2000 TOYOTA CAMRY compression ratio
[x] Cancel search: compression ratioPage 13 of 4770
3
CAMRY ± NEW FEATURES33
5S-FE ENGINE
1. Description
The intake and exhaust systems have been changed to increase torque and reduce noise. On the California
specification model, the air assist system has been discontinued.
Engine Specifications
ItemNewPrevious
No. of Cyls. & Arrangement4-Cylinder, In-Line
Valve Mechanism16-Valve DOHC,
Belt & Gear Drive
Combustion CamberPentroof Type
ManifoldsCross-Flow
Fuel SystemSFI
Displacement cm3 (cu. in.)2164 (132.0)
Bore x Stroke mm (in.)87.0 x 91.0 (3.43 x 3.58)
Compression Ratio9.5 : 1
Max. Output [SAE-NET]
101 kW @ 5200 rpm
(136 HP @ 5200 rpm)
99 kW @ 5200 rpm*
(133 HP @ 5200 rpm)*99 kW @ 5200 rpm
(133 HP @ 5200 rpm)
97 kW @ 5200 rpm*
(130 HP @ 5200 rpm)*
Max. Torque [SAE-NET]
203 N.m @ 4400 rpm
(150 ft-lbf @ 4400 rpm)
201 N
.m @ 4400 rpm*
(148 ft-lbf @ 4400 rpm)*
199 N.m @ 4400 rpm
(147 ft
.lbf @ 4400 rpm)
197 N
.m @ 4400 rpm*
(145 ft
.lbf @ 4400 rpm)*
IntakeOpen3 BTDC
Valve
IntakeClose43 ABDCValve
Timing
ExhaustOpen45 BBDCg
ExhaustClose3 AT D C
Fuel Octane Number RON91
Oil GradeAPI SJ EC-II, ILSAC or Better
*: California Specification Models
Page 16 of 4770
CAMRY ± NEW FEATURES36
5S-FNE ENGINE
1. Description
The 5S-FNE engine is a new engine that uses CNG (Compressed Natural Gas) as fuel, which has been devel-
oped based on the 5S-FE gasoline engine.
The main component of natural gas is methane (CH
4), which has fewer carbous (C) than gasoline (mean mo-
lecular formula: C
7.5H13.4). Therefore, the amount of CO2 discharged by this engine is approximately 70%
that of the gasoline engine. Furthermore, this engine achieves low-emission operation by precisely controlled
air-fuel ratio and using special catalysts for the CNG application.
However, because the fuel is in the gaseous form, its volumetric efficiency is low, causing lower power output
if this fuel is used in the base engine.
Therefore, the 5S-FNE engine has adopted the following features: a high compression ratio, the intake valves
with early closed timing, the intake and exhaust valves with increased lift, a low back pressure muffler made
possible by the 2-way exhaust system, injectors for gaseous fuel, and a catalytic converter designed exclu-
sively for CNG application. At the same time, precision air-fuel ratio control is effected through the use of
the air-fuel ratio sensor* and the heater oxygen sensor, thus achieving the level of performance that is equiva-
lent to the base engine. Moreover, this engine realizes extremely low emissions and restoring engine torque.
*: Already adopted on the California specification 5S-FE engine.
Specifications
Item5S-FNE Engine5S-FE Engine
No. of Cyls. & Arrangement4-Cylinder, In-Line
Valve Mechanism16-Valve DOHC,
Belt & Gear Drive
Combustion CamberPentroof Type
ManifoldsCross-Flow
Fuel SystemSFI
Displacement cm3 (cu.in.)2164 (312.0)
Bore x Stroke mm (in.)87.0 x 91.0 (3.43 x 3.58)
Compression Ratio11.0 : 19.5 : 1
Max. Output [SAE-NET]88 kW @ 5200 rpm
(118 HP @ 5200 rpm)
101 kW @ 5200 rpm
(136 HP @ 5200 rpm)
97 kW @ 5200 rpm*
(133 HP @ 5200 rpm)*
Max. Torque [SAE-NET]178 N.m @ 2400 rpm
(131 ft-lbf @ 2400 rpm)
203 N.m @ 4400 rpm
(150 ft-lbf @ 4400 rpm)
201 N
.m @ 4400 rpm*
(148 ft-lbf @ 4400 rpm)*
IntakeOpen3 BTDC
Valve
IntakeClose38 ABDC43 ABDCValve
Timing
ExhaustOpen45 BBDCExhaustClose3 AT D C
Fuel Octane Number RON13091
Oil GradeAPI SJ EC or ILSAC
*: California Specification Models
Page 18 of 4770
CAMRY ± NEW FEATURES 38
2. Features of 5S-FNE Engine
Features of the 5S-FNE engine are listed below.
