2010 JAGUAR XFR Workshop Manual

transmission 4WD fuel cap oil change parking brake boot

Page 217 of 3039

JAGUAR XFR 2010 1.G Workshop Manual
DTC Description Possible Causes Action prior approval programme is in operation, prior to
the installation of a new module/component P0606-00
Control Module
Processor - No sub type
informatio

DTC Description Possible Causes Action prior approval programme is in operation, prior to
the installation of a new module/component P0606-00
Control Module
Processor - No sub type
information
Watchdog reset - internal
control module failure
This is a control module internal check DTC. If no
other DTCs are logged and no customer complaint
exists, clear/ignore this DTC. If the problem
persists, renew the control module. Refer to the
warranty policy and procedures manual, or
determine if any prior approval programme is in
operation, prior to the installation of a new
module/component P0607-00
Control Module
Performance - No sub
type information
Rear differential control
module internal error -
charge pump voltage
below threshold
Clear the DTC and retest. If the problem persists,
renew the control module. Refer to the warranty
policy and procedures manual, or determine if any
prior approval programme is in operation, prior to
the installation of a new module/component P0652-00
Sensor Reference
Voltage B Circuit Low -
No sub type
information
Position sensor supply
below 5.7V
Sensor failure (within
actuator)
Refer to the electrical circuit diagrams and check
the differential actuator sensor position circuit,
repair as necessary. Clear the DTC and retest
If no circuit problems exist, renew the differential
actuator. Refer to the warranty policy and
procedures manual, or determine if any prior
approval programme is in operation, prior to the
installation of a new module/component P0653-00
Sensor Reference
Voltage B Circuit High -
No sub type
information
Motor position sensor
supply above 8.3 V
Internal control module
failure
Refer to the electrical circuit diagrams and check
the differential actuator hall sensor reference
voltage at the control module or the actuator
If voltage is too high, then renew control module.
Refer to the warranty policy and procedures
manual, or determine if any prior approval
programme is in operation, prior to the installation
of a new module/component P0666-00 PCM / ECM / TCM
Internal Temperature
Sensor A Circuit - No
sub type information
Internal electronic control
unit temperature sensor
value above 105°C
This is a control module internal check DTC. If no
other DTCs are logged and no customer complaint
exists, clear this DTC and retest. Check the
security of control module fixings. Check the
module ground connection. Consider environmental
conditions before suspecting the control module. If
the problem persists, renew the control module.
Refer to the warranty policy and procedures
manual, or determine if any prior approval
programme is in operation, prior to the installation
of a new module/component P0702-64 Transmission Control
System Electrical -
Signal plausibility
failure
Implausibility of
differential motor
temperature sensor and
oil temperature sensor
readout detected
Motor or oil temperature
sensor circuit - short
circuit to ground or power
Check the rear differential oil quantity and
specification. Refer to the relevant section of the
workshop manual. Check both temperature sensor
circuits and connectors for damage/water ingress,
repair as necessary. Where available, after vehicle
has been switched off for at least an hour, use the
manufacturer approved diagnostic system to read
motor temperature and oil temperature sensor
values. Temperature difference should be less than
25°C. Clear the DTC and retest
Refer to the electrical circuit diagrams and check
motor temperature sensor and oil sump
temperature sensors and circuit for short circuit to
ground, short circuit to power P0712-00 Transmission Fluid Temperature Sensor A
Circuit Low - No sub
type information
Differential actuator
internal temperature
sensor circuit - open
circuit or short circuit to
ground
Refer to the electrical circuit diagrams and check
rear differential actuator motor temperature sensor
circuit for short circuit to ground, open circuit, high
resistance. Clear the DTC and retest. If no circuit
problems exist, renew the differential actuator.
Refer to the warranty policy and procedures
manual, or determine if any prior approval
programme is in operation, prior to the installation
of a new module/component

Page 218 of 3039

JAGUAR XFR 2010 1.G Workshop Manual Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Rear
Junction Box (RJB)
Description and Operation

Rear Junction Box (RJB)

CAUTION: Diagnosis by substit

Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Rear
Junction Box (RJB)
Description and Operation

Rear Junction Box (RJB)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:

If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty
Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new
module/component.

Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).

When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.

Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.

Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.

If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.

Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Rear Junction Box (RJB). For additional
diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.
For additional information, refer to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).

