Page 3681 of 4323
H24319
H24318Hog Ring
H24321Hog Ring
H24861
H24317
BO±120
± BODYFRONT SEAT (Power Adjuster Type)
3673 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Turn up the seatback cover and install the hog rings.
11. INSTALL SEATBACK COVER AND PAD
(a) Install the seatback cover and pad to the seat frame as-
sembly.
(b) Install the hog rings to the seat frame assembly.
(c) Install the hog rings to the seat frame assembly.
(d) w/ Side airbag:
Connect the seatback cover bracket to the seat frame as-
sembly with the nut.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
(e) Close the fastener.
(f) Install the hog rings to the seat frame assembly.
Page 3682 of 4323

H24316
H24315
H24314
H24313
± BODYFRONT SEAT (Power Adjuster Type)
BO±121
3674 Author: Date:
2005 SEQUOIA (RM1146U)
12. INSTALL ARMREST ASSEMBLY
(a) Install the spacer to the armrest assembly.
(b) Install the armrest assembly, armrest lock plate and arm-
rest spacer with the bolt.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
HINT:
Install the armrest lock plate as shown in the illustration.
(c) Install the armrest cap.
13. INSTALL POWER SWITCH
Install the power switch with the 3 screws.
14. INSTALL LUMBAR SWITCH
Install the lumbar switch with the 2 screws to the seat cushion
outer shield.
15. INSTALL FRONT SEAT INNER BELT
(a) Install the front seat inner belt with the nut.
Torque: 42 N´m (430 kgf´cm, 32 ft´lbf)
(b) Connect the connectors and wire harness clamps.
16. INSTALL SEAT CUSHION LOWER SHIELD, SEAT
CUSHION OUTER SHIELD AND SEAT CUSHION IN-
NER SHIELD
(a) Assemble the seat cushion lower shield and seat cushion
outer shield with the screw.
(b) Perform the same procedure on the other side.
(c) Connect the lumbar switch connector to the seat cushion
outer shield, and install the seat cushion lower shield, out-
er shield and inner shield.
(d) Install the 2 screws to the seat cushion lower shield.
(e) Install the screw to the seat cushion inner shield.
(f) Install the 2 screws to the seat cushion outer shield.
Page 3683 of 4323
H24312
BO±122
± BODYFRONT SEAT (Power Adjuster Type)
3675 Author: Date:
2005 SEQUOIA (RM1146U)
(g) Install the screw to the seat cushion outer shield.
(h) Perform the same procedure on the seat cushion inner
shield.
17. INSTALL SLIDE KNOB AND RECLINING KNOB
18. INSTALL HEADREST
Page 3684 of 4323

BO4S9±01
± BODYFRONT SEAT (Power Adjuster Type)
BO±123
3676 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
The procedures listed below are for the LH side.
1. INSTALL FRONT SEAT
(a) Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the vehicle body.
(b) w/ Side airbag:
Connect the airbag connector.
(c) Connect the connectors.
(d) Slide the front seat to the rearmost position.
(e) Tighten the bolts on the front side temporarily, starting from the bolt on the inner side.
(f) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
(g) Slide the front seat to the foremost position.
(h) Tighten the bolts on the rear side temporarily, starting from the bolt on the inner side.
(i) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
2. INSTALL SEAT TRACK COVERS
3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4. Passenger 's seat:
PERFORM PASSENGER OCCUPANT CLASSIFICATION SYSTEM ZERO POINT CALIBRATION
(See page DI±1128)
5. PERFORM INITIALIZATION (See page IN±20)
Some systems need initialization when disconnecting the cable from the negative battery terminal.
Page 3685 of 4323