Item
Features
Performance
High compression ratio is used.
High lift camshaft is used.
Low back pressure muffler is used.
Fuel Economy
High compression ratio is used.
Valve spring load has been reduced.
Low-friction. TiN (titanium nitride) coated valve lifters has been adopted.
Low Emission
A fuel injection system containing gas injectors has been adopted.
Because the fuel is in the gaseous state, it does not come in contact with
the wall surface, making optimal air-fuel ratio control possible
immediately after the engine has been started.
Precision air-fuel ratio feedback control that uses an air-fuel ratio sensor
and a heated oxygen sensor has been adopted.
Two catalytic converters designed exclusively for the natural gas engine
have been adopted: the WU-TWC (Warm Up Three-Way Catalytic
Converter) and the TWC (Three-Way Catalytic Converter).
Other Features
Highly rigid pistons have been adopted to accommodate the high
compression ratio.
A CNG (Compressed Natural Gas) pressure regulator that precisely
regulates the CNG has been adopted.
A large-bore delivery pipe and fuel hose with minimal internal conduit
resistance have been adopted.
The electro magnetic fuel shutoff valve is added on the delivery pipe.
A fuel pressure sensor that corrects the fuel injection volume and a fuel
temperature sensor have been provided on the delivery pipe.
The starting performance of the engine at low temperatures has been
ensured by increasing the volume of the airflow of the IAC (Idle Air
Control).
Materials that excel in wear resistance have been adopted on the valves
and valve seats for both the intake and exhaust.
Rust-resistant spark plugs have been adopted.
Aluminum lining and carbon fiber have been adopted in the fuel tank.
For the fuel gauge, a fuel tank fuel temperature sensor and a fuel pipe fuel
pressure sensor have been adopted.
Page 19 of 4770
3
CAMRY ± NEW FEATURES
167CN03 167CN02
5S-FNE Engine 5S-FE Engine39
3. Engine Proper
General
The cylinder head and the pistons have been changed for the CNG application.
Cylinder Head
Materials that excel in wear resistance have been adopted on the valve seats for both the intake and exhaust.
The shape of the holes into which the injectors mount has been changed to accommodate the injectors de-
signed exclusively for the CNG application.
The shape of water jacket around plug has been modified to prevent the deformation.
Piston
To achieve a high compression ratio, the shape of the top of the piston has been changed and pin boss hole
with taper has been adopted.
An additional surface treatment has been provided to improve heat resistance.
The material has been changed to increase rigidity.
Page 42 of 4770
APPENDIX ± CAMRY
ItemArea
Body Type
Vehicle Grade
Model Code
OverallLength mm (in.)
Width mm (in.)
Height* mm (in.)
Wheel Base mm (in.)
TreadFront mm (in.)
Rear mm (in.)
Effective Head RoomFront mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.) Effective Leg Room
Shoulder Room
Overhang
Min. Running Ground Clearance mm (in.)
Angle of Approach degrees
Angle of Departure degrees
Curb Weight
Gross Vehicle WeightFront kg (lb)
Rear kg (lb)
Total kg (lb)
Front kg (lb)
Rear kg (lb)
Total kg (lb)
Fuel Tank Capacity (US.gal., Imp.gal)
Luggage Compartment Capacity m
3 (cu.ft.)
Max. Speed km / h (mph)
Max. Cruising Speed km / h (mph)
Acceleration
Max. Permissible
Speed
Turning Diameter
(Outside Front)0 to 100 km / h sec.
0 to 400 m sec.
1st Gear km / h (mph)
2nd Gear km / h (mph)
3rd Gear km / h (mph)
4th Gear km / h (mph)
Wall to Wall m (ft.)
Curb to Curb m (ft.)
Engine Type
Valve Mechanism
Bore x Stroke mm (in.)
Displacement cm
3 (cu.in.)
Compression Ratio
Carburetor Type
Research Octane No. RON
Max. Output (SAE-NET) kW / rpm (HP@rpm)
Max. Torque (SAE-NET) N
.m / rpm (lb-ft@rpm)
Battery Capacity (5HR) Voltage & Amp. hr.
