2001 CHRYSLER VOYAGER Service Manual

handbrake lug pattern auxiliary battery traction control cooling wiper fluid

Page 833 of 4284

CHRYSLER VOYAGER 2001 Service Manual TEST ACTION APPLICABILITY
4 Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between ground and the Liftgate Full Open Switch Sense
circuit.
Open the liftgate completely then

TEST ACTION APPLICABILITY
4 Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between ground and the Liftgate Full Open Switch Sense
circuit.
Open the liftgate completely then partially close it. Repeat this step while observing
the ohmmeter.
Did the resistance change from below 15 ohms to above 1000.0 ohms when door was
partially closed?All
Ye s®Replace the Power Liftgate Module.
Perform BODY VERIFICATION TEST - VER 1.
No®Go To 5
5 Disconnect the Power Liftgate C2 connector.
Disconnect the Full Open Switch connector.
Measure the resistance of the Ground wire between the PLG C2 connector (cavity 20)
and the Full Open Switch connector.
Wiggle the harness while observing the ohmmeter.
Is the resistance below 5.0 ohms?All
Ye s®Go To 6
No®Repair the Ground wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
6 Disconnect the Power Liftgate Module C2 connector.
Disconnect the Power Liftgate Motor connector.
Measure the resistance of the Liftgate Full Open Switch Sense wire between the
Power Liftgate Module C2 connector and the Power Liftgate Motor connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 7
No®Repair the Liftgate Full Open Switch Sense wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
7 Disconnect the Power Liftgate Module C2 connector.
Disconnect the Power Liftgate Motor connector.
Measure the resistance between ground and the Liftgate Full Open Switch Sense
circuit.
Is the resistance below 1000.0 ohms?All
Ye s®Repair the Liftgate Full Open Switch Sense wire for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No®Go To 8
8 Disconnect the Power Liftgate Module C2 connector.
Disconnect the Power Liftgate Motor connector.
Measure the resistance between the Ground circuit and the Liftgate Full Open
Switch Sense circuit.
Is the resistance below 1000.0 ohms?All
Ye s®Repair the Liftgate Full Open Switch Sense wire for a short to the
Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.
No®Go To 9
804
POWER DOORS - LIFTGATE
INCOMPLETE POWER OPEN - LATCH FAILURE ÐContinued

Page 834 of 4284

CHRYSLER VOYAGER 2001 Service Manual TEST ACTION APPLICABILITY
9 If there are no possible causes remaining, view repair. All
Repair
Replace the Power Liftgate Motor assembly.
Perform BODY VERIFICATION TEST - VER 1.
10 Disconnect the Powe

Page 835 of 4284

CHRYSLER VOYAGER 2001 Service Manual TEST ACTION APPLICABILITY
14 Disconnect the Power Liftgate Module C2 connector.
NOTE: The Liftgate Ajar Switch Sense circuit is also the Ratchet Switch
Sense circuit for the liftgate.
Measure the resi

TEST ACTION APPLICABILITY
14 Disconnect the Power Liftgate Module C2 connector.
NOTE: The Liftgate Ajar Switch Sense circuit is also the Ratchet Switch
Sense circuit for the liftgate.
Measure the resistance between the Ground circuit and the Liftgate Ajar Switch
Sense circuit.
Open the Liftgate completely.
Using a screwdriver, close the latch to the second detent while observing the
ohmmeter.
Release the latch with the handle. Repeat this step while observing the ohmmeter.
Did the resistance change from below 15 ohms to above 1000.0 ohms when the latch
changed states?All
Ye s®Replace the Power Liftgate Module.
Perform BODY VERIFICATION TEST - VER 1.
No®Go To 15
15 Disconnect the Power Liftgate C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance of the Ground wire between the PLG C2 connector (cavity 20)
and the Liftgate Cinch/Release Motor connector (cavity 1).
Wiggle the harness while observing the ohmmeter.
Is the resistance below 5.0 ohms?All
Ye s®Go To 16
No®Repair the Ground wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
16 Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance of the Liftgate Ajar Switch Sense wire between the Power
Liftgate Module C2 connector and the Liftgate Cinch/Release Motor connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 17
No®Repair the Liftgate Ajar Switch Sense wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
17 If there are no possible causes remaining, view repair. All
Repair
Replace the Liftgate Cinch Release Motor.
Perform BODY VERIFICATION TEST - VER 1.
18 Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between the Liftgate Latch Cinch Driver circuit and the
Liftgate Latch Release Driver circuit.
Wiggle the harness and check for an intermittent open condition.
Is the resistance below 2.0 ohms?All
Ye s®Go To 19
No®Go To 21
806
POWER DOORS - LIFTGATE
INCOMPLETE POWER OPEN - LATCH FAILURE ÐContinued

Page 836 of 4284

CHRYSLER VOYAGER 2001 Service Manual TEST ACTION APPLICABILITY
19 Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between the Ground circuit and the Liftgate Latch Cinch
Driver circuit.
Wi

