Page 2985 of 4323

TR09T±04
F19317
2WD/4HI Switch
F19318
Differential Lock Switch
± TRANSFERONE TOUCH 2±4 SELECTOR SYSTEM
TR±39
2977 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
NOTICE:
4HI e 4LO: Stop the vehicle and apply the brake, then
first shift the transmission shift lever into the ºNº
position.
Do not operate the four wheel drive control switch
and the differential lock switch at the same time.
Do not change from 2WD to 4WD when vehicle speed
is 62 mph (100 km/h) or more.
1. INSPECT 2WD e 4HI (4WD and differential lock
ºFREEº) SHIFT
(a) Start the engine.
(b) Push the 2WD/4HI switch once.
(c) Check that the 4WD indicator light stays lit after blinking.
(The center differential lock indicator light blinks while be-
ing shifted.)
(d) Push the 2WD/4HI switch once again.
(e) Check that the 4WD indicator light goes off after blinking.
(The center differential lock indicator light blinks while be-
ing shifted.)
2. INSPECT 4HI (4WD and differential lock ºFREEº) e
4HI (4WD and differential lock ºLOCKº) SHIFT
(a) Start the engine.
(b) Push the 2WD/4HI switch once.
(c) Check that the 4WD indicator light stays lit after blinking.
(d) Push the differential lock switch once.
(e) Check that the center differential lock indicator light stays
lit after blinking.
(f) Push the differential lock switch once again.
(g) Check that the center differential lock indicator light goes
off after blinking.
3. INSPECT 4HI (4WD and differential lock ºLOCKº) e
2WD
(a) Start the engine.
(b) Push the 2WD/4HI once.
(c) Check that the 4WD indicator light stays lit after blinking.
(d) Push the differential lock switch once.
(e) Check that the center differential lock indicator light stays
lit after blinking.
Page 2986 of 4323

F19319
2WD/4HI Switch
F19320
4LO Switch
F19321
Differential Lock Switch
TR±40
± TRANSFERONE TOUCH 2±4 SELECTOR SYSTEM
2978 Author: Date:
2005 SEQUOIA (RM1146U)
(f) Push the 2WD/4HI switch once again.
(g) Check that the 4WD and center differential lock indicator
lights go off after blinking.
4. INSPECT 2WD e 4LO (4WD and differential lock
ºFREEº)
(a) Start the engine.
(b) Push the 4LO switch once.
(c) Check that the 4LO indicator light stays lit after blinking.
(The 4WD and center differential lock indicator lights blink
while shifting.)
(d) Push the 2WD/4HI switch once.
Check that the 4LO indicator light goes off after blinking.
(The 4WD and center differential lock indicator lights blink
while shifting.)
5. INSPECT 4LO (4WD and differential lock ºFREEº) e
4LO (4WD and differential lock ºLOCKº)
(a) Start the engine.
(b) Push the 4LO switch once.
(c) Check that the 4LO indicator light stays lit after blinking.
(d) Push the differential lock switch once.
(e) Check that the center differential lock indicator light stays
lit after blinking.
(f) Push the differential lock switch once again.
(g) Check that the center differential lock indicator light goes
off after blinking.
Page 2987 of 4323

F19322
4LO Switch
F19323
4LO Switch
± TRANSFERONE TOUCH 2±4 SELECTOR SYSTEM
TR±41
2979 Author: Date:
2005 SEQUOIA (RM1146U)
6. INSPECT 4HI (4WD and differential lock ºFREEº) e
4LO (4WD and differential lock ºFREEº)
(a) Start the engine.
(b) Push the 2WD/4HI switch once.
(c) Check that the 4WD indicator light stays lit after blinking.
(d) Push the 4LO switch once.
(e) Check that the 4WD indicator light goes off and the 4LO
indicator light stays lit after blinking.
(f) Push the 4LO switch once again.
(g) Check that the 4LO indicator light goes off after blinking
and the 4WD indicator light comes on.
7. INSPECT 4HI (4WD and differential lock ºLOCKº) e
4LO (4WD and differential lock ºLOCKº)
(a) Start the engine.
(b) Push the 2WD/4HI switch once.
(c) Check that the 4WD indicator light stays lit after blinking.
(d) Push the differential lock switch once.
(e) Check that the center differential lock indicator light stays
lit after blinking.
(f) Push the 4LO switch once.
(g) Check that the 4WD indicator light goes off and the 4LO
indicator light stays lit after blinking.
(h) Push the 4LO switch once again.
(i) Check that the 4LO indicator light goes off after blinking
and the 4WD indicator light comes on.
Page 2988 of 4323

