Page 545 of 4449
ATC-116
AUTO AMP
Revision: 2004 November 2004 FX35/FX45
AUTO AMPPFP:27760
Removal and Installation of Unified Meter and A/C Amp.AJS00159
REMOVAL
1. Remove the audio unit. Refer to AV- 4 4 , "Removal and Installation of Audio Unit" .
2. Remove the fixing screws, then remove the unified meter and A/
C amp.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA2035E
Page 546 of 4449
AMBIENT SENSOR
ATC-117
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45
AMBIENT SENSORPFP:27722
Removal and InstallationAJS0015A
REMOVAL
1. Remove front grille. Refer to EI-23, "FRONT GRILLE" .
2. Disconnect ambient sensor connector.
3. Remove ambient sensor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA2016E
Page 547 of 4449
ATC-118
IN-VEHICLE SENSOR
Revision: 2004 November 2004 FX35/FX45
IN-VEHICLE SENSORPFP:27720
Removal and InstallationAJS0015B
REMOVAL
1. Remove instrument driver lower panel. Refer to IP-11, "Removal and Installation" .
2. Remove mounting screw, and then remove in-vehicle sensor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA2036E
Page 548 of 4449
SUNLOAD SENSOR
ATC-119
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45
SUNLOAD SENSORPFP:27721
Removal and InstallationAJS0015C
REMOVAL
1. Remove front defroster grille (right side). Refer to IP-11, "Removal and Installation" .
2. Disconnect sunload sensor connector.
3. Remove sunload sensor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA2026E
Page 549 of 4449

ATC-120
INTAKE SENSOR
Revision: 2004 November 2004 FX35/FX45
INTAKE SENSORPFP:27723
Removal and InstallationAJS0015D
REMOVAL
1. Set the temperature at 18°C (60°F), and then disconnect the battery negative cable.
2. Use a refrigerant collecting equipment (for HFC-134a) to discharge refrigerant.
3. Remove the mounting bolt, and then remove the low-pressure pipe 2 and high-pressure pipe 3. Refer to
ATC-151, "
Removal and Installation of Low-pressure Pipe 2 and High-pressure Pipe 3" .
CAUTION:
Seal connection opening of piping with a cap or vinyl tape to avoid exposure to atmosphere.
4. Slide the evaporator to passenger side, and then remove the
intake sensor.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
Replace O-rings for A/C piping with new ones. Before installing, apply compressor oil to them.
Connection point for female-side piping is thin. So, when inserting male-side piping, take care not
to deform female-side piping. Slowly insert in axial direction.
Insert one-touch joint connection point securely until it clicks.
After piping has been connected, pull male-side piping by hand to make sure piping does not
come off.
When recharging refrigerant, check for leaks.
RJIA0928E
Page 550 of 4449
BLOWER UNIT
ATC-121
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45
BLOWER UNITPFP:27200
Removal and InstallationAJS0015E
REMOVAL
1. Remove instrument passenger lower panel. Refer to IP-11, "Removal and Installation" .
2. Remove ECM with bracket attached.
3. Disconnect intake door motor connector and blower fan motor
connector.
4. Remove harness clip from blower unit.
5. Remove mounting bolt and screws (2), from blower unit.
CAUTION:
Move blower unit rightward, and remove locating pin (1)
and joint. Then remove blower unit downward.
6. Remove blower unit.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
Make sure locating pin (1) and joint are securely inserted.
RJIA2039E
RJIA0943E
Page 551 of 4449
ATC-122
BLOWER UNIT
Revision: 2004 November 2004 FX35/FX45
Disassembly and AssemblyAJS0015F
1. Adapter 2. Intake upper case 3. Filter cover
4. In-cabin microfilter 5. Intake lower case 6. Blower fan motor assembly
7. Motor cover 8. Intake door lever 2 9. Intake door motor
10. Intake door link 11. Intake door lever 3 12. Intake door 2
13. Intake door lever 1 14. Intake door 1 15. Intake bell mouth
SJIA0420E
Page 552 of 4449
BLOWER MOTOR
ATC-123
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45
BLOWER MOTORPFP:27226
Removal and InstallationAJS0015G
REMOVAL
1. Remove instrument lower cover. Refer to IP-11, "Removal and Installation" .
2. Disconnect blower motor connector.
3. Remove screws from blower motor, and then remove it.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA2239E