Generator Output Watts
Starter Output kW
Clutch Type
Transaxle Type
Transmission Gear
Ratio
Counter Gear Ratio
Differential Gear Ratio (Final)
Brake Type
Parking Brake Type
Brake Booster Type and Size in.
Proportioning Valve Type
Suspension Type
Stabilizer Bar
Steering Gear Type
Steering Gear Ratio (Overall)
Power Steering TypeIn First
In Second
In Third
In Fourth
In Fifth
In Reverse
Front
Rear
Front
Rear
Front
Rear
5
10
15
20
25
30
35
40
45
50
55
60
65
70
Major Dimensions & Vehicle Weights Performance Engine Engine
Chassis
Electrical
U.S.A.
CE
LE 4-Door Sedan
XLE
11 2
CAMRY
SXV20L-CEMDKA SXV20L-CEPDKA SXV20L-A(C)EPNKA SXV20L-A(C)EPGKA
4790 (188.6)
1780 (70.1)1785 (70.3)
1415 (55.7)
2670 (105.1)
1545 (60.8)
1520 (59.8)
980 (38.6), 950 (37.4)*
1
940 (37.0), 914 (36.0)*1
1102 (43.4)
901 (35.5)
1427 (56.2)
1425 (56.1)
975 (38.4)
1145 (45.1)
130 (5.1)
16
16
810 (1786) 835 (1841) 865 (1907)*
2, 875 (1929)*3870 (1918)*2, 875 (1929)*3
550 (1213) 545 (1202) 540 (1191)*2, 550 (1213)*3545 (1202)*2, 555 (1224)*3
1360 (2999) 1380 (3043) 1405 (3097)*2, 1425 (3142)*31415 (3120)*2, 1430 (3153)*3
965 (2130)995 (2195)
845 (1860)900 (1985)
1810 (3990)1895 (4180)
70 (18.5, 15.4)
0.399 (14.1)
180 (112)
ÐÐÐÐ
ÐÐÐÐ
ÐÐÐÐ
52 (32) 69 (43)
93 (58) 125 (78)
147 (91) Ð Ð Ð
ÐÐÐÐ
11.5 (37.7)
11.0 (36.1)
5S-FE
16-Valve, DOHC
87.0 x 91.0 (3.43 x 3.58)
2164 (132.0)
9.5 : 1
SFI
91
101 / 5200(136@5200),99 / 5200(133@5200)*4203 / 4400(150@4400),201 / 4400(148@4400)*4
12 - 55, 12 - 48*5
960
1.4
Dry, Single Plate Ð Ð Ð
S51 A140E
3.538 2.810
1.960 1.549
1.250 1.000
0.945 0.706
0.731 Ð Ð Ð
3.153 2.296
Ð 0.945
3.944
Ventilated Disc
L.T. Drum
Drum
Tandem 8º + 9ºTandem 8.5º + 8.5º*
2, 8º + 9º*3
Dual-P Valve
MacPherson Strut
MacPherson Strut
STD
STD
Rack and Pinion
17.4 : 1
Integral Type
*: Unladed Vehicle *
3: Produced by TMMK
*1: With Moor Roof *4: California Specification Model
*2: Produced by TMC *5: Without Cold Area Specification Model
Page 44 of 4770
APPENDIX ± CAMRY
ItemArea
Body Type
Vehicle Grade
Model Code
OverallLength mm (in.)
Width mm (in.)
Height* mm (in.)
Wheel Base mm (in.)
TreadFront mm (in.)
Rear mm (in.)
Effective Head RoomFront mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.) Effective Leg Room
Shoulder Room
Overhang
Min. Running Ground Clearance mm (in.)
Angle of Approach degrees
Angle of Departure degrees
Curb Weight
Gross Vehicle WeightFront kg (lb)
Rear kg (lb)
Total kg (lb)
Front kg (lb)
Rear kg (lb)
Total kg (lb)
Fuel Tank Capacity (US.gal., Imp.gal)
Luggage Compartment Capacity m
3 (cu.ft.)
Max. Speed km / h (mph)
Max. Cruising Speed km / h (mph)
Acceleration
Max. Permissible
Speed
Turning Diameter
(Outside Front)0 to 100 km / h sec.
0 to 400 m sec.
1st Gear km / h (mph)
2nd Gear km / h (mph)
3rd Gear km / h (mph)
4th Gear km / h (mph)
Wall to Wall m (ft.)
Curb to Curb m (ft.)
Engine Type
Valve Mechanism
Bore x Stroke mm (in.)
