Page 1361 of 4323

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1159
1353 Author: Date:
2005 SEQUOIA (RM1146U)Normal
(DI±1480)
Source voltage dropBattery
Airbag sensor assemblyON
NormalSystem normalOFF
*1: w/ Side and curtain shield airbag
2. DTCS FOR OCCUPANT CLASSIFICATION SYSTEM
If a trouble code is displayed during the DTC check, check the circuit listed for the code in the table below
(Proceed to the page listed for that circuit).
HINT:
When the DTC B1650/32 is detected as a result of troubleshooting for the Supplemental Restraint Sys-
tem, perform troubleshooting for the occupant classification system as shown in the chart below.
Use the hand±held tester to check/clear the DTC of the occupant classification ECU, otherwise the
DTC cannot be check/clear.
DTC No.
(See Page)Detection ItemTrouble AreaPassenger Airbag
ON/OFF Indicator
B1771
(DI±1251)Passenger side buckle switch circuit
malfunctionFront seat inner belt RH
Occupant classification ECU
Seat wire No. 1
ON
B1780
(DI±1260)
Occupant classification sensor front
LH circuit malfunctionFront seat assembly RH (Occupant classification sensor
front LH)
Occupant classification ECU
Seat wire No. 1
ON
B1781
(DI±1270)
Occupant classification sensor front
RH circuit malfunctionFront seat assembly RH (Occupant classification sensor
front RH)
Occupant classification ECU
Seat wire No. 1
ON
B1782
(DI±1280)
Occupant classification sensor rear
LH circuit malfunctionFront seat assembly RH (Occupant classification sensor
rear LH)
Occupant classification ECU
Seat wire No. 1
ON
B1783
(DI±1290)
Occupant classification sensor rear
RH circuit malfunctionFront seat assembly RH (Occupant classification sensor
rear RH)
Occupant classification ECU
Seat wire No. 1
ON
B1785
(DI±1300)Occupant classification sensor front
LH collision detectionFront seat assembly RH (Occupant classification sensor
front LH)
Occupant classification ECU
ON
B1786
(DI±1305)Occupant classification sensor front
RH collision detectionFront seat assembly RH (Occupant classification sensor
front RH)
Occupant classification ECU
ON
B1787
(DI±1310)Occupant classification sensor rear
LH collision detectionFront seat assembly RH (Occupant classification sensor
rear LH)
Occupant classification ECU
ON
B1788
(DI±1315)Occupant classification sensor rear
RH collision detectionFront seat assembly RH (Occupant classification sensor
rear RH)
Occupant classification ECU
ON
B1790
(DI±1320)
Airbag sensor assembly communica-
tion circuit malfunctionOccupant classification ECU
Airbag sensor assembly
Floor wire
Seat wire No. 1
ON
B1793
(DI±1332)Occupant classification sensor power
supply circuit malfunctionOccupant classification ECU
Front seat assembly RH (Occupant classification sensors)
Seat wire No. 1
ON
Page 1362 of 4323
DI±1160
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1354 Author: Date:
2005 SEQUOIA (RM1146U)B1794
(DI±1342)
Occupant classification ECU battery
positive line openBattery
ECU±B Fuse
Floor wire
Seat wire No. 1
Occupant classification ECU
ON
B1795
(DI±1348)Occupant classification ECU circuit
malfunctionOccupant classification ECU
Seat wire No. 1
Front seat inner belt RH
ON
B1796
(DI±1350)Sleep operation failure of occupant
classification ECUOccupant classification ECUON
Page 1363 of 4323

DIDGR±01
H10600H23564
DTC B1000/31
DLC3
TC CG
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1161
1355 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
DTC B1000/31 Airbag Sensor Assembly Malfunction
CIRCUIT DESCRIPTION
The airbag sensor assembly consists of the airbag sensor, the safing sensor, the drive circuit, the diagnostic
circuit, ignition control, etc.
If the airbag sensor assembly receives signals from the airbag sensor, it determines whether or not the SRS
should be activated.
DTC B1000/31 is recorded when a malfunction is detected in the airbag sensor assembly.
DTC No.DTC Detection ConditionTrouble Area
B1000/31Airbag sensor assembly malfunctionAirbag sensor assembly
HINT:
When a trouble code is displayed simultaneously with B1000/31, repair the malfunction indicated by this
code (except B1000/31) first.
INSPECTION PROCEDURE
1 Check airbag sensor assembly.
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1000/31 is not output.
NG Replace airbag sensor assembly
(see page RS±84).
OK
Using simulation method, reproduce malfunction symptoms (see page IN±24).
Page 1364 of 4323