F19324
2WD/4HI Switch
F19325
A GND
4LO
CPU 4WD
B TR±42
± TRANSFERONE TOUCH 2±4 SELECTOR SYSTEM
2980 Author: Date:
2005 SEQUOIA (RM1146U)
8. INSPECT 4LO (4WD and differential lock ºLOCKº) "
2WD
(a) Start the engine.
(b) Push the 4LO switch once.
(c) Check that the 4LO indicator light stays lit after blinking.
(d) Push the differential lock switch once.
(e) Check that the center differential lock indicator light stays
lit after blinking.
(f) Push the 2WD/4HI switch once.
(g) Check that the 4LO and center differential lock indicator
lights go off after the 4LO and 4WD indicators are blink-
ing.
9. INSPECT 2WD/4HI, 4LO AND DIFFERENTIAL LOCK
SWITCH CONTINUITY
(a) Remove the instrument panel finish lower panel.
(b) Inspect the continuity between each terminal.
Switch positionTester connectionSpecified condition
Diff. Lock OFFB±8 ± A±10No continuity
Diff. Lock Hold ONB±8 ± A±10Continuity
4LO OFFB±9 ± A±10No continuity
4LO Hold ONB±9 ± A±10Continuity
2WD/4HI OFFB±10 ± A±10No continuity
2WD/4HI Hold ONB±10 ± A±10Continuity
If continuity is not as specified, replace the instrument panel fin-
ish lower panel.
Page 2989 of 4323

F19340
A
B Four Wheel Drive Control ECU:
Transfer Actuator:
± TRANSFERONE TOUCH 2±4 SELECTOR SYSTEM
TR±43
2981 Author: Date:
2005 SEQUOIA (RM1146U)
10. INSPECT ACTUATOR
NOTICE:
Inspect the actuator with the transfer removed from the vehicle.
(a) Turn the ignition switch to ON.
(b) Check the operating sound produced by four wheel drive control switch operation and the differential
lock switch operation.
If the operating sound cannot be heard, check the four wheel control ECU and the wire harness in the next
step. When the wire harness and four wheel drive control ECU are normal, replace the actuator.
11. INSPECT WIRE HARNESS
(a) Disconnect the actuator connector and four wheel drive
control ECU connector.
(b) Check continuity of the wire harness between the four
wheel drive control ECU and the actuator.
Tester connectionSpecified condition
TM1 (A±2) ± TM1 (B±2)Continuity
TM2 (A±1) ± TM2 (B±1)Continuity
TL1 (A±41) ± TL1 (B±3)Continuity
TL2 (A±40) ± TL2 (B±4)Continuity
TL3 (A±39) ± TL3 (B±5)Continuity
HM2 (A±4) ± HM2 (B±7)Continuity
HM1 (A±3) ± HM1 (B±8)Continuity
P1 (A±10) ± CDL (B±9)Continuity
HL2 (A±42) ± HL2 (B±11)Continuity
HL1 (A±23) ± HL1 (B±12)Continuity
GND (A±7) ± GND (B±6)Continuity
GND (A±7) ± GND (B±10)Continuity
If continuity is not as specified, repair or replace the wire har-
ness.
Page 2990 of 4323

F19566
TR±44
± TRANSFERONE TOUCH 2±4 SELECTOR SYSTEM
2982 Author: Date:
2005 SEQUOIA (RM1146U)
12. INSPECT FOUR WHEEL DRIVE CONTROL ECU
(a) Connect the wire harness side connector to the four wheel drive control ECU and inspect the wire har-
ness side connector from the back, as shown.
STANDARD VALUE OF ECU TERMINAL
Terminals (Symbols)ConditionSTD Voltage (V)
3 (HM1) ± 4 (HM2)
Ignition switch ON
Four wheel drive control switch ºH4º position " Four wheel drive control switch
ºL4º position
10 to 14 " 2 or less
or
4 (HM2) ± 3 (HM1)
Ignition switch ON
Four wheel drive control switch ºL4º position " Four wheel drive control switch
ºH4º position
or
0 (0.5 s) to 14 (50 ms)
pulse generation
2 (TM1) ± 1 (TM2)
Ignition switch ON
Differential lock switch is in ºOFFº position
Four wheel drive control switch ºH2º position " Four wheel drive control switch
ºH4º position
10 to 14 " 2 or less
or
1 (TM2) ± 2 (TM1)
Ignition switch ON
Keep pressing the differential lock switch for approx. 2 seconds to turn it ON
Four wheel drive control switch ºH4ºor ºL4º position " Four wheel drive control
switch ºH2º position
or
0 (0.5 s) to 14 (50 ms)
pulse generation
5 (DM1) ± 6 (DM2)Ignition switch ON
A.D.D. FREE "A.D.D. LOCK10 to 14 " 2 or less
or
6 (DM2) ± 5 (DM2)Ignition switch ON
A.D.D. LOCK "A.D.D. FREE
or
0 (0.5 s) to 14 (50 ms)
pulse generation
4 (HM2) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH4º position " Four wheel drive control switch
ºL4º position
2 or less " 10 to 14
7 (GND) ± Body groundIgnition switch OFFContinuity
12 (IG) ± 7 (GND)Ignition switch ON10 to 14
18 (DL2) ± 7 (GND)Ignition switch ON
A.D.D. LOCK "A.D.D. FREE0.88 or less " 10 to 14
19 (DL1) ± 7 (GND)Ignition switch ON
A.D.D. FREE "A.D.D. LOCK0.88 or less " 10 to 14
23 (HL1) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH4º position " Four wheel drive control switch
ºL4º position
10 to 14 " 1.5 or less
25 (2±4) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºL4º position " Four wheel drive control switch
ºH2º or ºH4º position
10 to 14 " 1.5 or less
26 (SPD) ± 7 (GND)During drivingPulse generation
Page 2991 of 4323

