Page 3697 of 4449

LT-142
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2004 November 2004 FX35/FX45
5. CHECK PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and
front side marker lamp harness connector.
4. Check continuity between IPDM E/R harness connector and
clearance lamp harness connector.
5. Check continuity between IPDM E/R harness connector and
license plate lamp harness connector.
6. Check continuity between IPDM E/R harness connector and
rear combination lamp harness connector.
OK or NG
OK >> Replace IPDM E/R.
NG >> Repair harness or connector.
Terminals
Continuity IPDM E/R Front side marker lamp
ConnectorTerminal
(Wire color)ConnectorTerminal
(Wire color)
E7 22 (R)RH E22
1 (R) Yes
LH E42
PKIA5240E
Terminals
Continuity IPDM E/RClearance lamp
(Parking)
ConnectorTerminal
(Wire color)ConnectorTerminal
(Wire color)
E7 22 (R)RH E23
2 (R) Yes
LH E43
PKIA5241E
Terminals
Continuity IPDM E/R License plate lamp
ConnectorTerminal
(Wire color)ConnectorTerminal
(Wire color)
E7 22 (R)RH D111
1 (R) Yes
LH D110
PKIA5242E
Terminals
Continuity IPDM E/R Rear combination lamp
ConnectorTerminal
(Wire color)ConnectorTerminal
(Wire color)
E7 22 (R)RH B219
1 (R) Yes
LH B57
PKIA5243E
Page 3698 of 4449

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-143
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
6. CHECK GROUND
1. Turn ignition switch OFF.
2. Check continuity between front side maker lamp harness con-
nector and ground.
3. Check continuity between clearance lamp harness connector
and ground.
4. Check continuity between license plate lamp harness connector
and ground.
5. Check continuity between rear combination lamp harness con-
nector and ground.
OK or NG
OK >> Check bulb.
NG >> Repair harness or connector.
Terminals
Continuity Front side marker lamp
Ground Connector Terminal (Wire color)
RH E22
2 (B) Yes
LH E42
PKIA5244E
Te r m i n a l s
Continuity Clearance lamp
Ground Connector Terminal (Wire color)
RH E23
3 (B) Yes
LH E43
SKIA5881E
Terminals
Continuity License plate lamp
Ground Connector Terminal (Wire color)
RH D111
2 (B) Yes
LH D110
PKIA5246E
Te r m i n a l s
Continuity Rear combination lamp (Side marker)
Ground Connector Terminal (Wire color)
RH B219
2 (B) Yes
LH B57
PKIA5247E
Page 3699 of 4449

LT-144
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2004 November 2004 FX35/FX45
Tail Lamp Does Not OperateAKS007IN
1. CHECK STOP LAMP AND TURN SIGNAL LAMP
Make sure stop lamps and turn signal lamps are illuminated.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK INPUT SIGNAL
Check voltage between rear combination lamp control unit harness
connector B65 terminal 2 (R) and ground.
OK or NG
OK >> Replace rear combination lamp control unit.
NG >> Repair harness or connector.
3. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear combination lamp control unit connector.
3. Check voltage between rear combination lamp control unit har-
ness connector B65 terminal 1 (GY) and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4. CHECK GROUND CIRCUIT
Check continuity between rear combination lamp control unit har-
ness connector B65 terminal 7 (B) and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
Terminal
(-) Condition Voltage (+)
ConnectorTerminal
(Wire color)
B65 2 (R) GroundLighting switch 1ST
position is ON.Battery voltage
Lighting switch 1ST
position is OFF.Approx. 0
PKIA5248E
1 (GY) – Ground : Battery voltage should exist.
SKIA5907E
7 (B) – Ground : Continuity should exist.
SKIA5908E
Page 3700 of 4449

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-145
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
5. CHECK TURN SIGNAL LAMPS CIRCUIT
1. Disconnect rear combination lamp RH and LH connector.
2. Check continuity between rear combination lamp control unit
harness connector B65 terminal 11 (W) and rear combination
lamp LH harness connector B57 terminal 3 (W).
3. Check continuity between rear combination lamp control unit
harness connector B65 terminal 10 (BR) and rear combination
lamp LH harness connector B57 terminal 4 (BR).
4. Check continuity between rear combination lamp control unit
harness connector B65 terminal 9 (LG) and rear combination lamp RH harness connector B219 terminal 3
(LG).
5. Check continuity between rear combination lamp control unit harness connector B65 terminal 8 (Y) and
rear combination lamp RH harness connector B219 terminal 4 (Y).
OK or NG
OK >> Replace rear combination lamp control unit or rear combination lamp, and then check if turn signal
lamps is illuminated.
NG >> Repair harness or connector.
Parking, License Plate and Tail Lamps Do Not Turn OFF (After Approx. 10 Min-
utes)
AKS007E4
1. CHECK IPDM E/R
1. Turn ignition switch ON. Turn the combination switch (lighting switch) to the OFF position. Turn ignition
switch OFF.
2. Verify that the parking, license plate, and tail lamps turn ON and OFF after approximately 10 minutes.
OK or NG
OK >> Ignition relay malfunction. Refer to PG-19, "Function of Detecting Ignition Relay Malfunction" .
NG >> INSPECTION END
License Plate LampAKS007E5
BULB REPLACEMENT, REMOVAL AND INSTALLATION
1. Remove screws and remove license plate lamp from back door.
2. Disconnect license plate lamp connector.11 (W) – 3 (W) : Continuity should exist.
10 (BR) – 4 (BR) : Continuity should exist.
9 (LG) – 3 (LG) : Continuity should exist.
8 (Y) – 4 (Y) : Continuity should exist.
SKIA5910E
SKIA5567E
Page 3701 of 4449

