Page 3633 of 4770
N20951
A
Instrument Panel Wire Harness
No.1 Defroster Nozzle Garnish
Defroster Nozzle Assembly A
A
RH Side Defroster Duct Nozzle
No.1
Side Defroster
Duct Nozzle
A
A
A
A
A
ANo.2 Heater Duct to
Register
No.3 Instrument
Panel Register
Assembly K
K
K
K
K
K
No.1 Heater Duct to
RegisterAAA
No.1 Instrument Panel
Regigter AssemblyNo.2 Instrument
Panel Register
AssemblyInstrument
Panel Center
Bracket
Instrument PanelGlove Box
Light Assembly
± BODYINSTRUMENT PANEL
BO±73
2431 Author: Date:
2001 CAMRY (RM819U)
Page 3634 of 4770
H01983
Code Shape Size
Code Shape Size
Code Shape Size
A
D
G
J
M
PBC
EF
HI
K
NL
O L = 16 (0.63) ù = 5.2 (0.21)mm (in.)
L = 16 (0.63) ù = 6.0 (0.24)
L = 20 (0.79) ù = 6.0 (0.24)
L = 20 (0.79) ù = 6.0 (0.24)
L = 10 (0.39) ù = 5.0 (0.20)
L = 20 (0.79) ù = 5.2 (0.21)
L = 22 (0.87) ù = 8.0 (0.31)
L = 20 (0.79) ù = 6.0 (0.24)
L = 20 (0.79) ù = 6.0 (0.24)
L = 18 (0.79) ù = 6.0 (0.24)
L = 14 (0.55) ù = 5.0 (0.20)
L = 12 (0.47) ù = 5.0 (0.20)
L = 18 (0.17) ù = 8.0 (0.31)8 x 1.256 x 1.00
6 x 1.00 BO±74
± BODYINSTRUMENT PANEL
2432 Author: Date:
2001 CAMRY (RM819U)
HINT:
Screw shapes and size are indicated in the table below. The code (ºAº±ºPº) correspond to those indicated
on the previous page.
Page 3635 of 4770
BO0MC±02
N20987
N21123
± BODYINSTRUMENT PANEL
BO±75
2433 Author: Date:
2001 CAMRY (RM819U)
REMOVAL
1. REMOVE THESE PARTS:
HINT:
Tape a screwdriver tip before use.
(a) Front door inside scuff plates
(b) Cowl side trims
(c) Front pillar garnishes
(d) Front door opening covers
(e) Lower finish plate
2. REMOVE STEERING WHEEL
(See page SR±11)
3. REMOVE STEERING COLUMN COVERS
(a) Remove the steering tilt handle.
(b) Remove the 3 screws, then the upper and lower column
covers.
4. REMOVE COMBINATION SWITCH
5. REMOVE No.1 LOWER PANEL
(a) Remove the 2 screws and hood lock release lever.
(b) Press on the sides of the coin box while pulling the coin
box outward, and remove the coin box.
(c) Remove the screw, bolt and the No.1 lower panel.
6. REMOVE LOWER PANEL INSERT
(a) Remove the 2 screws holding the DLC3 to the LH lower
panel.
(b) Remove the 4 bolts, and the panel.
7. REMOVE No.2 LOWER COVER
Page 3636 of 4770

N20988
N21023
7 Clips
N21024
6 Clips BO±76
± BODYINSTRUMENT PANEL
2434 Author: Date:
2001 CAMRY (RM819U)
8. REMOVE GLOVE COMPARTMENT ASSEMBLY
(a) Using a screwdriver, remove the glove compartment door
finish plate to the glove compartment box inside.
NOTICE:
When handling the airbag connector, be careful not to dam-
age the airbag wire harness.
HINT:
Tape the screwdriver tip before use.
(b) Pull up and disconnect the airbag connector.
(c) Remove the 4 screws, bolt and glove compartment as-
sembly.
9. REMOVE CENTER CONSOLE UPPER PANEL
Using a screwdriver, remove the panel, then disconnect the
connector.
HINT:
Tape the screwdriver tip before use.
10. REMOVE REAR CONSOLE BOX
Remove the 2 bolts, 2 screws and the console box.
11. REMOVE CENTER CLUSTER FINISH PANEL
Using a screwdriver, remove the panel, then disconnect the
connector.
HINT:
Tape the screwdriver tip before using.
12. REMOVE FRONT CONSOLE BOX
Remove the 2 screws and the front console box.
13. REMOVE RADIO ASSEMBLY
14. REMOVE A/C CONTROL ASSEMBLY
(See page AC±88 and AC±95)
15. REMOVE HAZARD WARNING SWITCH
16. REMOVE CLUSTER FINISH PANEL
(a) Remove the 2 screws.
(b) Using a screwdriver, remove the panel.
HINT:
Tape the screwdriver tip before use.
17. REMOVE COMBINATION METER
18. REMOVE REMOTE CONTROL MIRROR HOLE BASE
Page 3637 of 4770

