Page 393 of 3383
AT-318
ASSEMBLY
Revision: November 20092006 QX56
b. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to AT- 2 5 0 , "
Components" .
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
c. Install new O-ring to A/T assembly harness connector. CAUTION:
Do not reuse O-ring.
Apply ATF to O-ring.
d. Connect TCM connector and park/neutral position (PNP) switch connector.
e. Install A/T assembly harness connector to control valve with TCM.
f. Connect TCM connectors.
SCIA5301E
SCIA5155E
SCIA5449E
SCIA5450E
SCIA5447E
Page 394 of 3383

ASSEMBLYAT-319
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
g. Install control valve with TCM in transmission case.
CAUTION:
Make sure that turbine revolution sensor securely installs
into turbine revolution sensor hole.
Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
Assemble it so that manual valve cutout is engaged with
manual plate projection.
h. Install bolts A, B and C to control valve with TCM.
i. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. Then tighten them in order (1 → 2 → 3), and then tighten other bolts.
j. Tighten control valve with TCM bolts to the specified torque. Refer to AT- 2 5 0 , "
Components" .
10. Connect A/T fluid temperature sensor 2 connector.
SCIA5034E
SCIA5035E
Bolt symbol Length: mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA5025E
SCIA5037E
SCIA5023E
Page 395 of 3383
AT-320
ASSEMBLY
Revision: November 20092006 QX56
11. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
12. Connect revolution sensor connector.
13. Securely fasten revolution sensor harness with terminal clips.
14. Pull down A/T assembly harness connector. CAUTION:
Be careful not to damage connector.
15. Install snap ring to A/T assembly harness connector.
SCIA5446E
SCIA5024E
SCIA7023E
SCIA5299E
SCIA5300E
Page 396 of 3383

ASSEMBLYAT-321
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
16. Install the oil pan magnets as shown.
17. Install the oil pan and new oil pan gasket.
CAUTION:
Do not reuse the oil pan gasket.
Completely remove all moisture, oil and old gasket from
the oil pan gasket mating surfaces and holes.
Always replace the oil pan bolts as they are self-sealing.
Be sure the oil pan drain plug hole is located to the rear
of the transmission assembly.
Partially install the oil pan bolts in a criss-cross pattern to
prevent dislocation of the gasket.
Be careful not to pinch harnesses.
18. Tighten new oil pan bolts in numerical order as shown.
19. Install drain plug in oil pan with new gasket. CAUTION:
Do not reuse the drain plug gasket.
20. Install torque converter.
a. Pour ATF into torque converter.
Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of fluid is
required for a new torque converter.
When reusing old torque converter, add the same amount
of fluid as was drained.
SCIA5200E
SCIA2308E
Oil pan bolts : 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA4113E
Drain plug : 34 N·m (3.5 kg-m, 25 ft-lb)
SAT428DA
Page 397 of 3383
AT-322
ASSEMBLY
Revision: November 20092006 QX56
b. Install torque converter while aligning notches of torque con-
verter with notches of oil pump.
CAUTION:
Install torque converter while rotating it.
c. Measure distance “A” to check that torque converter is in proper position.
SCIA5010E
Distance “A” : 24.0 mm (0.94 in) or more
SAT017B
Page 398 of 3383

SERVICE DATA AND SPECIFICATIONS (SDS)AT-323
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsECS00EQB
*1: Refer to MA-11, "Fluids and Lubricants" .
Vehicle Speed When Shifting GearsECS00EQC
NORMAL MODE
At half throttle, the accelerator opening is 4/8 of the full opening.
TOW MODE
At half throttle, the accelerator opening is 4/8 of the full opening.
Applied model
2WD4WD
Automatic transmission model RE5R05A
Transmission model code number 95X1C95X1D
Stall torque ratio 2.0: 1
Transmission gear ratio 1st
3.827
2nd 2.368
3rd 1.520
4th 1.000
5th 0.834
Reverse 2.613
Recommended fluid NISSAN Matic Fluid J*1
Fluid capacity 10.6 liter (11-1/4 US qt, 9-3/8 Imp qt)
CAUTION:
Use only Genuine NISSAN ATF Matic Fluid J. Do not mix with other fluid.
Using automatic transmission fluid other than Genuine NISSAN ATF Matic Fluid J will deteriorate in driveability and auto-
matic transmission durability, and may damage the automatic transmission, which is not covered by the warranty.
Final
gear
ratio Throttle position Vehicle speed km/h (MPH)
D
1 → D2D2 → D3D3 → D4D4 → D5D5 → D4D4 → D3D3 → D2D2 → D1
2.937 Full throttle
70 - 74
(44 - 46) 112 - 120
(70 - 75) 176 - 186
(110 - 116) 249 - 259
(155 - 161) 245 - 255
(152 - 159) 166 - 176
(103 - 110) 100 - 108
(62 - 67) 43 - 47
(27 - 30)
Half throttle 46 - 50
(28 - 31) 74 - 82
(46 - 51) 103 - 113
(64 - 70) 135 - 145
(84 - 90) 109 - 119
(68 - 74) 69 - 79
(43 - 49) 44 - 52
(27 - 32) 11 - 1 5
(7 - 10)
3.357 Full throttle
61 - 65
(38 - 41) 97 - 105
(61 - 66) 153 - 163
(95 - 102) 236 - 246
(147 - 153) 232 - 242
(144 - 151) 143 - 153
(89 - 95) 87 - 95
(54 - 59) 43 - 47
(27 - 29)
Half throttle 41 - 45
(26 - 28) 66 - 74
(41 - 46) 89 - 99
(56 - 62) 117 - 127
(73 - 79) 95 - 105
(59 - 65) 59 - 69
(37 - 43) 38 - 46
(24 - 29) 11 - 1 5
(7 - 10)
Final
gear
ratio Throttle position Vehicle speed km/h (MPH)
D
1 → D2D2 → D3D3 → D4D4 → D5D5 → D4D4 → D3D3 → D2D2 → D1
2.937 Full throttle
70 - 74
(44 - 46) 112 - 120
(70 - 75) 176 - 186
(110 - 116) 249 - 259
(155 - 161) 245 - 255
(152 - 159) 166 - 176
(103 - 110) 100 - 108
(62 - 67) 43 - 47
(27 - 30)
Half throttle 50 - 54
(31 - 34) 81 - 89
(50 - 55) 113 - 123
(70 - 76) 135 - 145
(84 - 90) 109 - 119
(68 - 74) 68 - 78
(42 - 48) 44 - 52
(27 - 32) 11 - 1 5
(7 - 10)
3.357 Full throttle
61 - 65
(38 - 41) 97 - 105
(61 - 66) 153 - 163
(95 - 102) 236 - 246
(147 - 153) 232 - 242
(144 - 151) 143 - 153
(89 - 95) 87 - 95
(54 - 59) 43 - 47
(27 - 29)
Half throttle 43 - 47
(27 - 29) 72 - 80
(45 - 50) 98 - 108
(61 - 67) 117 - 127
(73 - 79) 95 - 105
(59 - 65) 59 - 69
(37 - 43) 37 - 45
(23 - 28) 11 - 1 5
(7 - 10)
Page 399 of 3383

