Page 1865 of 4323
DI273±05
± DIAGNOSTICSSLIDING ROOF SYSTEM
DI±1663
1857 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMER PROBLEM ANALYSIS CHECK
SLIDING ROOF CONTROL SYSTEM Check Sheet
Inspector 's name:
Customer 's Name
Date of VehicleVIN
Production Date
Licence Plate No.
Odometer Reading / /km
mile
Weather Conditions
When Problem
Occurred Frequency Problem OccursWeather
Outdoor temperature
/ /
Constant Sometimes ( Times per day, month)
Once only Brought in
Sliding roof control system does not operate.
Date Problem First Occurred
Fine Cloudy Rainy Snowy
Various/Others
Hot Warm Cool
Cold (Approx. 5F ( 5C))
Problem
Symptom
Sliding roof operates abnormally or stops half way.
Jam protection system does not operate.
Page 1866 of 4323
DI276±09
DI±1664
± DIAGNOSTICSSLIDING ROOF SYSTEM
1858 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
SymptomSuspect AreaSee page
Sliding roof control system does not operate.
1. SUN ROOF Fuse
2. ECU±IG Fuse
3. Power Source Circuit
4. Sliding Roof Control Switch CircuitBE±14
BE±14
DI±1668
DI±1671
Sliding roof operates abnormally or stops half way.Sliding Roof Pulse Plate CircuitDI±1675
Jam protection system does not operate.Sliding Roof Pulse Plate CircuitDI±1675
Page 1867 of 4323
DI275±12
I04611
S19
± DIAGNOSTICSSLIDING ROOF SYSTEM
DI±1665
1859 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECU
Symbols (Terminals No.)Wiring ColorConditionSpecified Condition
MPX1 e ± (S19 ± 2 e ±)G±O e ±Multiplex communication circuit±
DWN e E
(S19 ± 3 e S19 ± 7)R±W e W±BIgnition switch ON " Sliding roof control switch TILT DOWN10 to 14 V "
Below 1 V
UP e E
(S19 ± 4 e S19 ± 7)R±Y e W±BIgnition switch ON " Sliding roof control switch TILT UP10 to 14 V "
Below 1 V
B e E
(S19 ± 5 e S19 ± 7)L±W e W±BAlways10 to 14 V
E e Body ground
(S19 ± 7 e Body ground)W±B e Body
groundAlwaysBelow 1 V
IG e E
(S19 ± 8 e S19 ± 7)B±R e W±BIgnition switch ON " Ignition switch OFF or ACC10 to 14 V "
Below 1 V
OPN e E
(S19 ± 9 e S19 ± 7)P±B e W±BIgnition switch ON " Sliding roof control switch OPEN10 to 14 V "
Below 1 V
CLS e E
(S19 ± 10 e S19 ± 7)G±Y e W±BIgnition switch ON " Sliding roof control switch CLOSE10 to 14 V "
Below 1 V
Page 1868 of 4323

DID4Z±01
DI±1666
± DIAGNOSTICSSLIDING ROOF SYSTEM
1860 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
According to the DATA LIST displayed by the hand±held tester, you can read the value of the switch, sensor,
actuator and so on without parts removal. Reading the DATA LIST as a first step of troubleshooting is one
of the method to shorten the labor time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on tester, read the ºDATA LISTº.
SLIDE ROOF:
ItemMeasurement Item/
Display (Range)Normal conditionDiagnostic Note
LIMIT SW 1Position SW NO.1/
ON or OFFON: 250 mm point from fully opened position
OFF: Sliding roof fully closed position±
LIMIT SW 2Position SW NO.2/
ON or OFFON: Sliding roof fully closed position
OFF: Sliding roof except fully closed position±
OPEN SWSliding roof open SW
signal/ON or OFFON: Sliding roof is open
OFF: Sliding roof is close±
CLOSE SWSliding roof close SW
signal/ON or OFFON: Sliding roof is close
OFF: Sliding roof is open±
UP SWSliding roof up SW sig-
nal/ON or OFFON: Sliding roof is up
OFF: Sliding roof is down±
DOWN SWSliding roof down SW
signal/ON or OFFON: Sliding roof is down
OFF: Sliding roof is up±
IG (DIRCT)Ignition SW (Direct
signal)/ON or OFFON: Ignition switch to on
OFF: Ignition switch to off±
IG (MPX)Ignition SW (MPX)/ON
or OFFON: Ignition switch to on
OFF: Ignition switch to off±
2. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one of the meth-
od to shorten the labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on tester, perform the ºACTIVE TESTº.
SLIDE ROOF:
ItemTest DetailsDiagnostic Note
SLIDE ROOFSliding roof CLOS/UP ± OPN/DWNDuring this ACTIVE TEST, jam protection caught
detection can be monitored.
Page 1869 of 4323
DI274±08
I28411
Ignition Switch Instrument Panel J/B
ECU±IG Fuse
SUN ROOF Fuse
Sliding Roof Gear Assembly
Sliding Roof ECU
Sliding Roof Motor
Sliding Roof Control Switch
± DIAGNOSTICSSLIDING ROOF SYSTEM
DI±1667
1861 Author: Date:
2005 SEQUOIA (RM1146U)
PARTS LOCATION
Page 1870 of 4323
DI277±14
I18700
J8
J/CB±R
2
L±WIG Instrument Panel J/B I18
Ignition SW
1IG1
AM1 B±Y4
1C
6
1CAM1
1 2ECU±IG
SUN ROOF1
1M
5
1M
1
1L8
5
B
W±L
B58 ALT F10
Fusible Link Block
W
Instrument Panel J/B
W±BW±B 7
1M 10
1F
IE Battery7
AS19
Sliding Roof
Control ECU
E DI±1668
± DIAGNOSTICSSLIDING ROOF SYSTEM
1862 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
Power Source Circuit
CIRCUIT DESCRIPTION
This circuit provides power to operate the sliding roof control ECU.
WIRING DIAGRAM
Page 1871 of 4323
± DIAGNOSTICSSLIDING ROOF SYSTEM
DI±1669
1863 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
If not using the hand±held tester, start from STEP 2.
1 Perform active test.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn ignition switch ON and hand±held tester main switch ON.
(c) Select the ACTIVE TEST mode on the hand±held tester.
CHECK:
Check that ºSliding roof motorº operates as the hand±held tester directs.
SLIDE ROOF:
ItemTest DetailsDiagnostic Note
SLIDE ROOFSliding roof CLOS/UP ± OPN/DWNDuring this ACTIVE TEST, jam protection caught
detection can be monitored.
NOTICE:
Caution is necessary for a part of body not to be caught in as the jam protection system does not
operate during conducting ACTIVE TEST.
HINT:
With one ACTIVE direction, the sliding roof can be slid and tilted continuously.
OK:
The slide roof operates normally.
OK Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1664).
NG
Page 1872 of 4323
DI±1670
± DIAGNOSTICSSLIDING ROOF SYSTEM
1864 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check voltage between terminals B, IG and GND of sliding roof control ECU con-
nector.
PREPARATION:
Turn ignition switch ON.
CHECK:
Measure voltage between terminals IG and GND.
OK:
Voltage: 10 to 14 V
PREPARATION:
(a) Turn ignition switch OFF.
(b) Disconnect the sliding roof control ECU connector.
CHECK:
Measure voltage between terminals B and GND.
OK:
Voltage: 10 to 14 V
OK Proceed to next circuit inspection shown on
problem symptom table (See page DI±1664).
NG
Repair or replace wire harness and connec-
tor.