W03509
N20991
N20992
N20993
± BODYINSTRUMENT PANEL
BO±77
2435 Author: Date:
2001 CAMRY (RM819U)
19. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY
(See page RS±28)
Remove the 2 bolts, 4 nuts and the front passenger airbag as-
sembly.
Torque:
Bolt: 20 N´m (200 kgf´cm, 14 ft´lbf)
CAUTION:
Store the front passenger airbag door facing upward
(never downward).
Never disassemble the front passenger airbag as-
sembly.
NOTICE:
The 2 bolts to the instrument panel have been anti±rust
treated. After removing the front passenger airbag assem-
bly, always replace the bolts and nuts with new ones.
20. REMOVE No.1 AND No.2 INSTRUMENT PANEL
BRACKETS
Remove the 4 bolts and the No.1 and No.2 panel brackets.
21. REMOVE NO.2 SIDE DEFROSTER NOZZLE
22. REMOVE INSTRUMENT PANEL ASSEMBLY
(a) Disconnect the connectors from the LH and RH connector
holders.
(b) Remove the bolts holding the ground wire to the body.
(c) Remove the connector holder from the body.
(d) Disconnect the connectors.
(e) Remove the bolt holding the ground wire to the No.2
instrument panel brace.
Page 3638 of 4770

N20994
N20995
N20996
N20997
BO±78
± BODYINSTRUMENT PANEL
2436 Author: Date:
2001 CAMRY (RM819U)
(f) Remove the bolt, nut, screw and the instrument panel as-
sembly.
23. REMOVE INSTRUMENT PANEL BRACES
(a) Remove the wire brackets and connector.
(b) Remove the bolt and connector from the No.1 instrument
panel brace.
(c) w/ Wireless Control:
Remove the nut and the wireless control unit from the
No.1 instrument panel brace.
(d) Remove the nut holding the radio antenna to the No.2
instrument panel brace.
(e) Remove a nut and brace mount bracket.
(f) Remove the 6 nuts, 2 bolts and No.1 and No.2 instrument
panel braces.
24. REMOVE INSTRUMENT PANEL REINFORCEMENT
(a) Remove the connectors from the steering column tube.
(b) Remove the 4 wire brackets and connectors.
(c) Remove the 2 nuts and bolt holding the No.1 Junction Box
(J/B) to the reinforcement.
(d) Remove the 4 nuts and the steering column from the rein-
forcement.
(e) Remove the brake pedal spring from the reinforcement
and brake pedal.
(f) Remove the 4 nuts, 3 bolts and the reinforcement.
Page 3639 of 4770
BO0MD±01
N21124
± BODYINSTRUMENT PANEL
BO±79
2437 Author: Date:
2001 CAMRY (RM819U)
DISASSEMBLY
1. REMOVE THESE PARTS:
(a) No.1 defroster nozzle garnish
(b) No.1 defroster nozzle
(c) RH side defroster duct nozzle
(d) No.1 side defroster duct nozzle
(e) No.1 heater duct to register
(f) No.2 heater duct to register
(g) No.2 register assembly
(h) No.3 register assembly
(i) No.1 register assembly
2. REMOVE INSTRUMENT PANEL WIRE HARNESS
Remove the 2 brackets, 8 clips and wire harness.
3. REMOVE INSTRUMENT PANEL CENTER BRACKET
4. REMOVE THESE PARTS:
(a) Clock unit
(b) Glove box light assembly
Page 3640 of 4770
BE0A4±04
I21685
E/G Room J/B No.2
HEAD LH Fuse
(w/o Daytime Running Light)
HEAD RH Fuse
(w/o Daytime Running Light)
HEAD LH (UPR) Fuse
(w/ Daytime Running Light)
HEAD RH (UPR) Fuse
(w/ Daytime Running Light)
DOME Fuse
ECU±B Fuse
Headlight Control Relay
E/G Room R/B No.2
(w/ Daytime Running Light)
HEAD LH (LWR) Fuse
HEAD RH (LWR) Fuse
DRL No.2 Fuse
Daytime Running Light Relay No.2
Daytime Running Light Relay No.3
Daytime Running Light Relay No.4
Headlight
Instrument Panel J/B No.1
GAUGE Fuse
TAIL Fuse
Taillight Control Relay
Integration Relay
Daytime Running
Light Relay (Main)Ignition Switch
Combination Switch
Light Control Switch
Headlight Dimmer Switch
Door Courtesy Switch
Light Failure Sensor
Taillight
Automatic Light
Control Sensor
BE±22
± BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
2232 Author: Date:
2001 CAMRY (RM819U)
HEADLIGHT AND TAILLIGHT SYSTEM
LOCATION