DTC Description Possible Causes Action P0460-11
Fuel Level Sensor A
Circuit - Circuit short to
ground
Fuel level sensor A
analogue input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor A analogue input circuit for short to
ground P0460-15
Fuel Level Sensor A
Circuit - Circuit short to
battery or open
Fuel level sensor A
analogue input circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor A analogue input circuit for short to
power, open circuit P0571-12
Brake Switch A Circuit -
Circuit short to battery
Footbrake switch digital
input signal circuits -
short to power
Refer to the electrical circuit diagrams and check
footbrake switch digital input signal circuits for
short to power P1230-12
Fuel Pump Low Speed
Malfunction (VLCM) -
Circuit short to battery
High Side output not
driven - Diagnosis
feedback indicates
output is short to power
Refer to the electrical circuit diagrams and check
fuel pump delivery module for short to power

Page 219 of 3039

JAGUAR XFR 2010 1.G Workshop Manual
DTC Description Possible Causes Action P1230-14
Fuel Pump Low Speed
Malfunction (VLCM) -
Circuit short to ground
or open
High Side output not
driven - Diagnosis
feedback indicates
output is

DTC Description Possible Causes Action P1230-14
Fuel Pump Low Speed
Malfunction (VLCM) -
Circuit short to ground
or open
High Side output not
driven - Diagnosis
feedback indicates
output is short to
ground, open circuit
Refer to the electrical circuit diagrams and check
fuel pump delivery module for short to ground, open
circuit P1230-93
Fuel Pump Low Speed
Malfunction (VLCM) - No
operation
High Side output not
driven - Diagnosis
feedback indicates
output is at open load
or short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel pump delivery module for short to power, open
circuit P1346-11
Fuel Level Sensor B
Circuit - Circuit short to
ground
Fuel level sensor B
analogue input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor B analogue input circuit for short to
ground P1346-15
Fuel Level Sensor B
Circuit - Circuit short to
battery or open
Fuel level sensor B
analogue input circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor B analogue input circuit for short to
power, open circuit P1624-13
Anti-theft System -
Circuit open
Anti-theft signal circuit
from CJB - open circuit
Refer to the electrical circuit diagrams and check
anti-theft signal circuit from CJB for open circuit C111A-11
Right Stop Lamp -
Circuit short to ground
Right stomp lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for short to ground C111A-12
Right Stop Lamp -
Circuit short to battery
Right stomp lamp
control circuit - short to
power
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for short to power C111A-13
Right Stop Lamp -
Circuit open
Right stomp lamp
control circuit - open
circuit
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for open circuit C111B-11
Left Stop Lamp - Circuit
short to ground
Left stomp lamp control
circuit - short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check left
stomp lamp control circuit for short to ground C111B-13
Left Stop Lamp - Circuit
open
Left stomp lamp control
circuit - open circuit
Refer to the electrical circuit diagrams and check left
stomp lamp control circuit for open circuit C1120-11
Reversing lamp - Circuit
short to ground
Reverse lamp control
circuit - short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short to ground C1120-12
Reversing lamp - Circuit
short to battery
Reverse lamp control
circuit - short to power
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short to power C1120-13
Reversing lamp - Circuit
open
Reverse lamp control
circuit - open circuit
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for open circuit C1120-15
Reversing lamp - Circuit
short to battery or open
Reverse lamp control
circuit - short circuit to
power, open circuit, high
resistance
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short circuit to power,
open circuit, high resistance. Repair wiring harness
as required. Clear DTC and retest

Page 220 of 3039

JAGUAR XFR 2010 1.G Workshop Manual
DTC Description Possible Causes Action B100A-51 Fuel Pump Authorisation
- Not programmed
RJB fault
Low speed CAN fault
Instrument cluster fault
Check power and ground supplies to RJB. Check C

