Page 617 of 3039
8.
9. CAUTIONS:
Make sure that the road wheels are in the straight
ahead position.
Make sure that excessive force is not used. Failure to
follow this instruction may result in damage to the vehicle.
Make sure that the brake hose is not twisted and is
correctly located.
Pull downwards at the position shown.
10. Refer to: Brake System Bleeding (206-00 Brake System - General Information, General Procedures).
11. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
Page 618 of 3039
Published: 11-May-2011
Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake Disc Vehicles With: High Performance Brakes
Removal and Installation
Removal
CAUTION: Brake discs must be renewed in pairs.
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.
2. Refer to: Brake Pads - Vehicles With: High Performance Brakes (206-03B Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol,
Removal and Installation).
3. Torque: 115 Nm 4.
Remove the 2 clips.
Clean the components mating faces.
Installation 5. Repeat the above procedure on the opposite side.
1. To install, reverse the removal procedure.
Page 619 of 3039
Published: 11-May-2011
Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake Pads Vehicles With: High Performance Brakes
Removal and Installation
Removal
CAUTION: Brake fluid will damage paint finished surfaces. If spilled, immediately remove the fluid and clean the area
with water.
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.
2. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
3.
Page 620 of 3039
4. NOTE: Left-hand shown, right-hand similar.
5.
6. CAUTION: Removal of the clips is a delicate
procedure, damage will occur if any force is used.
NOTE: Left-hand shown, right-hand similar.
Lever the anti-rattle spring in the center of the
spring until either side is released.
Page 621 of 3039
7. WARNING: If the brake caliper piston seal is damaged
a new brake caliper must be installed.
CAUTION: Do not allow the brake caliper to hang on
the brake hose.
NOTE: Left-hand shown, right-hand similar.
8. NOTE: Left-hand shown, right-hand similar.
Release the clip.
9. NOTE: Left-hand shown, right-hand similar.
Page 622 of 3039
10.
11.
Repeat the above procedure on the opposite side.
Installation
1. WARNING: Do not use compressed air to clean brake components.
Dust from friction materials can be harmful if inhaled.
CAUTION: As the piston is pushed back into the caliper housing,
the brake fluid level in the reservoir will rise. Do not allow the reservoir
to overflow.
Press the piston into the caliper housing.
2.
Page 623 of 3039
3.
Apply grease C2C-39930 to the areas indicated.
4. NOTE: Left-hand shown, right-hand similar.
5. NOTE: Left-hand shown, right-hand similar. www.JagDocs.com
Page 624 of 3039
7. NOTE: Left-hand shown, right-hand similar.
Secure the bottom arm of the anti-rattle spring
under the bottom anchor bracket of the caliper.
Compress the upper spring arm into the correct
position, under the upper anchor bracket, whilst
retaining the logo plate.
Using the screw-driver, tap the central locating tag
into the locked position.