Page 345 of 3039
Page 346 of 3039
11.
12.
13.
14. Release the front lower arm.
Remove and discard the nut and bolt.
CAUTION: Prevent the rear lower arm ball joint ball pin
hexagon from rotating. Failure to follow this instruction may
result in damage to the lower ball joint boot.
Loosen the rear lower arm ball joint retaining nut.
CAUTION: Prevent the rear lower arm ball joint ball pin
hexagon from rotating. Failure to follow this instruction may
result in damage to the lower ball joint boot.
Adjust the rear lower arm ball joint retaining nut until the ball
joint thread cannot be seen.
WARNING: Make sure the special tool is supported while
carrying out the operation. Failure to follow this instruction
may result in personal injury.
CAUTIONS:
Make sure the special tool is supported while carrying out
the operation. Failure to follow this instruction may result in
damage to the special tool.
Make sure the special tool is correctly located and the
lower ball joint boot is not damaged while carrying out the
operation. Failure to follow this instruction may result in
damage to the component.
Using the special tool, release the rear lower arm ball joint
from the wheel knuckle lower pivot.
Tighten the special tool adjusting bolt to a maximum of
Page 347 of 3039
60 Nm.
If the rear lower arm ball joint releases from the wheel
knuckle lower pivot, using no more than 60 Nm on the
special tool adjusting bolt, proceed to step 13.
If the rear lower arm ball joint does not release from
the wheel knuckle lower pivot, using no more than 60
Nm on the special tool adjusting bolt, proceed to step
12.
15. WARNING: Make sure the special tool is supported while
carrying out the operation. Failure to follow this instruction
may result in personal injury.
CAUTIONS:
Make sure the special tool is supported while carrying out
the operation. Failure to follow this instruction may result in
damage to the special tool.
Make sure the special tool is correctly located and the
lower ball joint boot is not damaged while carrying out the
operation. Failure to follow this instruction may result in
damage to the component.
NOTE: Do not carry out this step if the rear lower arm
ball joint released from the wheel knuckle lower pivot in step
12.
Using the special tool, release the rear lower arm ball joint
from the wheel knuckle lower pivot.
Tighten the special tool adjusting bolt to a maximum of
60 Nm.
Strike the top surface of the special tool directly above
the rear lower arm ball joint at the point indicated
using a copper mallet.
16. CAUTION: Prevent the rear lower arm ball joint ball pin
hexagon from rotating. Failure to follow this instruction may
result in damage to the lower ball joint boot.
Remove the rear lower arm.
Remove and discard the retaining nut.
Page 348 of 3039
Installation
1. WARNING: Make sure that a new lower arm ball joint nut
is installed.
CAUTION: Prevent the rear lower arm ball joint ball pin
hexagon from rotating. Failure to follow this instruction may
result in damage to the lower ball joint boot.
Install the rear lower arm.
Tighten the nut to 92 Nm.
2. NOTE: Install a new retaining nut and bolt.
Secure the front lower arm.
Stage 1: Tighten to 60 Nm.
Stage 2: Tighten to a further 135 degrees.
3. Secure the rear lower arm.
Install the rear lower arm inner retaining nut, but do
not tighten fully at this stage.
4. Install the shock absorber and spring assembly.
Tighten the bolt to 175 Nm. www.JagDocs.com
Page 349 of 3039
5. Remove and discard the retaining straps.
6. Install the steering gear.
Tighten the bolts to 100 Nm.
7. Secure the tie rod end.
Tighten the nut to 55 Nm.
8. Install the stabilizer bar link.
For additional information, refer to: Front Stabilizer Bar Link (204-01 Front Suspension, Removal and Installation).
9. Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
10. Lower the body.
11. CAUTION: The final tightening of the upper arm must be
carried out with the vehicle on it's wheels.
Tighten to 175 Nm.
12.
Install the engine undertray.
For additional information, refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).
13. Using only four-wheel alignment equipment approved by Jaguar, check
Page 350 of 3039
(204-00 Suspension System - General Information, General Procedures).
Page 351 of 3039
Front Suspension - Rear Lower Arm Bushing
Removal and Installation
Special Tool(s)
Rear lower arm bushing remover and installer
204-464
Rear lower arm bushing remover
204-333
Rear lower arm bushing installer
204-332
Rear lower arm bushing installer
204-465
Rear lower arm bushing installer
204-334
Removal
CAUTION: Nuts and bolts must be tightened with the weight of the vehicle on the suspension. Published: 11-May-2011
1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.
2. Remove the rear lower arm.
For additional information, refer to: Rear Lower Arm (204-01 Front Suspension, Removal and Installation).
Page 352 of 3039
3. NOTE: Note the fitted position.
Using the special tools, remove and discard the lower arm rear
bushings.
Installation
1. Install the special tools to the rear lower arm.
Tighten the bolts.
2. NOTE: Align to the position noted on removal.
Position the bushing in the special tool.
3. Using the special tools, partially install the lower arm bushing.