DTC Description Possible Causes Action B100A-51 Fuel Pump Authorisation
- Not programmed
RJB fault
Low speed CAN fault
Instrument cluster fault
Check power and ground supplies to RJB. Check CAN
communications between RJB and instrument
cluster. Check power and ground supplies to
instrument cluster B100A-62 Fuel Pump Authorisation
- Signal compare failure
Low speed CAN fault
RJB fault
Instrument cluster fault
Incorrect module
installed
(RJB/Instrument cluster)
Write target SID
synchronisation error
following
re-programming
Noise/EMC related error
Check CAN communications between RJB and
instrument cluster. Check power and ground supplies
to RJB and instrument cluster. Confirm correct
module installed. Re-synchronise ID by
re-configuring the RJB as a new module. Check CAN
network for interference/EMC related issues B100A-63 Fuel Pump Authorisation
- Circuit/component
protection time-out
RJB fault
Low speed CAN fault
Instrument cluster fault
Low battery voltage <9V
Check power and ground supplies to RJB and
instrument cluster. Check CAN communications
between RJB and instrument cluster. Check battery
is in fully charged and serviceable condition, refer to
the battery care manual B1026-12
Steering Column Lock -
Circuit short to battery
Steering column lock
ground circuit - short to
power
Refer to the electrical circuit diagrams and check
steering column lock ground circuit for short to
power B1087-83
LIN Bus "A" - Value of
signal protection
calculation incorrect
The checksum of the
received LIN frame is
incorrect
Check the battery monitoring system and rear
parking aid system for DTCs and refer to relevant
DTC Index B1087-86
LIN Bus "A" - Signal
invalid
The header of the LIN
message received is
incorrect
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Check the battery monitoring system and rear
parking aid system for DTCs and refer to relevant
DTC Index B1087-88 LIN Bus "A" - Bus off
Battery monitoring
system LIN circuit -
short to ground, power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
battery monitoring system LIN circuit for short to
ground, power B108A-23
Start Button - Signal
stuck low
Start/Stop switch digital
input signal circuit -
stuck low
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
Start/Stop switch digital input signal circuit for short
to ground B10A1-11 Trailer Tow Detection -
Circuit short to ground
Trailer tow detection
digital input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
trailer tow detection digital input circuit for short to
ground B10AF-12
Blower Fan Relay -
Circuit short to battery
High Side output not
driven - Diagnosis
feedback indicates
output is short to power
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to power B10AF-14
Blower Fan Relay -
Circuit short to ground
or open
High Side output not
driven - Diagnosis
feedback indicates
output is short to
ground, open circuit
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to ground, open
circuit

Page 221 of 3039

JAGUAR XFR 2010 1.G Workshop Manual
DTC Description Possible Causes Action B10AF-93
Blower Fan Relay - No
operation
High Side output not
driven - Diagnosis
feedback indicates
output is at open load
or short to power
Carry ou

DTC Description Possible Causes Action B10AF-93
Blower Fan Relay - No
operation
High Side output not
driven - Diagnosis
feedback indicates
output is at open load
or short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to power, open
circuit B10DD-11
Airbag Deployed -
Circuit short to ground
Airbag deployed digital
input signal circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
airbag deployed digital input signal circuit for short
to ground B10DD-15
Airbag Deployed -
Circuit short to battery
or open
Airbag deployed digital
input signal circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
airbag deployed digital input signal circuit for short
to power, open circuit B10DD-38
Airbag Deployed - Signal
frequency incorrect
Signal frequency
incorrect
Check the RCM for related DTCs and refer to the
relevant DTC Index B10DE-11
Low Fuel Warning
Switch - Circuit short to
ground
Diesel run-dry switch
analogue input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
diesel run-dry switch analogue input circuit for short
to ground B10DE-15
Low Fuel Warning
Switch - Circuit short to
battery or open
Diesel run-dry switch
analogue input circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
diesel run-dry switch analogue input circuit for short
to power, open circuit B1112-11
Park Aid Ignition -
Circuit short to ground
Parking aid ignition
supply circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
parking aid ignition supply circuit for short to ground B1112-12
Park Aid Ignition -
Circuit short to battery
Parking aid ignition
supply circuit - short to
power
Refer to the electrical circuit diagrams and check
parking aid ignition supply circuit for short to power B1115-11
High Mounted Stop
Lamp Control - Circuit
short to ground
High mounted stop lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
high mounted stop lamp control circuit for short to
ground B1116-11
Left Tail Lamp - Circuit
short to ground
Left hand tail lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check left
hand tail lamp control circuit for short to ground B1117-11
Right Tail Lamp - Circuit
short to ground
Right hand tail lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right hand tail lamp control circuit for short to
ground B111A-11
Number Plate Lamps -
Circuit short to ground
Right hand or left hand
number plate lamp
control circuits - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for short to ground www.JagDocs.com

Page 222 of 3039

JAGUAR XFR 2010 1.G Workshop Manual
DTC Description Possible Causes Action B111A-12
Number Plate Lamps -
Circuit short to battery
Right hand or left hand
number plate lamp
control circuits - short to
power
Refer to the electr