Displacement cm
3 (cu.in.)
Compression Ratio
Carburetor Type
Research Octane No. RON
Max. Output (SAE-NET) kW / rpm (HP@rpm)
Max. Torque (SAE-NET) N
.m / rpm (lb-ft@rpm)
Battery Capacity (5HR) Voltage & Amp. hr.
Generator Output Watts
Starter Output kW
Clutch Type
Transaxle Type
Transmission Gear
Ratio
Counter Gear Ratio
Differential Gear Ratio (Final)
Brake Type
Parking Brake Type
Brake Booster Type and Size in.
Proportioning Valve Type
Suspension Type
Stabilizer Bar
Steering Gear Type
Steering Gear Ratio (Overall)
Power Steering TypeIn First
In Second
In Third
In Fourth
In Fifth
In Reverse
Front
Rear
Front
Rear
Front
Rear
Major Dimensions & Vehicle Weights Performance Engine Engine
Chassis
Electrical
Canada
XLE 4-Door Sedan
CE
5
10
15
20
25
30
35
40
45
50
55
60
65
70 U.S.A.
LE 4-Door Sedan
11 4
MCV20L-AEPDKK MCV20L-AEPGKK SXV23L-AEPNCA
4790 (188.6)
1780 (70.1) 1785 (70.3) 1780 (70.1)
1420 (55.9)
2670 (105.1)
1545 (60.8)
1520 (59.8)
980 (38.6), 950 (37.4)*
1980 (38.6)
940 (37.0), 914 (36.0)*1940 (37.0)
1102 (43.4)
901 (35.5)
1427 (56.2)
1425 (56.1)
975 (38.4)
1145 (45.1)
135 (5.3)130 (5.1)
1616
1616
860 (1896) 920 (2028) 860 (1896)
540 (1190) 545 (1202) 595 (1312)
1400 (3086) 1465 (3230) 1455 (3208)
1040 (2290)970 (2140)
900 (1985)950 (2095)
1940 (4275)1920 (4235)
70 (18.5, 15.4)
135 (35.7, 29.2)*4, 43 (11.4, 9.5)*5
0.399 (14.1)0.332 m3 *6, 8.921 ft3 *7
210 (130)180 (112)
ÐÐ
ÐÐÐ
ÐÐÐ
70 (43)66 (41)
127 (79)119 (74)
ÐÐÐ
ÐÐÐ
11.9 (39.0)
11.4 (37.4)
1MZ-FE5S-FNE
24-Valve, DOHC16-Valve, DOHC
87.5 x 83.0 (3.44 x 3.27)87.0 x 91.0 (3.43 x 3.58)
2995 (182.7)2164 (132.0)
10.5 : 111.0 : 1
SFI
91 or higher130
145 / 5200 (194@5200)88 / 5200 (118@5200)
283 / 4400 (209@4400)178 / 2400 (131@2400)
12 - 55
960
1.4
ÐÐÐ
A541EA140E
2.8102.810
1.5491.549
1.0001.000
0.7350.706
ÐÐÐ
2.296
0.945
3.9334.176
Ventilated Disc
Solid DiscL.T. Drum
Drum
Tandem 8º + 9º
Tandem 8.5º + 8.5º*2, 8º + 9º*3Tandem 8º + 9º
Dual-P Valve
MacPherson Strut
MacPherson Strut
STD
STD
Rack and Pinion
17.4 : 1
Integral Type
*: Unladed Vehicle *
4: Water Volume
*1: With Moon Roof *5: Equivalent Gasoline Capacity
*2: Produced by TMC *6: VDA
*3: Produced by TMMK *7: SAE Suitcase
Page 48 of 4770
CAMRY - MAJOR TECHNICAL SPECIFICATIONS
1st Gear km / h (mph) Angle of Approach degrees
Angle of Departure degrees
ItemArea
Body Type
Vehicle Grade
Model Code
OverallLength mm (in.)
Width mm (in.)
Height*
1mm (in.)
Wheel Base mm (in.)
TreadFront mm (in.)
Rear mm (in.)
Effective Head RoomFront mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.) Effective Leg Room
Shoulder Room
Overhang
Min. Running Ground Clearance mm (in.)
Curb Weight
Gross Vehicle WeightFront kg (lb)
Rear kg (lb)
Total kg (lb)
Front kg (lb)
Rear kg (lb)
Total kg (lb)
Fuel Tank Capacity (US.gal., lmp.gal)
Luggage Compartment Capacity m
3 (cu.ft.)