TEST ACTION APPLICABILITY
19 Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between the Ground circuit and the Liftgate Latch Cinch
Driver circuit.
Wiggle the harness and check for an intermittent short to the Ground circuit
condition.
Is the resistance below 100.0 ohms?All
Ye s®Repair the Liftgate Latch Cinch Driver circuit for a short to the
Ground circuit. This could be the Liftgate Latch Cinch Driver or
Liftgate Latch Release Driver or the motor itself.
Perform BODY VERIFICATION TEST - VER 1.
No®Go To 20
20 Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between ground and the Liftgate Latch Cinch Driver circuit.
Wiggle the harness and check for an intermittent short to ground condition.
Is the resistance below 100.0 ohms?All
Ye s®Repair the Liftgate Latch Cinch Driver circuit for a short to
ground. This could be the Liftgate Latch Cinch Driver or Liftgate
Latch Release Driver or the motor itself.
Perform BODY VERIFICATION TEST - VER 1.
No®Replace the Liftgate Cinch Release Motor.
Perform BODY VERIFICATION TEST - VER 1.
21 Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance of the Liftgate Latch Cinch Driver circuit between the Power
Liftgate Module C2 connector and the Liftgate Cinch/Release Motor connector.
Wiggle the harness and check for an intermittent open condition.
Is the resistance below 5.0 ohms?All
Ye s®Go To 22
No®Repair the Liftgate Latch Cinch Driver wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
22 Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance of the Liftgate Latch Release Driver circuit between the
Power Liftgate Module C2 connector and the Liftgate Cinch/Release Motor connector.
Wiggle the harness and check for an intermittent open condition.
Is the resistance below 5.0 ohms?All
Ye s®Go To 23
No®Repair the Liftgate Latch Release Driver wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
23 If there are no possible causes remaining, view repair. All
Repair
Replace the Liftgate Cinch Release Motor.
Perform BODY VERIFICATION TEST - VER 1.
807
POWER DOORS - LIFTGATE
INCOMPLETE POWER OPEN - LATCH FAILURE ÐContinued

Page 837 of 4284

CHRYSLER VOYAGER 2001 Service Manual Symptom:
INCOMPLETE POWER OPEN - MISSING HALL SIGNAL
When Monitored and Set Condition:
INCOMPLETE POWER OPEN - MISSING HALL SIGNAL
When Monitored: During Power Liftgate opening cycle.
Set Condition: I

Page 838 of 4284

CHRYSLER VOYAGER 2001 Service Manual TEST ACTION APPLICABILITY
2 Examine the liftgate for proper alignment, worn or binding hinges, weak liftgate prop
assembly, loose/ hard weatherstrip, and gear teeth on the Power Liftgate Motor
assembl

TEST ACTION APPLICABILITY
2 Examine the liftgate for proper alignment, worn or binding hinges, weak liftgate prop
assembly, loose/ hard weatherstrip, and gear teeth on the Power Liftgate Motor
assembly for wear or anything that would cause an obstruction to proper operation.
If necessary manually operate the power liftgate on a known good vehicle and notice
the effort needed to open and close for comparison.
Especially notice the effort needed to unlatch and close the liftgate.
Were there any mechanical problems found?All
Ye s®Refer to Service information for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
No®Go To 3
3 Operate the liftgate from the full closed position and put an obstacle in it's path to
make it reverse.
Did the door reverse back to the closed position?All
Ye s®Go To 4
No®Replace the Power Liftgate Module.
Perform BODY VERIFICATION TEST - VER 1.
4 Disconnect the Power Liftgate Motor connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit.
Does the test light illuminate brightly?All
Ye s®Go To 5
No®Repair the hall effect ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
5 Disconnect the Power Liftgate Motor connector.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance of the Liftgate Hall Effect Supply circuit between the Power
Liftgate Motor connector and the Power Liftgate Module C2 connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 6
No®Repair the Liftgate Hall Effect Supply wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
6 Disconnect the Power Liftgate Motor connector.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between ground and the Liftgate Hall Effect Supply circuit.
Is the resistance below 100.0 ohms?All
Ye s®Repair the Door Motor Hall Effect Supply wire for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No®Go To 7
809
POWER DOORS - LIFTGATE
INCOMPLETE POWER OPEN - MISSING HALL SIGNAL ÐContinued

Page 839 of 4284

CHRYSLER VOYAGER 2001 Service Manual TEST ACTION APPLICABILITY
7 Disconnect the Power Liftgate Motor connector.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between the Ground circuit (cavity 20) and the Lift

Page 840 of 4284

CHRYSLER VOYAGER 2001 Service Manual Symptom:
INCOMPLETE POWER OPEN - OVERCURRENT
When Monitored and Set Condition:
INCOMPLETE POWER OPEN - OVERCURRENT
When Monitored: Anytime the Power Liftgate is in a power open operation.
Set Conditio

Load next 8 pages

Page: < prev 1-10 ... 801-808 809-816 817-824 825-832 833-840 841-848 849-856 857-864 865-872 ... 4288 next >

clock reset key battery check engine manual transmission tires wheel bolts