Page 433 of 3383
ATC-32
AIR CONDITIONER CONTROL
Revision: November 20092006 QX56
System Description (Rear)EJS003XB
SWITCHES AND THEIR CONTROL FUNCTION
WJIA0623E
WJIA1067E
Page 434 of 3383
AIR CONDITIONER CONTROLATC-33
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
CAN Communication System DescriptionEJS003XC
Refer to LAN-26, "CAN COMMUNICATION" .
Page 435 of 3383

ATC-34
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
TROUBLE DIAGNOSISPFP:00004
CONSULT-II Function (HVAC)EJS003XD
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II BASIC OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and “CON-
SULT-II CONVERTER ” to the data link connector, and turn the
ignition switch ON.
2. Touch “START (NISSAN BASED VHCL) ”.
3. Touch “HVAC” on “SELECT SYSTEM ” screen. If “HVAC” is not
indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC)
Circuit" .
Diagnostic mode Description
SELF-DIAG RESULTS Displays front air control self-diagnosis results. DATA MONITOR Displays front air control input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read. ECU PART NUMBER Front air control part number can be read.
BBIA0369E
BCIA0029E
BCIA0030E
Page 436 of 3383

TROUBLE DIAGNOSISATC-35
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
SELF-DIAGNOSIS
Operation Procedure
1. Touch “SELF-DIAG RESULTS ” on “SELECT DIAG MODE”
screen to view all set DTC's.
Display Item List
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR ” on “SELECT DIAG MODE ” screen.
2. Touch either “MAIN SIGNALS” or “SELECTION FROM MENU ” on “DATA MONITOR” screen.
3. When “SELECTION FROM MENU ” is selected, touch items to be monitored. When “MAIN SIGNALS” is
selected, all the items will be monitored.
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
BCIA0031E
DTC Description
Reference page
B2573 Battery voltage out of range SC-4, "
BATTERY"
B2578 In-vehicle sensor circuit out of range (low)
ATC-137, "In-vehicle Sensor Circuit"B2579 In-vehicle sensor circuit out of range (high)
B257B Ambient sensor circuit short ATC-134, "
Ambient Sensor Circuit"B257C Ambient sensor circuit open
B257F Optical sensor (Driver) circuit open or short ATC-140, "
Optical Sensor Circuit"B2580 Optical sensor (Passenger) circuit open or short
B2581 Intake sensor circuit shortATC-142, "
Intake Sensor Circuit"B2582 Intake sensor circuit open
U1000 CAN bus fault LAN-26, "
CAN COMMUNICATION"
B2587 Stuck buttonATC-144, "FRONT AIR CONTROL"
BCIA0031E
MAIN SIGNALSMonitors all the items.
SELECTION FROM MENU Selects and monitors the individual item selected.
Page 437 of 3383

ATC-36
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Display Item List
*: DENT is displayed when MODE switch is between selections.
Monitor itemValue Contents
BATT VIA CAN "V" Displays battery voltage signal.
IGN VIA CAN "ON/OFF" Displays ignition switch signal.
DVR SUNLD SEN "w/m2" Displays optical sensor (driver) signal.
PAS SUNLD SEN "w/m2" Displays optical sensor (passenger) signal.
AMB TEMP SEN "° C/ °F" Displays ambient sensor 1 signal.
EVAP TEMP SEN "° C/ °F" Displays intake sensor signal.
INCAR TMP SEN "° C/ °F" Displays in-vehicle sensor signal.
RR TEMPSET FR "V" Displays air mix door (front) set point signal.
RR TEMPSET RR "V" Displays air mix door (rear) set point signal.
MODE FDBCK "V" Displays mode door motor feedback signal.
DVR MIX FDBCK "V" Displays air mix door motor (driver) feedback signal.
PAS MIX FDBCK "V" Displays air mix door motor (passenger) feedback signal.
RR FDBCK "V" Displays air mix door motor (rear) feedback signal.
DEF FDBCK "V" Displays defroster door motor feedback signal.
RECIRC "ON/OFF" Displays recirculation switch signal.
DEFROST "ON/OFF" Displays defroster switch signal.
AUTO "ON/OFF" Displays AUTO switch signal.
A/C "ON/OFF" Displays A/C switch signal.
MODE "ON/OFF" Displays MODE switch signal.
L TEMP UP "ON/OFF" Displays driver side temperature control dial (temp increase) signal.
L TEMP DOWN "ON/OFF" Displays driver side temperature control dial (temp decrease) signal.
R TEMP UP "ON/OFF" Displays rear temperature control dial [front (temp increase)] signal.
R TEMP DOWN "ON/OFF" Displays Rear temperature control dial [front (temp decrease)] signal.
RR DEFOG "ON/OFF" Displays rear defroster request signal.
FANUP "ON/OFF" Displays front blower motor (blower speed increase) signal.
FANDOWN "ON/OFF" Displays front blower motor (blower speed decrease) signal.
MODE SELECT " [ PNL ]"
" [ MIX ]"
" [ FLR ]"
" [ DEFR ]" " [ MAX ]"
" [ DENT ]" Displays mode door motor position.
Page 438 of 3383