LT-146
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2004 November 2004 FX35/FX45
3. Insert a flat head or suitable tool and remove housing.
4. Remove bulb from it's socket.
5. Install in the reverse order of removal.
Front Parking (Clearance) LampAKS007E6
BULB REPLACEMENT
For bulb replacement, refer to LT- 3 5 , "Bulb Replacement" in “HEAD LAMP-XENON TYPE-”.
REMOVAL AND INSTALLATION
For front parking (clearance) lamp removal and installation procedures, refer to LT- 3 6 , "Removal and Installa-
tion" in “HEAD LAMP -XENON TYPE-”.
Tail LampAKS007E7
BULB REPLACEMENT
For bulb replacement, refer to LT- 1 4 7 , "Bulb Replacement" in “REAR COMBINATION LAMP”.
REMOVAL AND INSTALLATION
For tail lamp removal and installation procedures, refer to LT- 1 4 7 , "Removal and Installation" in “REAR COM-
BINATION LAMP”.
Front Side Marker LampAKS007E8
BULB REPLACEMENT
For bulb replacement, refer to LT- 3 5 , "Bulb Replacement" in “HEAD LAMP-XENON TYPE-”.
REMOVAL AND INSTALLATION
For head lamp removal and installation procedures, refer to LT- 3 6 , "Removal and Installation" in “HEAD
LAMP-XENON TYPE-”.
Rear Side Marker LampAKS007E9
BULB REPLACEMENT
For bulb replacement, refer to LT- 1 4 7 , "Bulb Replacement" in “REAR COMBINATION LAMP”.
REMOVAL AND INSTALLATION
For rear side marker lamp removal and installation procedures, refer to LT- 1 4 7 , "Removal and Installation" in
“REAR COMBINATION LAMP”.
Rear Combination Lamp Control UnitAKS007O3
REMOVAL AND INSTALLATION
Refer to LT- 1 0 7 , "Removal and Installation of Rear Combination Lamp Control Unit" in “TURN SIGNAL AND
HAZARD WARNING LAMPS”.License plate lamp : 12V - 5W
SKIA5568E
Page 3702 of 4449

REAR COMBINATION LAMP
LT-147
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
REAR COMBINATION LAMPPFP:26554
Bulb ReplacementAKS007FP
REAR FENDER SIDE (REAR SIDE MARKER LAMP BULB)
1. Remove rear combination lamp.
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
BACK DOOR SIDE (BACK-UP LAMP)
1. Remove rear combination lamp.
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationAKS007FQ
REMOVAL
Rear Fender Side
1. Remove bumper side cover A. Refer to EI-18, "Removal and
Installation" in “EI” section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts.
4. Pull rear combination lamp toward side of the vehicle and
remove from the vehicle.
SKIA5569E
SKIA5570E
Stop/tail lamp (rear fender side) : LED (Replace together with rear combination
lamp assembly.)
Rear side marker lamp (rear fender side) : 12V - 3.8W
Back-up lamp (back door side) : 12V - 18W
Rear turn signal lamp (rear fender side) : LED (Replace together with rear combination
lamp assembly.)
SKIA5571E
Page 3703 of 4449
LT-148
REAR COMBINATION LAMP
Revision: 2004 November 2004 FX35/FX45
Trunk Lid Side
1. Remove back door finisher. Refer to EI-46, "Removal and Instal-
lation" in “EI” section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting nuts.
4. Remove rear combination lamp from back door.
5. Remove seal packing from back door.
INSTALLATION
Note the following, and install in the reverse order of removal.
Install a new seal packing to the rear combination lamp.
CAUTION:
Seal packing cannot be reused.
SKIA5572E
Rear combination lamp mounting nut : 3.2 N·m (0.33 kg-m, 28 in-lb)
Page 3704 of 4449
VANITY MIRROR LAMP
LT-149
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
VANITY MIRROR LAMPPFP:96400
Bulb ReplacementAKS007EC
1. Insert a thin screwdriver in the lens end and remove lens.
2. Remove bulb together with substrate.
3. Install in the reverse order of removal.Vanity mirror lamp : 12V - 1.32W
PKIA1137E