DTC Description Possible Causes Action B111A-12
Number Plate Lamps -
Circuit short to battery
Right hand or left hand
number plate lamp
control circuits - short to
power
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for short to power B111A-13
Number Plate Lamps -
Circuit open
Right hand or left hand
number plate lamp
control circuits - open
circuit
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for open circuit B111A-15
Number Plate Lamps -
Circuit short to battery
or open
Right or left side licence
plate lamp(s)
inoperative
Right or left side licence
plate lamp control
circuits - short circuit to
power, open circuit, high
resistance
Refer to the electrical circuit diagrams and check
right side and left side licence plate lamp control
circuits for short circuit to power, open circuit, high
resistance. Repair wiring harness as required. Clear
DTC and retest B111D-12
Boot/Trunk Motor Open -
Circuit short to battery
Luggage compartment
lid latch actuator control
circuit - short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lid latch actuator control
circuit for short to power B111D-14
Boot/Trunk Motor Open -
Circuit short to ground
or open
Luggage compartment
lid latch actuator control
circuit - short to ground,
open circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lid latch actuator control
circuit for short to ground, open circuit B111E-11
Boot/Trunk Lamps -
Circuit short to ground
Luggage compartment
lamp control circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
to ground B111E-12
Boot/Trunk Lamps -
Circuit short to battery
Luggage compartment
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
to power B111E-13
Boot/Trunk Lamps -
Circuit open
Luggage compartment
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for open
circuit B111E-15
Boot/Trunk Lamps -
Circuit short to battery
or open
Luggage compartment
lamp inoperative
Luggage compartment
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
circuit to power, open circuit, high resistance. Repair
wiring harness as required. Clear DTC and retest B1123-12
Restraints Ignition
Relay - Circuit short to
battery
High Side output not
driven - diagnosis
feedback indicates
output is short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for short to power B1123-14
Restraints Ignition
Relay - Circuit short to
ground or open
High Side output not
driven - diagnosis
feedback indicates
output is short to
ground, open circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for short to ground,
open circuit B1123-93
Restraints Ignition
Relay - No operation
High Side output not
driven - diagnosis
feedback indicates
output is at open load
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for open load or

Page 223 of 3039

JAGUAR XFR 2010 1.G Workshop Manual
DTC Description Possible Causes Action or short to power short to power B1124-11
Lamp Fade Control -
Circuit short to ground
Interior lamp fade
control circuit - short to
ground
Refer to t

DTC Description Possible Causes Action or short to power short to power B1124-11
Lamp Fade Control -
Circuit short to ground
Interior lamp fade
control circuit - short to
ground
Refer to the electrical circuit diagrams and check
interior lamp fade control circuit for short to ground B1124-12
Lamp Fade Control -
Circuit short to battery
Interior lamp fade
control circuit - short to
power
Refer to the electrical circuit diagrams and check
interior lamp fade control circuit for short to power B113C-12
Hazard Switch
Illumination - Circuit
short to battery
Hazard switch
illumination control
circuit - short to power
Refer to the electrical circuit diagrams and check
hazard switch illumination control circuit for short to
power B113C-14
Hazard Switch
Illumination - Circuit
short to ground or open
Hazard switch
illumination control
circuit - short to ground,
open circuit
Refer to the electrical circuit diagrams and check
hazard switch illumination control circuit for short to
ground, open circuit B113E-12
External Boot/Trunk
Release Switch - Circuit
short to battery
External luggage
compartment lid release
switch digital input
circuit - short to power
Refer to the electrical circuit diagrams and check
external luggage compartment lid release switch
digital input circuit for short to power B113E-23
External Boot/Trunk
Release Switch - Signal
stuck low
External luggage
compartment lid release
switch digital input
circuit - signal stuck low
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
external luggage compartment lid release switch
digital input circuit for short to ground B11D9-49
Vehicle Battery -
Internal electronic
failure
Vehicle battery
damaged/worn out
Check battery is in fully charged and serviceable
condition using the Midtronics battery tester and
the battery care manual B11DB-49
Battery Monitoring
Module - Internal
electronic failure
Internal electronic
failure
Suspect the battery monitoring module. Check and
install a new module as required, refer to the new
module/component installation note at the top of
the DTC Index B11DB-87
Battery Monitoring
Module - Missing
message
Battery monitoring
module connector
dis-connected/poor
connection
Battery monitoring
module to RJB LIN
circuit - open circuit
Battery monitoring
module to battery
positive monitor circuit -
open circuit
Battery monitoring
module/RJB failure
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
If additional DTCs B108783, B108786, B108787 are
logged, suspect the RJB. Check and install a new
RJB as required, refer to the new module/component
installation note at the top of the DTC Index. If
additional DTCs B108783, B108786, B108787 are
NOT logged, check for good/clean contact at battery
monitoring module connector, refer to electrical
circuit diagrams and check battery monitoring
module to RJB LIN circuit and battery monitoring
module to battery positive monitor circuit for open
circuit. Clear DTC and repeat automated diagnostic
procedure using manufacturer approved diagnostic
system. If DTC remains suspect the battery
monitoring module, check and install a new battery
monitoring module as required, refer to the new
module/component installation note at the top of
the DTC Index B123A-11 Left Front Turn Indicator
- Circuit short to ground
Left front turn signal
lamp control circuit -
short to ground
Refer to the electrical circuit diagrams and check left
front turn signal lamp control circuit for short to
ground B123A-12 Left Front Turn Indicator
- Circuit short to battery
Left front turn signal
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check left
front turn signal lamp control circuit for short to
power