TROUBLE DIAGNOSISATC-37
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
CONSULT-II Function (BCM)EJS003XE
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II BASIC OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and “CON-
SULT-II CONVERTER ” to the data link connector, and turn the
ignition switch ON.
2. Touch “START (NISSAN BASED VHCL) ”.
3. Touch “BCM” on “SELECT SYSTEM ” screen. If “BCM” is not
indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC)
Circuit" .
BCM diagnostic
test item Diagnostic mode
Description
Inspection by part WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time. ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read. ECU PART NUMBER BCM part number can be read.CONFIGURATION Performs BCM configuration read/write functions.
BBIA0369E
BCIA0029E
BCIA0030E
Page 439 of 3383

ATC-38
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
DATA MONITOR
Operation Procedure
1. Touch “AIR CONDITIONER” on “SELECT TEST ITEM” screen.
2. Touch “DATA MONITOR ” on “SELECT DIAG MODE ” screen.
3. Touch either “ALL SIGNALS ” or “SELECTION FROM MENU” on
“DATA MONITOR ” screen.
4. When “SELECTION FROM MENU” is selected, touch items to
be monitored. When "ALL SIGNALS ” is selected, all the items
will be monitored.
5. Touch “START”.
6. Touch “RECORD” while monitoring, then the status of the moni-
tored item can be recorded. To stop recording, touch “STOP”.
Display Item List
WJIA0468E
BCIA0031E
ALL SIGNALS Monitors all the items.
SELECTION FROM MENU Selects and monitors the individual item selected.
WJIA0469E
Monitor item name “ operation or
unit ” Contents
IGN ON SW “ON/OFF ”Displays “IGN Position (ON)/OFF, ACC Position (OFF) ” status as judged from ignition switch signal.
COMP ON SIG “ON/OFF ”Displays “COMP (ON)/COMP (OFF) ” status as judged from air conditioner switch signal.
FAN ON SIG “ON/OFF ”Displays “FAN (ON)/FAN (OFF) ” status as judged from blower motor switch signal.
Page 440 of 3383

TROUBLE DIAGNOSISATC-39
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
How to Perform Trouble Diagnosis for Quick and Accurate RepairEJS003XF
WORK FLOW
SYMPTOM TABLE
*1AT C - 5 8 , "Operational Check (Front)"
or ATC-60, "
Operational Check
(Rear)" .
SHA900E
Symptom Reference Page
A/C system does not come on. Go to Trouble Diagnosis Procedure for A/C System. AT C - 6 1
A/C system display is malfunctioning. Go to Navigation System. AV- 8 4
A/C system cannot be controlled.Go to Self-diagnosis Function. AT C - 5 6
Air outlet does not change.
Go to Trouble Diagnosis Procedure for Mode Door Motor. AT C - 6 4
Mode door motor is malfunctioning.
Discharge air temperature does not change.
Go to Trouble Diagnosis Procedure for Air Mix Door Motor. AT C - 7 0
Air mix door motor is malfunctioning.
Intake door does not change.
Go to Trouble Diagnosis Procedure for Intake Door Motor. AT C - 8 3
Intake door motor is malfunctioning.
Defroster door motor is malfunctioning. Go to Trouble Diagnosis Procedure for Defroster Door Motor. AT C - 8 7
Front blower motor operation is malfunction-
ing.Go to Trouble Diagnosis Procedure for Front Blower Motor.
AT C - 9 3
Rear blower motor operation is malfunction-
ing.Go to Trouble Diagnosis Procedure for Rear Blower Motor.
AT C - 1 0 1
Rear discharge air temperature and/or air
outlet does not change.Go to Trouble Diagnosis Procedure for Rear Air Control circuit.
AT C - 11 2
Magnet clutch does not engage.Go to Trouble Diagnosis Procedure for Magnet Clutch. AT C - 11 5
Insufficient coolingGo to Trouble Diagnosis Procedure for Insufficient Cooling. AT C - 1 2 1
Insufficient heatingGo to Trouble Diagnosis Procedure for Insufficient Heating. AT C - 1 2 8
NoiseGo to Trouble Diagnosis Procedure for Noise. AT C - 1 2 9
Self-diagnosis cannot be performed. Go to Trouble Diagnosis Procedure for Self-diagnosis. AT C - 1 3 0
Memory function does not operate.Go to Trouble Diagnosis Procedure for Memory Function. AT C - 1 3 1