Page 2369 of 3066
INSTRUMENT PANEL ASSEMBLY
IP-3
C
D
E
F
G
H
J
K
L
MA
B
IP
INSTRUMENT PANEL ASSEMBLYPFP:68200
Component Parts DrawingEIS000NH
SIIA0225E
Page 2370 of 3066
IP-4
INSTRUMENT PANEL ASSEMBLY
1 Front passenger air bag module 2 Front speaker grille (left) 3 Front side speaker (left)
4 Cup holder (left) 5 Instrument finisher B 6 Combination meter
7 Instrument mask (left) 8 GPS antenna 9 Instrument mask (right)
10 Instrument cluster lid A 11 Pocket 12 Front speaker grille (right)
13 Front side speaker (right) 14 Cup holder (right) 15 Mirror control switch
16 Instrument panel & pad 17 Instrument reinforcement 18 Audio unit and pocket
19 Glove box cover 20 Lower instrument panel 21 Glove box pin
22 Glove box 23 Cluster lid C 24 Instrument finisher A
25 Instrument lower driver panel 26 Column cover, key cylinder escutcheon 27 Cluster lid finisher (right)
28 Heater control finisher 29 CD auto–changer and pocket 30 instrument lower center panel
31 Lower instrument cover 32 Cluster lid finisher (left) 33 Center console
34 A/T or M/T finisher 35 Console mask 36 Seal case (inner case)
Page 2371 of 3066
![NISSAN X-TRAIL 2003 Electronic Repair Manual INSTRUMENT PANEL ASSEMBLY
IP-5
C
D
E
F
G
H
J
K
L
MA
B
IP
Removal and InstallationEIS0 00 NI
TA B L E O F W O R K I T E M
[ ]: The number shows the removal order.
ComponentsInstrument
panelCombination
NISSAN X-TRAIL 2003 Electronic Repair Manual INSTRUMENT PANEL ASSEMBLY
IP-5
C
D
E
F
G
H
J
K
L
MA
B
IP
Removal and InstallationEIS0 00 NI
TA B L E O F W O R K I T E M
[ ]: The number shows the removal order.
ComponentsInstrument
panelCombination](/manual-img/5/57402/w960_57402-2370.png)
INSTRUMENT PANEL ASSEMBLY
IP-5
C
D
E
F
G
H
J
K
L
MA
B
IP
Removal and InstallationEIS0 00 NI
TA B L E O F W O R K I T E M
[ ]: The number shows the removal order.
ComponentsInstrument
panelCombination
meterNavigation
DisplayAudio
Console
Up Down
Front speaker grille [1]
Instrument finisher A, B [2] [1]
Cup holder [3]
Instrument cluster lid A [4] [2]
Combination meter [5] [3]
Pocket [6]
Key cylinder escutcheon and steer-
ing column cover[7]
Instrument lower driver panel [8]
Mirror control switch [9]
GPS antenna [10]
Cluster lid C [11] [1] [1]
Audio unit and pocket [12] [2] [2]
Cluster lid finisher [13] [1] [1]
Heater control finisher [14] [2]
CD auto–changer and pocket [15] [3]
Heater controller [16]
A/T(M/T,CVT) finisher [17] [2]
Console mask [18] [3]
Center console [19] [4]
Lower instrument cover [20]
instrument lower center panel [21]
Glove box [22]
Lower instrument panel [23]
Glove box cover [24]
Front passenger air bag module [25]
Instrument reinforcement [26]
Instrument mask [27]
Front pillar garnish [28]
Instrument panel [29]
Page 2372 of 3066
IP-6
INSTRUMENT PANEL ASSEMBLY
FRONT SPEAKER GRILLE
lPull forward and remove.
INSTRUMENT FINISHER
lRemove clips starting from the outside.
CUP HOLDER
lUndo and remove screws.
CLUSTER LID A
lRemove screws, and pull instrument cluster lid A forward to
unfasten clip.
COMBINATION METER
lRemove screws, and remove connector. Then remove combination meter.
GPS ANTENNA
lUndo screws. Disconnect and remove connector.
POCKET
lUndo and remove screws.
STEERING COLUMN COVER
lRemove key cylinder escutcheon first. Remove screws.
