2006 INFINITI QX56 Factory Service Manual

set clock oil open hood CD changer water pump fold seats

Page 1089 of 3383

INFINITI QX56 2006 Factory Service Manual BRC-62
[VDC/TCS/ABS]
ON-VEHICLE SERVICE
Revision: November 20092006 QX56
ON-VEHICLE SERVICEPFP:00000
Adjustment of Steering Angle Sensor Neutral PositionEFS004YH
After removing/installing or replacing

BRC-62
[VDC/TCS/ABS]
ON-VEHICLE SERVICE
Revision: November 20092006 QX56
ON-VEHICLE SERVICEPFP:00000
Adjustment of Steering Angle Sensor Neutral PositionEFS004YH
After removing/installing or replacing ABS actuator and electric unit (control unit), steering angle sensor, steer-
ing and suspension components which affect wheel alignment or after adjusting wheel alignment, be sure to
adjust neutral position of steering angle sensor before running vehicle.
NOTE:
Adjustment of steering angle sensor neutral position requires CONSULT-II.
1. Stop vehicle with front wheels in straight-ahead position.
2. Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector on vehicle, and turn ignition switch ON (do not
start engine).
3. Touch “ABS”, “WORK SUPPORT ” and “ST ANGLE SENSOR
ADJUSTMENT ” on CONSULT-II screen in this order.
4. Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle
sensor.
5. After approximately 10 seconds, touch “END”. (After approxi-
mately 60 seconds, it ends automatically.)
6. Turn ignition switch OFF, then turn it ON again.
7. Run vehicle with front wheels in straight-ahead position, then stop.
8. Select “DATA MONITOR ”, “SELECTION FROM MENU ”, and
“STR ANGLE SIG ” on CONSULT-II screen. Then check that
“STR ANGLE SIG ” is within 0±3.5 deg. If value is more than specification, repeat steps 1 to 5.
9. Erase memory of ABS actuator and electric unit (control unit) and ECM.
10. Turn ignition switch to OFF.
Calibration of Decel G SensorEFS004YI
After removing/installing or replacing ABS actuator and electric unit (control unit), yaw rate/side/decel G sen-
sor, steering and suspension components which affect wheel alignment or after adjusting wheel alignment, be
sure to calibrate the decel G sensor before running vehicle.
NOTE:
Calibration of decel G sensor requires CONSULT-II.
1. Stop vehicle with front wheels in straight-ahead position. CAUTION:
The work should be done on a level area with an unloaded vehicle.
Keep all the tires inflated to the correct pressures. Adjust the tire pressure to the specified pres-
sure value.
2. Connect CONSULT-II with CONSULT-II CONVERTER to data link connector on vehicle, and turn ignition switch ON (do not start engine).
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
3. Touch "ABS", "WORK SUPPORT" and "DECEL G SEN CALIBRATION" on CONSULT-II screen in this order. Refer to BRC-28, "
CONSULT-II BASIC OPERATION PROCEDURE" .
BBIA0369E
WFIA0239E

Page 1090 of 3383

INFINITI QX56 2006 Factory Service Manual ON-VEHICLE SERVICEBRC-63
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
4. Touch "START".
CAUTION:
Set vehicle as shown in the display.
5. After approximately 10 seconds, t

Page 1091 of 3383

INFINITI QX56 2006 Factory Service Manual BRC-64
[VDC/TCS/ABS]
WHEEL SENSORS
Revision: November 20092006 QX56
WHEEL SENSORSPFP:47910
Removal and InstallationEFS0068D
REMOVAL
1. Remove wheel sensor bolt.
When removing the front wheel sensor,

Page 1092 of 3383

INFINITI QX56 2006 Factory Service Manual SENSOR ROTORBRC-65
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
SENSOR ROTORPFP:47970
Removal and Installation EFS0068E
NOTE:
The wheel sensor rotors are built into the w

Page 1093 of 3383

INFINITI QX56 2006 Factory Service Manual BRC-66
[VDC/TCS/ABS]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
Revision: November 20092006 QX56
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)PFP:47660
Removal and InstallationEFS0068F
REMOVAL
1. Disconnect the ne

Page 1094 of 3383

INFINITI QX56 2006 Factory Service Manual ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)BRC-67
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
To install, u

Page 1095 of 3383

INFINITI QX56 2006 Factory Service Manual BRC-68
[VDC/TCS/ABS]
STEERING ANGLE SENSOR
Revision: November 20092006 QX56
STEERING ANGLE SENSORPFP:25554
Removal and InstallationEFS0068G
The steering angle sensor is an integral part of the spiral

Page 1096 of 3383

INFINITI QX56 2006 Factory Service Manual G SENSORBRC-69
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
G SENSORPFP:47930
Removal and InstallationEFS0068H
REMOVAL
1. Remove center console. Refer to IP-16, "REMOVAL

Load next 8 pages

Page: < prev 1-10 ... 1057-1064 1065-1072 1073-1080 1081-1088 1089-1096 1097-1104 1105-1112 1113-1120 1121-1128 ... 3384 next >

air filter key battery high beam carplay warning lights remote start