2004 INFINITI FX35 Service Manual

window inflation pressure jump cable trunk display reset sun roof

Load previous 8 pages

Page 1185 of 4449

INFINITI FX35 2004 Service Manual BRC-60
[VDC/TCS/ABS]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
Revision: 2004 November 2004 FX35/FX45
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)PFP:47660
Removal and InstallationAFS001Z5
REMOVAL
1. Disconnect

Page 1186 of 4449

INFINITI FX35 2004 Service Manual ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
BRC-61
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2004 November 2004 FX35/FX45
After installing vehicle harness connector in the actuator, make sure conn

Page 1187 of 4449

INFINITI FX35 2004 Service Manual BRC-62
[VDC/TCS/ABS]
G SENSOR
Revision: 2004 November 2004 FX35/FX45
G SENSORPFP:47930
Removal and InstallationAFS001TG
REMOVAL
1. Remove center console. Refer to IP-12, "(H) Center Console" .
2. Disc

Page 1188 of 4449

INFINITI FX35 2004 Service Manual STEERING ANGLE SENSOR
BRC-63
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2004 November 2004 FX35/FX45
STEERING ANGLE SENSORPFP:25554
Removal and InstallationAFS0021I
REMOVAL
1. Remove spiral ca

Page 1189 of 4449

INFINITI FX35 2004 Service Manual BRC-64
[VDC/TCS/ABS]
STEERING ANGLE SENSOR
Revision: 2004 November 2004 FX35/FX45

Page 1190 of 4449

INFINITI FX35 2004 Service Manual CO-1
ENGINE COOLING SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION CO
A
CO
Revision: 2004 November 2004 FX35/FX45
ENGINE COOLING SYSTEM
VQ35DE
PRECAUTIONS ....................................

CO-1
ENGINE COOLING SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION CO
A
CO
Revision: 2004 November 2004 FX35/FX45
ENGINE COOLING SYSTEM
VQ35DE
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Liquid Gasket .................................. 3
REMOVAL OF LIQUID GASKET SEALING .......... 3
LIQUID GASKET APPLICATION PROCEDURE ..... 3
PREPARATION ........................................................... 5
Special Service Tools ............................................... 5
Commercial Service Tools ........................................ 6
OVERHEATING CAUSE ANALYSIS .......................... 7
Troubleshooting Chart .............................................. 7
COOLING SYSTEM .................................................... 9
Cooling Circuit .......................................................... 9
System Drawing ..................................................... 10
ENGINE COOLANT ...................................................11
Inspection ................................................................ 11
LEVEL CHECK .................................................... 11
CHECKING COOLING SYSTEM FOR LEAKS .... 11
Changing Engine Coolant ....................................... 11
DRAINING ENGINE COOLANT .......................... 11
REFILLING ENGINE COOLANT ........................ 12
FLUSHING COOLING SYSTEM ......................... 13
RADIATOR ................................................................ 14
Removal and Installation ........................................ 14
REMOVAL ........................................................... 14
INSTALLATION ................................................... 15
INSPECTION AFTER INSTALLATION ............... 15
Checking Radiator Cap .......................................... 15
Checking Radiator .................................................. 16
RADIATOR (ALUMINUM TYPE) .............................. 17
Disassembly and Assembly ................................... 17
PREPARATION ................................................... 17
DISASSEMBLY ................................................... 17
ASSEMBLY ......................................................... 18
INSPECTION ...................................................... 20
COOLING FAN ......................................................... 21
Removal and Installation ........................................ 21
REMOVAL ........................................................... 21INSTALLATION ................................................... 21
Disassembly and Assembly .................................... 21
DISASSEMBLY ................................................... 21
ASSEMBLY ......................................................... 21
WATER PUMP .......................................................... 22
Removal and Installation ........................................ 22
REMOVAL ........................................................... 22
INSPECTION AFTER REMOVAL ....................... 24
INSTALLATION ................................................... 24
INSPECTION AFTER INSTALLATION ................ 25
WATER INLET AND THERMOSTAT ASSEMBLY .... 26
Removal and Installation ........................................ 26
REMOVAL ........................................................... 26
INSPECTION AFTER REMOVAL ....................... 27
INSTALLATION ................................................... 27
INSPECTION AFTER INSTALLATION ................ 27
WATER OUTLET AND WATER PIPING ................... 28
Removal and Installation ........................................ 28
REMOVAL ........................................................... 28
INSTALLATION ................................................... 28
INSPECTION AFTER INSTALLATION ................ 28
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 29
Standard and Limit .................................................. 29
ENGINE COOLANT CAPACITY (APPROXI-
MATE) .................................................................. 29
THERMOSTAT .................................................... 29
RADIATOR .......................................................... 29
VK45DE
PRECAUTIONS ........................................................ 30
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 30
PREPARATION ......................................................... 31
Special Service Tools ............................................. 31
Commercial Service Tools ...................................... 31
OVERHEATING CAUSE ANALYSIS ........................ 32
Troubleshooting Chart ............................................ 32