SIIA0226E
SIIA0227E
SIIA0228E
Page 2373 of 3066
INSTRUMENT PANEL ASSEMBLY
IP-7
C
D
E
F
G
H
J
K
L
MA
B
IP
INSTRUMENT LOWER DRIVER PANEL
lRemove screws, and pull driver-side instrument lower panel
straight forward to unfasten the clip.
MIRROR CONTROL SWITCH
1. From the back, press tab on mirror control switch to remove. Or insert a screwdriver, wrapped with a shop
cloth, into lower side of the switch to unfasten the lower clip.
2. Disconnect and remove connector.
CLUSTER LID C
1. Open LH lid. Remove inner case and then bolts in drink box.
2. Insert a clip remover or similar tool into lower side of cluster lid C
and unfasten clip.
3. Unfasten and remove resin tabs on upper and lower sides.
AUDIO UNIT AND POCKET
Remove mounting screws on audio unit and pocket.Disconnect and remove connector.
NOTE:
During removal or installation, use shop cloth to protect surrounding area from damage.
CLUSTER LID FINISHER
lInsert a clip clamp remover or similar tool into center panel gap
and unfasten clip.
SIIA0230E
SIIA0229E
SIIA0231E
Page 2374 of 3066
IP-8
INSTRUMENT PANEL ASSEMBLY
A/T OR M/T FINISHER
1. Insert a screwdriver, wrapped with a shop cloth, into cutout on
rear edge of finisher, and lift up to unfasten clip on rear edge of
side face.
2. Pull forward and remove.
CENTER CONSOLE
1. Remove screws.
2. Remove console mask, and remove center console.
CD AUTO–CHANGER AND POCKET
lRemove screws. Disconnect and remove connector.
NOTE:
During removal or installation, use shop cloth to protect surrounding area from damage.
HEATER CONTROL FINISHER
lInsert a screwdriver or similar tool, wrapped with a shop cloth,
into lower edge (clip position). Unfasten and remove clip.
HEATER CONTROLLER
lRemove mounting screws on heater controller.Disconnect remove connector.
LOWER INSTRUMENT COVER
lUnfasten resin clips, and pull toward vehicle rear.
INSTRUMENT LOWER CENTER PANEL
lUndo and remove screws.
SIIA0233E
SIIA0235E
SIIA0236E
Page 2375 of 3066
INSTRUMENT PANEL ASSEMBLY
IP-9
C
D
E
F
G
H
J
K
L
MA
B
IP
GLOVE BOX
lOpen glove box, and remove glove box pin from inside.
LOWER INSTRUMENT PANEL
lPull clips forward from instrument reinforcement, and then
remove tab inside instrument lower panel from lower edge of
blower unit.
GLOVE BOX COVER
1. Remove screws.
2. Pull straight forward to remove from steering member bracket.
FRONT PASSENGER AIR BAG MODULE
lRemove mounting bolts. Remove front passenger air bag module. Refer toSRS-33, "FRONT PASSEN-
GER AIR BAG MODULE".
INSTRUMENT MASK
lInsert a slotted screwdriver, wrapped with a shop cloth, into cutout on the instrument mask. Unfasten and
remove tab.
FRONT PILLAR GARNISH
lPull front pillar garnish straight forward to inner side of vehicle. Unfasten and remove metal clip.
Refer toEI-26, "
BODY SIDE TRIM".
INSTRUMENT PANEL
1. Remove key interlock cable. Refer toAT-452, "KEY INTERLOCK CABLE".
PIIA0545E
SIIA0237E
SIIA0238E
Page 2376 of 3066
IP-10
INSTRUMENT PANEL ASSEMBLY
2. Remove nuts, and lower steering column.
3. Remove bolts, nuts and screw from the instrument panel, and
remove the instrument panel.
NOTE:
When installing, check that the locating pin on back of the instrument
panel is completely seated in locating hole on body.
Disassembly and AssemblyEIS001O0
CONSOLE BOX ASSEMBLY
1. Remove console lid.
2. Remove mounting screws on console bracket.
3. Remove mounting screws on console side bracket (RH/LH) and console box.
4. Remove mounting screws on console finisher.
SIIA0040E
SIIA0239E
PIIA0565E