Page 3705 of 4449
LT-150
MAP LAMP
Revision: 2004 November 2004 FX35/FX45
MAP LAMPPFP:26430
Bulb ReplacementAKS007ED
1. Remove lens using clip driver or suitable tool.
2. Remove bulb.
3. Install in the reverse order of removal.
Removal and InstallationAKS007EE
REMOVAL
1. Insert a clip driver or suitable tool back of map lamp and pull
down it to disengage metal clip.
2. Pull down map lamp in direction shown by the arrow in the fig-
ure.
3. Disconnect map lamp connector and remove map lamp.
INSTALLATION
Install in the reverse order of removal.Map lamp : 12V - 8 W
PKIA2846E
PKIA2847E
Page 3706 of 4449
PERSONAL LAMP
LT-151
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
PERSONAL LAMPPFP:26415
Bulb ReplacementAKS007FT
1. Remove personal lamp. Refer to LT- 1 5 1 , "Removal and Installa-
tion" .
2. Remove screw from personal lamp.
3. Insert a screwdriver or similar tool and remove lens.
4. Remove bulb.
5. Install in the reverse order of removal.
Removal and InstallationAKS007FU
REMOVAL
1. Use a clip driver or similar tool to press metal clip, and remove personal lamp.
2. Disconnect personal lamp connector.
INSTALLATION
Install in the reverse order of removal.Personal lamp : 12V - 8W
SKIA5577E
SKIA5578E
Page 3707 of 4449
LT-152
LUGGAGE ROOM LAMP
Revision: 2004 November 2004 FX35/FX45
LUGGAGE ROOM LAMPPFP:26410
Bulb ReplacementAKS007FV
1. Remove luggage room lamp. Refer to LT- 1 5 2 , "Removal and
Installation" .
2. Remove screw from luggage room lamp.
3. Insert a suitable tool and remove lens.
4. Remove bulb.
5. Install in the reverse order of removal.
Removal and InstallationAKS007FW
REMOVAL
1. Use a clip driver or similar tool to press metal clip, and remove luggage room lamp.
2. Disconnect luggage room lamp connector.
INSTALLATION
Install in the reverse order of removal.Luggage room lamp : 12V - 8W
SKIA6197E
SKIA5579E
Page 3708 of 4449
IGNITION KEY HOLE ILLUMINATION
LT-153
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
IGNITION KEY HOLE ILLUMINATIONPFP:48476
Bulb Replacement, Removal and InstallationAKS007FR
1. Remove combination meter. Refer to DI-26, "Removal and
Installation" in “DI” section.
2. Remove screw and remove NATS antenna amp.
3. Pull out ring and turn bulb socket to left to release lock.
4. Install in the reverse order of removal.Key cylinder illumination : 12V - 1.4W
SKIA5575E
Page 3709 of 4449
LT-154
GLOVE BOX LAMP
Revision: 2004 November 2004 FX35/FX45
GLOVE BOX LAMPPFP:68520
Bulb Replacement, Removal and InstallationAKS007FS
1. Remove instrument passenger lower panel. Refer to IP-13, "(J)
Instrument Passenger Lower Panel" in “IP” section.
2. Turn bulb socket left to release lock and remove it.
3. Install in the reverse order of removal.Glove box lamp : 12V - 1.4W
SKIA5576E
Page 3710 of 4449
ASHTRAY ILLUMINATION
LT-155
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
ASHTRAY ILLUMINATIONPFP:25860
Bulb Replacement and Removal and InstallationAKS007NZ
1. Remove A/T console finisher. Refer to IP-12, "(F) A/T Console Finisher" in “IP” section.
2. Remove instrument ashtray and hazard switch. Refer to IP-17,
"A/T CONSOLE FINISHER" in “IP” section.
3. Use a screwdriver to undo ashtray finisher hooks.
4. Turn bulb socket on circuit board to left to undo lock. Remove
bulb socket.
5. Install in the reverse order of removal.
Ashtray and cigarette
lighter illumination: 12V - 1.4W
PKIA2850E
Page 3711 of 4449
LT-156
CIGARETTE LIGHTER ILLUMINATION
Revision: 2004 November 2004 FX35/FX45
CIGARETTE LIGHTER ILLUMINATIONPFP:25331
Bulb Replacement and Removal and InstallationAKS007O0
Refer to LT- 1 5 5 , "Bulb Replacement and Removal and Installation" in “ASHTRAY ILLUMINATION”.
Page 3712 of 4449

INTERIOR ROOM LAMP
LT-157
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
INTERIOR ROOM LAMPPFP:26410
Component Parts and Harness Connector LocationAKS007O8
System DescriptionAKS007F7
When room lamp and personal lamp switch is in DOOR position, room lamp and personal lamp ON/OFF is
controlled by timer according to signals from switches including key switch, front door switch driver side,
unlock signal from keyfob, door lock and unlock switch, key cylinder lock and unlock switch, ignition switch.
When room lamp and personal lamp turns ON, there is a gradual brightening over 1 second. When room lamp
and personal lamp turns OFF, there is a gradual dimming over 1 second.
The room lamp and personal lamp timer is controlled by the BCM (body control module).
Room lamp and personal lamp timer control settings can be changed with CONSULT-II.
Ignition keyhole illumination turns ON at time when driver door is opened (door switch ON) or removed keyfob
from key cylinder. Illumination turns OFF when driver door is closed (door switch OFF).
Step lamp turns ON at time when driver door or passenger door is opened (door switch ON). Lamp turns OFF
when driver, passenger doors are closed (all door switches OFF).
POWER SUPPLY AND GROUND
Power is supplied at all times (without intelligent key system)
through 15A fuse [No. 22, located in fuse block (J/B)]
to key switch terminal 2 and
to BCM (body control module) terminal 42
through 50A fusible link [letter M, located in fuse and fusible link block]
to BCM (body control module) terminal 55.
Power is supplied at all times (with intelligent key system)
through 10A fuse [No.38, located in fuse and fusible link block]
to key switch and ignition knob switch terminals 1
through 15A fuse [No.22, located in fuse block (J/B)]
to BCM (body control module) terminal 42
to key switch and ignition knob switch terminal 3, and
to key switch terminal 2
through 50A fusible link [letter M, located in fuse and fusible link block]
to BCM (body control module) terminal 55.
When the key plate inserted to key switch, power is supplied (without intelligent key system)
through the key switch terminal 1
to BCM (body control module) terminal 37.
PKIA2923E