± TRANSFERONE TOUCH 2±4 SELECTOR SYSTEM
TR±45
2983 Author: Date:
2005 SEQUOIA (RM1146U)28 (IND3) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH2º position " Four wheel drive control switch
ºL4º position
10 to 14 " 0 to 3.5
32 (LO) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH2º position " Four wheel drive control switch
ºL4º position
10 to 14 " 1.5 or less
33 (DL) ± 7 (GND)
Ignition switch ON
Differential lock switch is in ºOFFº position " Keep pressing the differential lock
switch for approx. 2 seconds to turn it ON
10 to 14 " 1.5 or less
9 (ADD) ± 7 (GND)Ignition switch ON
A.D.D. FREE "A.D.D. LOCK10 to 14 " 1.5 or less
39 (TL3) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH2º position " Four wheel drive control switch
ºL4º position
Differential lock switch is in ºOFFº position " Keep pressing the differential lock
switch for approx. 2 seconds to turn it ON
1.5 or less " 10 to 14
40 (TL2) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH2º position " Four wheel drive control switch
ºH4º position
Differential lock switch is in ºOFFº position " Keep pressing the differential lock
switch for approx. 2 seconds to turn it ON
10 to 14 " 1.5 or less
41 (TL1) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH2º position " Four wheel drive control switch
ºH4º or ºL4º position
Differential lock switch is in ºOFFº position " ºONº position
1.5 or less " 10 to 14
42 (HL2) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH4º position " Four wheel drive control switch
ºL4º position
1.5 or less " 10 to 14
45 (IND1) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH2º position " Four wheel drive control switch
ºH4º or ºL4º position
10 to 14 " 0 to 3.5
46 (IND2) ± 7 (GND)
Ignition switch ON
Differential lock switch is in ºOFFº position " Keep pressing the differential lock
switch for approx. 2 seconds to turn it ON
10 to 14 " 0 to 3.5
48 (N) ± 7 (GND)Ignition switch ON
Transmission shift lever: positions other than N" N1.5 or less " 10 to 14
50 (L4) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH4º position " Four wheel drive control switch
ºL4º position
10 to 14 " 2 or less
10 (P1) ± 7 (GND)
Ignition switch ON
Four wheel drive control switch ºH2º position " Four wheel drive control switch
ºH4º or ºL4º position
Differential lock switch is in ºOFFº position " ºONº position
10 to 14 " 1.5 or less
Page 2992 of 4323
PR01F±04
± PROPELLER SHAFTTROUBLESHOOTING
PR±1
2984 Author: Date:
2005 SEQUOIA (RM1146U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
2WD:
SymptomSuspected AreaSee page
Noise3. Sleeve yoke spline (Worn)
4. Spider bearing (Worn or stuck)±
PR±4
Vibration
1. Transmission extension housing rear bushing (Runout)
2. Sleeve yoke spline (Stuck)
3. Propeller shaft (Runout)
4. Propeller shaft (Imbalance)±
±
PR±4
PR±4
4WD:
SymptomSuspected AreaSee page
Noise1. Sleeve yoke spline (Worn)
2. Spider bearing (Worn or stuck)±
PR±8
Vibration
1. Transmission extension housing rear bushing (Runout)
2. Sleeve yoke spline (Stuck)
3. Propeller shaft (Runout)
4. Propeller shaft (Imbalance)±
±
PR±8
PR±8