Page 1191 of 4449

INFINITI FX35 2004 Service Manual CO-2Revision: 2004 November 2004 FX35/FX45 COOLING SYSTEM .................................................. 34
Cooling Circuit ........................................................ 34
System Dra

CO-2Revision: 2004 November 2004 FX35/FX45 COOLING SYSTEM .................................................. 34
Cooling Circuit ........................................................ 34
System Drawing ..................................................... 35
ENGINE COOLANT .................................................. 36
Inspection ............................................................... 36
LEVEL CHECK .................................................... 36
LEAK CHECK ...................................................... 36
Changing Engine Coolant ....................................... 36
DRAINING ENGINE COOLANT .......................... 36
REFILLING ENGINE COOLANT ......................... 37
FLUSHING COOLING SYSTEM ......................... 38
RADIATOR ................................................................ 39
Removal and Installation ........................................ 39
REMOVAL ........................................................... 39
INSTALLATION .................................................... 41
INSPECTION AFTER INSTALLATION ................ 41
Checking Radiator Cap .......................................... 41
Checking Radiator .................................................. 41
RADIATOR (ALUMINUM TYPE) ............................... 43
Disassembly and Assembly .................................... 43
PREPARATION ................................................... 43
DISASSEMBLY ................................................... 43
ASSEMBLY ......................................................... 44
INSPECTION ....................................................... 46
COOLING FAN .......................................................... 47
Removal and Installation (Crankshaft Driven Type) ... 47
REMOVAL ........................................................... 47
INSPECTION AFTER REMOVAL ........................ 47INSTALLATION .................................................... 47
Removal and Installation (Motor Driven Type) ........ 48
REMOVAL ............................................................ 48
INSTALLATION .................................................... 48
Disassembly and Assembly (Motor Driven Type) ... 48
DISASSEMBLY .................................................... 48
INSPECTION AFTER DISASSEMBLY ................ 48
ASSEMBLY .......................................................... 48
WATER PUMP ........................................................... 49
Removal and Installation ......................................... 49
REMOVAL ............................................................ 49
INSPECTION AFTER REMOVAL ........................ 49
INSTALLATION .................................................... 50
INSPECTION AFTER INSTALLATION ................ 50
THERMOSTAT AND WATER CONTROL VALVE ..... 51
Removal and Installation ......................................... 51
REMOVAL ............................................................ 51
INSPECTION AFTER REMOVAL ........................ 52
INSTALLATION .................................................... 52
INSPECTION AFTER INSTALLATION ................ 53
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 54
Standard and Limit .................................................. 54
ENGINE COOLANT CAPACITY (APPROXI-
MATE) .................................................................. 54
RADIATOR ........................................................... 54
THERMOSTAT ..................................................... 54
WATER CONTROL VALVE .................................. 54

Page 1192 of 4449

INFINITI FX35 2004 Service Manual PRECAUTIONS
CO-3
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: 2004 November 2004 FX35/FX45
[VQ35DE]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
B

PRECAUTIONS
CO-3
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: 2004 November 2004 FX35/FX45
[VQ35DE]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ABS009A8
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Liquid GasketABS005ZR
REMOVAL OF LIQUID GASKET SEALING
After removing mounting bolts and nuts, separate the mating
surface using a seal cutter (SST) and remove old liquid gasket
sealing.
CAUTION:
Be careful not to damage the mating surfaces.
Tap seal cutter to insert it, and then slide it by tapping on the
side as shown in the figure.
In areas where seal cutter is difficult to use, use plastic hammer
to lightly tap the areas where the liquid gasket is applied.
CAUTION:
If for some unavoidable reason tool such as screwdriver is
used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using a scraper, remove old liquid gasket adhering to the liquid
gasket application surface and the mating surface.
Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.
2. Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
PBIC0002E
PBIC0003E

Load next 8 pages

Page: < prev 1-10 ... 1153-1160 1161-1168 1169-1176 1177-1184 1185-1192 1193-1200 1201-1208 1209-1216 1217-1224 ... 4456 next >

cabin filter oil viscosity brake pads jump cable timing belt manual radio set