Max. Speed km / h (mph)
Max. Cruising Speed km / h (mph)
Max. Permissible
Speed
Turning Diameter
(Outside Front)2nd Gear km / h (mph)
3rd Gear km / h (mph)
4th Gear km / h (mph)
Wall to Wall m (ft.)
Curb to Curb m (ft.)
Engine Type
Valve Mechanism
Bore x Stroke mm (in.)
Displacement cm
3 (cu.in.)
Compression Ratio
Carburetor Type
Research Octane No. RON
Max. Output (SAE-NET) kW / rpm (HP@rpm)
Max. Torque (SAE-NET) N
.m / rpm (lb-ft@rpm)
Battery Capacity (5HR) Voltage & Amp. hr.
Generator Output Watts
Starter Output kW
Clutch Type
Transaxle Type
Transmission Gear
Ratio
Differential Gear Ratio (Final)
Brake Type
Parking Brake Type
Brake Booster Type and Size in.
Proportioning Valve Type
Suspension Type
Stabilizer Bar
Steering Gear Type
Steering Gear Ratio (Overall)
Power Steering TypeIn First
In Second
In Third
In Fourth
In Fifth
In Reverse
Front
Rear
Front
Rear
Front
Rear
5
10
15
20
25
30
35
40
45
50
55
60
65
70
Major Dimensions & Vehicle Weights Performance Engine Engine
Chassis
Electrical
U.S.A.
4-Door Sedan
CEXLE
0 to 100 mph sec.
0 to 400 m sec. Acceleration
Counter Gear RatioLE
4
MAJOR TECHNICAL SPECIFICATIONS
SXV20L-CEMDKA SXV20L-CEPDKA SXV20L-A(C)EPNKA SXV20L-A(C)EPGKA
4790 (188.6)
1780 (70.1)1785 (70.3)
1415 (55.7)
2670 (105.1)
1545 (60.8)
1520 (59.8)
980 (38.6), 950 (37.4)*
2
940 (37.0), 914 (36.0)*2
1102 (43.4)
901 (35.5)
1427 (56.2)
1425 (56.1)
975 (38.4)
1145 (45.1)
130 (5.1)
16
16
810 (1786) 835 (1841) 865 (1907)*
3, 875 (1929)*4870 (1918)*3, 875 (1929)*4
550 (1213) 545 (1202) 540 (1191)*3, 550 (1213)*4545 (1202)*3, 555 (1224)*4
1360 (2999) 1380 (3043) 1405 (3097)*3, 1425 (3142)*41415 (3120)*3, 1430 (3153)*4
965 (2130)995 (2195)
845 (1860)900 (1985)
1810 (3990)1895 (4180)
70 (18.5, 15.4)
0.399 (14.1)
180 (112)
ÐÐÐÐ
ÐÐÐÐ
ÐÐÐÐ
52 (32) 69 (43)
95 (58) 125 (78)
147 (91) Ð Ð Ð
ÐÐÐÐ
11.5 (37.7)
11.0 (36.1)
5S-FE
16-Valve, DOHC
87.0 x 91.0 (3.43 x 3.58)
2164 (132.0)
9.5 : 1
SFI
91 or Higher
99 / 5200 (133@5200)
201 / 4400 (148@4400)
12-55, 12-48*
5
960
1.4
Dry, Single Plate Ð Ð Ð
S51 A140E
3.538 2.810
1.960 1.549
1.250 1.000
0.945 0.706
0.731 Ð Ð Ð
3.153 2.296
Ð 0.945
3.944
Ventilated Disc
L.T. Drum
Drum
Tandem 8º + 9ºTandem 8.5º + 8.5º*
3, 8º + 9º*4
Dual-P Valve
MacPherson Strut
MacPherson Strut
STD
STD
Rack and Pinion
17.4 : 1
Integral Type
*
1: Unladed Vehicle *4: Produced by TMMK
*2: With Moor Roof *5: Without Cold Area Specification Model
*3: Produced by TMC
Page 50 of 4770
CAMRY - MAJOR TECHNICAL SPECIFICATIONS
1st Gear km / h (mph) Angle of Approach degrees
Angle of Departure degrees
ItemArea
Body Type
Vehicle Grade
Model Code
OverallLength mm (in.)
Width mm (in.)
Height*
1mm (in.)
Wheel Base mm (in.)
TreadFront mm (in.)
