imp.qts)
2.5 liters (2.6 US qts, 2.2 Imp.qts)
ATF D±@@@@@: [g 2] or
DEXRON®@@@@@: [g
3](DEXRON®@@@@@: [g 2])
Differential oil0.85 liters (0.89 US qts, 0.75 Imp.qts)
ATF D±@@@@@: [g 2] or
DEXRON®@@@@@: [g
3](DEXRON®@@@@@: [g 2])
SSM (SPECIAL SERVICE MATERIALS)
08826±00090Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG)Differential LH bearing retainer
Differential RH retainer
08833±00070Adhesive 1324,
THREE BOND 1324 or equivalentDifferential RH retainer set bolt
AX02N±02
AX01V±08
AX02P±02

Z00060
No.1 No.2 No.3
No.4
No.5
No.1 No.2 No.3No.5
No.4Mark
1, 2 or 3
Mark
0, 1 or 2
Mark
1, 2, 3, 4, or 5
EXAMPLE: Cylinder block º2º + Crankshaft º1º
= Total number 3 (Use bearing º3º)
Number marked
Cylinder block
Crankshaft
Use bearing123
1
111 2
22
22
333445 000
± ENGINE MECHANICAL (5S±FE)CYLINDER BLOCK
EM±95
1267 Author: Date:
HINT:
If using a standard bearing, replace it with one having the same
number. If the number of the bearing cannot be determined, se-
lect the correct bearing by adding together the numbers im-
printed on the cylinder block and crankshaft, then selecting the
bearing with the same number as the total. There are 5 sizes
of standard bearings, marked º1º, º2º, º3º, º4º and º5º according-
ly.
Reference
Cylinder block main journal bore diameter:
Mark º1º59.020 ± 59.026 mm (2.3236 ± 2.3239 in.)
Mark º2º59.026 ± 59.032 mm (2.3239 ± 2.3241 in.)
Mark º3º59.032 ± 59.038 mm (2.3241 ± 2.3243 in.)
Crankshaft main journal diameter:
Mark º0º54.998 ± 55.003 mm (2.1653 ± 2.1655 in.)
Mark º1º54.993 ± 54.998 mm (2.1651 ± 2.1653 in.)
Mark º2º54.988 ± 54.993 mm (2.1649 ± 2.1651 in.)
Standard sized bearing center wall thickness:
No.3
Mark º1º1.992 ± 1.995 mm (0.0784 ± 0.0785 in.)
Mark º2º1.995 ± 1.998 mm (0.0785 ± 0.0787 in.)
Mark º3º1.998 ± 2.001 mm (0.0787 ± 0.0788 in.)
Mark º4º2.001 ± 2.004 mm (0.0788 ± 0.0789 in.)
Mark º5º2.004 ± 2.007 mm (0.0789 ± 0.0790 in.)
Others
Mark º1º1.997 ± 2.000 mm (0.0786 ± 0.0787 in.)
Mark º2º2.000 ± 2.003 mm (0.0787 ± 0.0789 in.)
Mark º3º2.003 ± 2.006 mm (0.0789 ± 0.0790 in.)
Mark º4º2.006 ± 2.009 mm (0.0790 ± 0.0791 in.)
Mark º5º2.009 ± 2.012 mm (0.0791 ± 0.0792 in.)
(k) Complately remove the Plastigage.
19. REMOVE CRANKSHAFT
(a) Lift out the crankshaft.
(b) Remove the 5 upper bearings and 2 upper thrust washers
from the cylinder block.
HINT:
Arrange the main bearing caps, bearings and thrust washers in
the correct order.