BO4SB±01
H24345
RH Lower Reclining
Adjuster Inside Cover
Seat Cushion
Outer Shield
Vertical Adjuster Handle Cap Reclining Adjuster Release Handle Seat Cushion
Inner ShieldRH Upper Reclining
Adjuster Inside Cover
RH Seat Cushion
Lower Shield
LH Lower Reclining
Adjuster Inside CoverLH Upper Reclining
Adjuster Inside CoverLH Seat Cushion
Lower Shield
Vertical Adjuster Handle
Non±reusable part: Specified torque
N´m (kgf´cm, ft´lbf)
Driver's seat:
Driver's seat:
37 (380, 27)
37 (380, 27)37 (380, 27)
37 (380, 27)
42 (430, 32) Seatback Cover
Seat Cushion
Cover
Seat Cushion
PadArmrest CapArmrest SpacerArmrest
Lock Plate
Spacer
Armrest AssemblyHeadrest
Headrest Support Seatback Pad
Seat Frame Assembly
Seat Position Sensor
Protector
Seat Position Sensor
Front Seat
Inner Belt Hog RingSeat Track Cover
Seat Track Cover
Hog Ring
37 (380, 27)
Occupant Classification ECUPassenger's seat:
w/ Side airbag:
5.5 (56, 49 in.´lbf)
BO±124
± BODYFRONT SEAT (Manual Adjuster Type)
3677 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT SEAT (Manual Adjuster Type)
COMPONENTS
HINT:
The procedures listed below are for the LH side.
Page 3686 of 4323

BO4SC±01
± BODYFRONT SEAT (Manual Adjuster Type)
BO±125
3678 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
CAUTION:
Work must not be started until at least 90 seconds after the ignition switch is turned to the LOCK posi-
tion and the negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source. If work is started within 90 seconds from discon-
necting the negative (±) terminal cable of the battery, the SRS may deploy.)
NOTICE:
When removing/installing and overhauling the passenger seat, check the passenger occupant clas-
sification system and perform the zero point calibration (see page DI±1128).
HINT:
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.
2. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the seat track covers.
HINT:
Tape the screwdriver tip before use.
3. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) w/ Side airbag:
Disconnect the airbag connector.
(d) Remove the front seat.
NOTICE:
Be careful not to damage the vehicle body.
Page 3687 of 4323

BO4SD±01
H24331ClawsClip
H24332
H24333
H24334ClawsClip BO±126
± BODYFRONT SEAT (Manual Adjuster Type)
3679 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:
The procedures listed below are for the LH side.
Tape the screwdriver tip before using it to remove the
parts.
1. REMOVE HEADREST
2. REMOVE SEAT CUSHION OUTER SHIELD
(a) Remove the screw from the seat cushion outer shield.
(b) Using a screwdriver, remove the seat cushion outer
shield.
HINT:
Tape the screwdriver tip before use.
3. REMOVE RECLINING ADJUSTER RELEASE HANDLE
4. REMOVE VERTICAL ADJUSTER HANDLE
(a) Using a screwdriver, remove the vertical adjuster handle
cap.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 screws and the vertical adjuster handle.
5. REMOVE SEAT CUSHION INNER SHIELD
(a) Remove the screw from the seat cushion inner shield.
(b) Using a screwdriver, remove the seat cushion inner
shield.
HINT:
Tape the screwdriver tip before use.
6. REMOVE FRONT SEAT INNER BELT
(a) Disconnect the wire harness clamps and connectors.
(b) Remove the nut and front seat inner belt.
Page 3688 of 4323
H24316
H24337
H24861
H24338Hog Ring
H24339Hog Ring
± BODYFRONT SEAT (Manual Adjuster Type)
BO±127
3680 Author: Date:
2005 SEQUOIA (RM1146U)
7. REMOVE ARMREST ASSEMBLY
(a) Using a screwdriver, remove the armrest cap.
(b) Remove the bolt, armrest spacer, armrest lock plate and
armrest assembly.
(c) Remove the spacer from the armrest assembly.
8. REMOVE SEATBACK COVER AND PAD
(a) Remove the hog rings from the seat frame assembly.
(b) Open the fastener.
(c) w/ Side airbag:
Remove the nut and disconnect the seatback cover
bracket from the seat frame assembly.
(d) Remove the hog rings shown in the illustration from the
seat frame assembly.
(e) Remove the hog rings shown in the illustration from the
seat frame assembly.
(f) Remove the seatback cover and pad from the seat frame
assembly.