Page 545 of 3039
Vehicles with supercharger
2.
All vehicles
3. NOTE: Make sure that the alignment mark on the driveshaft
is correctly aligned to the alignment mark on the
differential case.
Torque: 75 Nm
4. NOTES:
This step only applies if a new driveshaft is being
installed.
Using the 3mm hole on the differential case flange
and paint alignment mark on the driveshaft (as indicated).
Make sure that the alignment marks are correctly aligned.
Torque: 75 Nm
Page 546 of 3039
S/C 5.0L Petrol, Removal and Installation).
6. Refer to: Rear Halfshaft - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-05 Rear Drive Halfshafts, Removal and Installation).
7. Check and top-up the differential case.
Torque: 30 Nm
Page 547 of 3039
Published: 11-May-2011
Rear Drive Axle/Differential - Differential Front Bushing TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol
Removal and Installation
Special Tool(s)
204-274
Bush install and removal tool
204-275
Bush install and removal tool
204-335
Bush install and removal tool
204-601
Bush install tool
303-1121
Installer, Crankshaft Seal Removal
1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.
2. Refer to: Differential Case - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-02 Rear Drive Axle/Differential, Removal and Installation).
Page 548 of 3039
Installation
3. Special Tool(s): 204-335
1. NOTE: Make sure the new bushes are installed in the correct
orientation.
.
Special Tool(s): 204-275, 204-601, 303-1121, 204-274
2. Refer to: Differential Case - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-02 Rear Drive Axle/Differential, Removal and Installation). www.JagDocs.com
Page 549 of 3039
204-265
Remover/Installer, Drive Pinion Seal
204-266
Adapter for 204-265
204-267
Adapter for 204-265
204-269
Flange remover forcing screw
205-053
Retainer, Drive Flange
Page 550 of 3039
Removal
1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.
2. Refer to: Driveshaft - TD4 2.2L Diesel (205-01, Removal and
Installation).
Refer to: Driveshaft - V6 3.0L Petrol (205-01 Driveshaft, Removal and Installation).
Refer to: Driveshaft - V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-01 Driveshaft, Removal and Installation).
Refer to: Driveshaft - TDV6 3.0L Diesel (205-01 Driveshaft, Removal and Installation).
3. NOTE: Measure for installation.
Measure the depth of the pinion nut on the pinion shaft. 205-053-03
Adapter, Drive Pinion Flange
Page 551 of 3039
4. NOTE: Accurately scribe a line to mark the drive pinion
shaft to the drive pinion nut and pinion flange.
5. Special Tool(s): 205-053, 205-053-03 6. Special Tool(s): 204-266, 204-265, 204-269
Page 552 of 3039