Rear mm (in.)
Effective Head RoomFront mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.) Effective Leg Room
Shoulder Room
Overhang
Min. Running Ground Clearance mm (in.)
Curb Weight
Gross Vehicle WeightFront kg (lb)
Rear kg (lb)
Total kg (lb)
Front kg (lb)
Rear kg (lb)
Total kg (lb)
Fuel Tank Capacity (US.gal., lmp.gal)
Luggage Compartment Capacity m
3 (cu.ft.)
Max. Speed km / h (mph)
Max. Cruising Speed km / h (mph)
Max. Permissible
Speed
Turning Diameter
(Outside Front)2nd Gear km / h (mph)
3rd Gear km / h (mph)
4th Gear km / h (mph)
Wall to Wall m (ft.)
Curb to Curb m (ft.)
Engine Type
Valve Mechanism
Bore x Stroke mm (in.)
Displacement cm
3 (cu.in.)
Compression Ratio
Carburetor Type
Research Octane No. RON
Max. Output (SAE-NET) kW / rpm (HP@rpm)
Max. Torque (SAE-NET) N
.m / rpm (lb-ft@rpm)
Battery Capacity (5HR) Voltage & Amp. hr.
Generator Output Watts
Starter Output kW
Clutch Type
Transaxle Type
Transmission Gear
Ratio
Differential Gear Ratio (Final)
Brake Type
Parking Brake Type
Brake Booster Type and Size in.
Proportioning Valve Type
Suspension Type
Stabilizer Bar
Steering Gear Type
Steering Gear Ratio (Overall)
Power Steering TypeIn First
In Second
In Third
In Fourth
In Fifth
In Reverse
Front
Rear
Front
Rear
Front
Rear
5
10
15
20
25
30
35
40
45
50
55
60
65
70
Major Dimensions & Vehicle Weights Performance Engine Engine
Chassis
Electrical
Canada
4-Door Sedan
CE LE
0 to 100 km / h sec.
0 to 400 m sec. Acceleration
Counter Gear RatioXLE
U.S.A.
6
MCV20L-AEPDKK MCV20L-AEPGKK SXV23L-AEPNCA
4790 (188.6)
1780 (70.1) 1785 (70.3) 1780 (70.1)
1420 (55.9)
2670 (105.1)
1545 (60.8)
1520 (59.8)
980 (38.6), 950 (37.4)*
2980 (38.6)
940 (37.0), 914 (36.0)*2940 (37.0)
1102 (43.4)
901 (35.5)
1427 (56.2)
1425 (56.1)
975 (38.4)
1145 (45.1)
135 (5.3)130 (5.1)
1616
1616
860 (1896) 920 (2028) 860 (1896)
540 (1190) 545 (1202) 595 (1312)
1400 (3086) 1465 (3230) 1455 (3208)
1040 (2290)970 (2140)
900 (1985)950 (2095)
1940 (4275)1920 (4235)
70 (18.5, 15.4)
135 (35.7, 29.2)*5, 43 (11.4, 9.5)*6
0.399 (14.1)0.332 m3 *7, 8.921 ft3 *8
210 (130)180 (112)
ÐÐ
ÐÐÐ
ÐÐÐ
70 (43)66 (41)
127 (79)119 (74)
ÐÐÐ
ÐÐÐ
11.9 (39.0)
11.4 (37.4)
1MZ-FE5S-FNE
24-Valve, DOHC16-Valve, DOHC
87.5 x 83.0 (3.44 x 3.27)87.0 x 91.0 (3.43 x 3.58)
2995 (182.7)2164 (132.0)
10.5 : 111.0 : 1
SFI
91 or higher130
143 / 5200 (192@5200)88 / 5200 (118@5200)
281 / 4400 (207@4400)178 / 2400 (131@2400)
12-55
960
1.4
ÐÐÐ
A541EA140E
2.8102.810
1.5491.549
1.0001.000
0.7350.706
ÐÐÐ
2.296
0.945
3.9334.176
Ventilated Disc
Solid DiscL.T. Drum
Drum
Tandem 8.5º + 8.5º
Dual-P Valve
MacPherson Strut
MacPherson Strut
STD
STD
Rack and Pinion
17.4 : 1
Integral Type
*
1: Unladed Vehicle *5: Water Volume
*2: With Moon Roof *6: Equivalent Gasoline Capacity
*3: Produced by TMC *7: VDA
*4: Produced by TMMK *8: SAE Suitcase