AT-324
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: November 20092006 QX56
Vehicle Speed When Performing and Releasing Complete Lock-upECS00EQD
At closed throttle, the accelerator opening is less than 1/8 condition.
At half throttle, the accelerator opening is 4/8 of the full opening.
Vehicle Speed When Performing and Releasing Slip Lock-upECS00EQE
At closed throttle, the accelerator opening is less than 1/8 condition.
Stall SpeedECS00EQF
Line PressureECS00EQG
A/T Fluid Temperature SensorECS00EQH
Turbine Revolution SensorECS00EQI
Vehicle Speed Sensor A/T (Revolution Sensor)ECS00EQJ
Final
gear
ratio Throttle position
Vehicle speed km/h (MPH)
Lock-up “ON ” Lock-up “OFF ”
2.937 Closed throttle
74 - 82 (46 - 51) 71 - 79 (45 - 49)
Half throttle 188 - 196 (117 - 122) 136 - 144 (85 - 90)
3.357 Closed throttle
65 - 73 (41 - 46) 62 - 70 (39 - 44)
Half throttle 168 - 176 (105 - 110) 118 - 126 (74 - 79)
Final
gear
ratioThrottle position Gear position Vehicle speed km/h (MPH)
Slip lock-up “ON ” Slip lock-up “OFF ”
2.937 Closed throttle 4th
52 - 60 (33 - 38) 49 - 57 (31 - 36)
5th 52 - 60 (33 - 38) 49 - 57 (31 - 36)
3.357 Closed throttle 4th
46 - 54 (29 - 34) 43 - 51 (27 - 32)
5th 46 - 54 (29 - 34) 43 - 51 (27 - 32)
Stall speed 2,500 - 2,800 rpm
Engine speedLine pressure [kPa (kg/cm
2 , psi)]
R position D position
At idle speed 425 - 465 (4.3 - 4.7, 62 - 67) 379 - 428 (3.9 - 4.4, 55 - 62)
At stall speed 1,605 - 1,950 (16.4 - 19.9, 233 - 283) 1,310 - 1,500 (13.4 - 15.3, 190 - 218)
Name Condition CONSULT-II “DATA MONITOR ” (Approx.) (V) Resistance (Approx.) (kΩ )
ATF TEMP SE 1 0
°C (32 °F) 3.3 15
20 °C (68 °F) 2.7 6.5
80 °C (176 °F) 0.9 0.9
ATF TEMP SE 2 0
°C (32 °F) 3.3 10
20 °C (68 °F) 2.5 4
80 °C (176 °F) 0.7 0.5
Name ConditionData (Approx.)
Turbine revolution
sensor 1 When running at 50 km/h (31 MPH) in 4th speed with the closed throttle position switch
“
OFF ”.
1.3 (kHz)
Turbine revolution
sensor 2 When moving at 20 km/h (12 MPH) in 1st speed with the closed throttle position switch
“
OFF ”.
Name ConditionData (Approx.)
Revolution sensor When moving at 20 km/h (12 MPH). 185 (Hz)
Page 400 of 3383
SERVICE DATA AND SPECIFICATIONS (SDS)AT-325
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
Reverse brakeECS00EQK
*: Always check with the Parts Department for the latest parts information.
To ta l E n d P l a yECS00EQL
BEARING RACE FOR ADJUSTING TOTAL END PLAY
*: Always check with the Parts Department for the latest parts information.Thickness of retaining plates
Thickness mm (in) Part number*
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205) 31667 90X14
31667 90X15
31667 90X16
31667 90X17
31667 90X18
31667 90X19
Total end play mm (in)
0.25 - 0.55 (0.0098 - 0.0217)
Thickness mm (in)Part number*
0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.4 (0.055)
1.6 (0.063)
1.8 (0.071) 31435 95X00
31435 95X01
31435 95X02
31435 95X03
31435 95X04
31435 95X05