Page 1865 of 4770
AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±69
11. REMOVE OUTER RACES FROM COUNTER DRIVE
GEAR
(a) Drive out the 2 races with a brass bar and hammer.
(b) Tag the races to show the location for reassembly.
12. REMOVE SNAP RING FROM COUNTER DRIVE GEAR
Using a screwdriver, remove the snap ring.
OVERDRIVE PLANETARY GEAR
INSPECTION
MEASURE PLANETARY PINION GEAR THRUST
CLEARANCE
Using a feeler gauge, measure the planetary pinion gear
thrust clearance.
Standard clearance:
0.16±0.56 mm (0.0063±0.0220 in.)
Maximum clearance:
0.61 mm (0.0240 in.)
If the clearance is greater then the maximum, replace the
planetary gear assembly.
AX03Z±03
Page 1866 of 4770
AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±70
COUNTER DRIVE GEAR ASSEMBLY
1. INSTALL SNAP RING INTO COUNTER GEAR
Install the snap ring with a screwdriver.
2. INSTALL OUTER RACES INTO COUNTER DRIVE
GEAR
Using SST, press in the 2 outer races to both sides of the
gear.
SST 09350±32014 (09351±32120, 09351±32150)
HINT: Press in the 2 outer races until they touch the snap
ring. Tap the races in straight, so that they do not tilt.
3. INSTALL OVERDRIVE PLANETARY RING GEAR INTO
COUNTER DRIVE GEAR
(a) Install the snap ring to the ring gear.
(b) While pushing down the ring gear, squeeze the snap ring
end with needle±nose pliers, and install it into the groove.
4. INSTALL REAR BEARING
Using SST, press in the bearing onto the shaft.
SST 09350±32014 (09351±32120)
HINT: Press in the bearing until the side surface of the in-
ner race touches the planetary carrier.
AX040±03
Page 1867 of 4770
AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±71
5. INSTALL COUNTER DRIVE GEAR AND FRONT BEAR-
ING
(a) Install the gear onto the shaft, and mesh the ring gear with
the planetary pinions.
(b) Place the front bearing on to the shaft.
(c) Using SST, press in the bearing until there is slight play
between the bearings.
SST 09350±32014 (09351±32120)
HINT: Hold the ring gear to prevent it from falling.
6. INSTALL INTERMEDIATE SHAFT BEARING
Using SST, press in the bearing until it slightly touches the
front bearing of the counter drive gear.
SST 09350±32014 (09351±32120)
HINT: The counter drive gear can be turned lightly.
7. PLACE NEW LOCKING WASHER
8. INSTALL ADJUSTING NUT AND ADJUST PRELOAD
OF COUNTER DRIVE GEAR
(a) Hold the overdrive planetary gear in a vise with soft jaws.
(b) Using SST, tighten the adjusting nut until the following
gear starting load is reached on the tension gauge.
SST 09350±32014 (09351±32080)
Preload (at starting):
9.2±15.3 N (940±1,560 g, 2.1±3.4 lb)
Page 1868 of 4770
AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±72
HINT: Turn the counter drive gear right and left several
times before measuring the preload.
(c) Lock the adjusting nut with one locking washer tab. Bend
the locking washer tab until it is flat with the adjusting nut
groove.
9. INSTALL NO.3 OVERDRIVE PLANETARY THRUST
WASHER
10. INSTALL PINION SHAFT PLUGS
Install the 4 plugs into the pinion shaft.
11. INSTALL OVERDRIVE ONE±WAY CLUTCH AND RE-
TAINING PLATE
(a) Install the one±way clutch into the outer race.
(b) Install the 2 retainers on both sides of the one±way clutch.
(c) Install the one±way clutch into the overdrive planetary
gear.
HINT: Be sure that the one±way clutch is installed in the
correct direction.
(d) Install the retaining plate.
Page 1869 of 4770
AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±73
(e) Install the snap ring.
12. CHECK OPERATION OF O/D ONE±WAY CLUTCH
(a) Install the overdrive direct clutch into the one±way clutch.
(b) Hold the overdrive direct clutch and turn the intermediate
shaft. The shaft should turn freely clockwise and should
lock counterclockwise.
(c) Remove the overdrive direct clutch.
OVERDRIVE CASE DISASSEMBLY
1. REMOVE C0 ACCUMULATOR PISTON FROM OVER-
DRIVE CASE
(a) Using snap ring pliers, remove the snap ring.
(b) Remove the retaining plate and 2 springs.
(c) Remove the accumulator piston.
(d) Remove the O±ring from the piston.
AX041±02
Page 1870 of 4770
AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±74
2. REMOVE OIL SEAL RINGS
OVERDRIVE CASE ASSEMBLY
1. INSTALL OIL SEAL RINGS ON OVERDRIVE CASE
Install the 2 oil seal rings to the overdrive case groove,
then snug them down by squeezing their ends together.
HINT: After installing the oil seal rings, check that they
move smoothly.
2. INSTALL C0 ACCUMULATOR PISTON TO OVER-
DRIVE CASE
(a) Install a new O±ring to the accumulator piston.
(b) Coat the O±ring with ATF.
(c) Install the accumulator piston, 2 springs and retaining
plate.
(d) Using snap ring pliers, install the snap ring.
AX042±02
Page 1871 of 4770
AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±75
OVERDRIVE BRAKE ASSEMBLY
1. INSTALL PISTON INTO DRUM
(a) Install new O±rings to the piston.
Coat the new O±rings with ATF.
(b) Press the piston into the drum, being careful not to dam-
age the O±rings.
2. INSTALL FLANGE, DISCS AND PLATES
Install the flange, discs and plates.
Install in order:
P=Plate D=Disc
Flange±D±P±D±P±D±P
3. POSITION PISTON RETURN SPRING
AX043±05
Page 1872 of 4770
AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±76
4. INSTALL SNAP RING INTO CASE
Be sure the end gap of the snap ring is not aligned with
one of cutouts.
5. INSTALL OVERDRIVE PLANETARY GEAR ONTO OV-
ERDRIVE DIRECT CLUTCH
While turning the overdrive planetary gear clockwise,
install it onto the overdrive direct clutch.
HINT: If the overdrive planetary gear is properly installed
onto the direct clutch, the counter drive gear height from
the overdrive case will be about 24 mm (0.94 in.).