Page 224 of 3039

JAGUAR XFR 2010 1.G Workshop Manual
DTC Description Possible Causes Action B123A-13 Left Front Turn Indicator
- Circuit open
Left front turn signal
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams an

DTC Description Possible Causes Action B123A-13 Left Front Turn Indicator
- Circuit open
Left front turn signal
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check left
front turn signal lamp control circuit for open circuit B123A-15 Left Front Turn Indicator
- Circuit short to battery
or open
Left front turn signal
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check left
front turn signal lamp control circuit for short circuit
to power, open circuit, high resistance. Repair wiring
harness as required. Clear DTC and retest B123B-11
Right Front Turn
Indicator - Circuit short
to ground
Right front turn signal
lamp control circuit -
short to ground
Refer to the electrical circuit diagrams and check
right front turn signal lamp control circuit for short
to ground B123B-12
Right Front Turn
Indicator - Circuit short
to battery
Right front turn signal
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check
right front turn signal lamp control circuit for short
to power B123B-13
Right Front Turn
Indicator - Circuit open
Right front turn signal
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check
right front turn signal lamp control circuit for open
circuit B123B-15
Right Front Turn
Indicator - Circuit short
to battery or open
Right front turn signal
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check right
front turn signal lamp control circuit for short circuit
to power, open circuit, high resistance. Repair wiring
harness as required. Clear DTC and retest B1247-11 Left Rear Turn Indicator
- Circuit short to ground
Left rear turn signal
lamp control circuit -
short to ground
Refer to the electrical circuit diagrams and check left
rear turn signal lamp control circuit for short to
ground B1247-12 Left Rear Turn Indicator
- Circuit short to battery
Left rear turn signal
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check left
rear turn signal lamp control circuit for short to
power B1247-13 Left Rear Turn Indicator
- Circuit open
Left rear turn signal
lamp control circuit -
short to power, open
circuit
Refer to the electrical circuit diagrams and check left
rear turn signal lamp control circuit for open circuit B1247-15 Left Rear Turn Indicator
- Circuit short to battery
or open
Left rear turn signal
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check left
rear turn signal lamp control circuit for short circuit
to power, open circuit, high resistance. Repair wiring
harness as required. Clear DTC and retest B1248-11
Right Rear Turn
Indicator - Circuit short
to ground
Right rear turn signal
lamp control circuit -
short to ground
Refer to the electrical circuit diagrams and check
right rear turn signal lamp control circuit for short to
ground B1248-12
Right Rear Turn
Indicator - Circuit short
to battery
Right rear turn signal
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check
right rear turn signal lamp control circuit for short to
power B1248-13
Right Rear Turn
Indicator - Circuit open
Right rear turn signal
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check
right rear turn signal lamp control circuit for open
circuit B1248-15
Right Rear Turn
Indicator - Circuit short
to battery or open
Right rear turn signal
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check right
rear turn signal lamp control circuit for short circuit
to power, open circuit, high resistance. Repair wiring
harness as required. Clear DTC and retest

Load next 8 pages

Page: < prev 1-10 ... 185-192 193-200 201-208 209-216 217-224 225-232 233-240 241-248 249-256 ... 3040 next >

service interval reset fuse rear view mirror rims octane headlight bulb