Page 2273 of 4770

F07214
W03269
W03270
W03268
W03271
± BRAKEABS ACTUATOR (DENSO Made)
BR±51
2074 Author: Date:
(c) Place the ºSHEET Pº (SST) on the actuator checker.
SST SST 09990±00430
4. INSPECT BRAKE ACTUATOR OPERATION
(a) Start the engine, and run it at idle.
(b) Turn the selector switch of the actuator checker to
ºFRONT LHº position.
(c) Push and hold in the MOTOR switch for a few seconds.
(d) Depress the brake pedal and hold it until step (g) is com-
pleted.
(e) Push the MAIN push switch, and check that the brake
pedal does not go down.
NOTICE:
Do not keep the MAIN push switch pushed down for more
than 10 seconds.
(f) Release the switch, and check that the pedal goes down.
(g) Push and hold in the MOTOR switch for a few seconds,
and check that the pedal returns.
(h) Release the brake pedal.
(i) Push and hold in the MOTOR switch for a few seconds.
(j) Depress the brake pedal and hold it for about 15 seconds.
As you hold the pedal down, push the MOTOR switch for
a few seconds. Check that the brake pedal does not pul-
sate.
(k) Release the brake pedal.
(l) Turn the selector switch to ºREAR RHº position.
(m) Repeat (c) to (j), checking the actuator operation similarly.
(n) Similarly, inspect ºREAR LHº and ºFRONT RHº position.
HINT:
When inspecting ºFRONT RHº position, push the FRONT RH
switch instead of the MAIN push switch, and you can inspect in
any selector switch position.
Page 2274 of 4770
W03267
BR±52
± BRAKEABS ACTUATOR (DENSO Made)
2075 Author: Date:
(o) Push and hold in the MOTOR switch for a few seconds.
(p) Stop the engine.
5. DISCONNECT ACTUATOR CHECKER (SST) FROM
ACTUATOR
Remove the ºSHEET Pº (SST) and disconnect the actuator
checker (SST) and sub±wire harness (SST) from the actuator.
SST 09990±00150, 09990±00250, 09990±00300,
09990±00360, 09990±00430
6. CONNECT CONNECTORS
Connect the 2 connectors to the actuator.
7. CLEAR DTC (See page DI±493)
Page 2275 of 4770
BR0BE±02
W03266
ABS Actuator
Cushion
Holder
Cushion
Actuator BracketA/C Tube Clamp
Bracket
N´m (kgf´cm, ft´lbf) : Specified torque
15 (155, 11)5.4 (55, 48 in.´lbf)
19 (195, 14)
19 (195, 14)
± BRAKEABS ACTUATOR (DENSO Made)
BR±53
2076 Author: Date:
COMPONENTS
Page 2276 of 4770
BR0BF±02
W03243
SST BR±54
± BRAKEABS ACTUATOR (DENSO Made)
2077 Author: Date:
REMOVAL
1. REMOVE RIGHT FRONT FENDER LINER
2. REMOVE A/C TUBE CLAMP BRACKET BOLT
3. DISCONNECT BRAKE LINES
Using SST, disconnect the 6 brake lines from the ABS actuator.
SST 09751±36011
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
4. REMOVE ABS ACTUATOR ASSEMBLY
(a) Disconnect the 2 connectors.
(b) Remove the 2 blots, 2 nuts and ABS actuator assembly.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
5. REMOVE ABS ACTUATOR
(a) Remove the 2 nuts and ABS actuator from actuator
bracket.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Remove the 2 holders and 3 cushions from the ABS ac-
tuator.
Page 2277 of 4770
BR0BG±02
± BRAKEABS ACTUATOR (DENSO Made)
BR±55
2078 Author: Date:
INSTALLATION
Installation is in the reverse order of removal (See page BR±54).
HINT:
After installation, fill the brake reservoir with brake fluid, bleed the brake system (See page BR±4).
Check for leaks.
Page 2278 of 4770
BR0BH±03
W03327
Holder
Cushion
CushionA/C Tube Clamp Bracket ABS Actuator
(w/ ECU)
Actuator Bracket
N´m (kgf´cm, ft´lbf): Specified torque
9.0 (92, 80 in.´lbf)
15 (155, 11)
19 (195, 14)
19 (195, 14)
F07215
Actuator ECU
Non±reusable part
N´m (kgf´cm, ft´lbf): Specified torque
2.6 (27, 23 in.´lbf)
BR±56
± BRAKEABS ACTUATOR (BOSCH Made)
2079 Author: Date:
ABS ACTUATOR (BOSCH Made)
COMPONENTS
Page 2279 of 4770
BR0BI±03
W03324
SST
W03325Release Bar
± BRAKEABS ACTUATOR (BOSCH Made)
BR±57
2080 Author: Date:
REMOVAL
1. REMOVE RIGHT FRONT FENDER LINER
2. REMOVE A/C TUBE CLAMP BRACKET BOLT
3. DISCONNECT BRAKE LINES
Using SST, disconnect the 6 brake lines from the ABS actuator.
SST 09751±36011
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
4. DISCONNECT CONNECTOR
Pull out the release bar, and disconnect the connector.
5. REMOVE ABS ACTUATOR ASSEMBLY
Remove the 2 bolts, 2 nuts and ABS actuator assembly.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
6. REMOVE ABS ACTUATOR
(a) Remove the 2 nuts and ABS actuator.
Torque: 9.0 N´m (92 kgf´cm, 80 in.´lbf)
(b) Remove the 2 holders and 3 cushions from the ABS ac-
tuator.
Page 2280 of 4770
BR0BJ±02
W03326
BR±58
± BRAKEABS ACTUATOR (BOSCH Made)
2081 Author: Date:
DISASSEMBLY
1. DISCONNECT CONNECTOR
Disconnect the connector, and remove the wire harness from
the harness guide.
2. REMOVE ECU
(a) Using a T20 torx wrench, loosen the 6 screws.
Torque: 2.6 N´m (27 kgf´cm, 23 in.´lbf)
NOTICE:
When removing the ECU from the actuator, it must be
removed it upward.
At the time of reassembly, tighten the screws accord-
ing to the order shown on the left.
(b) Remove the ECU from the actuator.
NOTICE:
Protect the actuator in order to prevent sealing surface
from getting dirty and causing damage on the valve body.
If the dirt and the like are stuck to the sealing surface, use
plastic tools or soft objects to remove the dirt. Do not use
chemical solvents.