H02750
Airbag Sensor Assembly
A20+SR 29
IL31
IL32
A2027 A12
Front Airbag Sensor RH
2
1±SR W
W
BB +SR
±SR DI±1162
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1356 Author: Date:
2005 SEQUOIA (RM1146U)
DTC B1610/13 Front Airbag Sensor RH Malfunction
CIRCUIT DESCRIPTION
The front airbag sensor RH consists of the diagnosis circuit, the frontal deceleration sensor, etc.
If the airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether
or not the SRS should be activated.
DTC B1610/13 is recorded when a malfunction is detected in the front airbag sensor RH circuit.
DTC No.DTC Detection ConditionTrouble Area
B1610/13
The airbag sensor assembly receives a line short circuit
signal, an open circuit signal, a short circuit to ground sig-
nal or a short circuit to B+ signal in the front airbag sensor
RH circuit for 2 seconds.
Front airbag sensor RH malfunction
Airbag sensor assembly malfunction
Front airbag sensor RH
Airbag sensor assembly
Cowl wire
Engine room main wire
WIRING DIAGRAM
DIDGS±01
Page 1365 of 4323

H02757H10600H40103H23566
CG
TCDTC B1610/13
DLC3 Front Airbag
Sensor RHAirbag
Sensor
Assembly
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1163
1357 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
CAUTION:
Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag de-
ployment.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the airbag sensor assembly.
(d) Disconnect the connectors from the steering wheel pad.
(e) Disconnect the connectors from the front passenger airbag assembly.
(f) w/ Side and curtain shield airbag:
Disconnect the connectors from the side airbag assembly LH and RH.
(g) w/ Side and curtain shield airbag:
Disconnect the connectors from the curtain shield airbag assembly LH and RH.
(h) Disconnect the connectors from the front seat outer belt LH and RH.
1 Check DTC.
PREPARATION:
(a) Connect the connectors to the airbag sensor assembly.
(b) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1610/13 is not output.
HINT:
Codes other than DTC B1610/13 may be output at this time, but
they are not related to this check.
NG Go to step 2.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
Page 1366 of 4323

H03353H08016G27651H23623
Front Airbag
Sensor RHAirbag
Sensor
Assembly
+SR
±SR
A
B D F
E
C C
Service Wire
+SR ±SR
A20A12
DI±1164
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1358 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check connection of connectors.
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
CHECK:
Check that the connectors are properly connected to the airbag sensor assembly and the front airbag sensor
RH.
OK:
The connectors are connected securely.
NG Connect connectors, then go to step 1.
OK
3 Check front airbag sensor RH circuit (open).
PREPARATION:
(a) Disconnect the connectors from the airbag sensor as-
sembly and the front airbag sensor RH.
(b) Using a service wire, connect A12±2 (+SR) and A12±1
(±SR) of connector ºEº.
NOTICE:
Do not forcibly insert a service wire into the terminals of the
connector when connecting.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±29 (+SR) ±
A20±27 (±SR)AlwaysBelow 1 W
NG Go to step 8.
OK
Page 1367 of 4323

H03355G27651H23624
Front Airbag
Sensor RHAirbag
Sensor
Assembly
±SR +SR
A
B D E F
C
A20
H03355G27651H23624
Front Airbag
Sensor RHAirbag
Sensor
Assembly
±SR +SR
A
B D E F
C
A20
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1165
1359 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check front airbag sensor RH circuit (short).
PREPARATION:
Disconnect the service wire from connector ºEº.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±29 (+SR) ±
A20±27 (±SR)Always1 MW or higher
NG Go to step 9.
OK
5 Check front airbag sensor RH circuit (short to B+).
PREPARATION:
Connect the negative (±) terminal cable to the battery, and wait
for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±29 (+SR) ±
Body groundIgnition switch ONBelow 1 V
A20±27 (±SR) ±
Body groundIgnition switch ONBelow 1 V
NG Go to step 10.
OK
Page 1368 of 4323
H03355G27651H23624
Front Airbag
Sensor RHAirbag
Sensor
Assembly
±SR +SR
A
B D E F
C
A20
DI±1166
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1360 Author: Date:
2005 SEQUOIA (RM1146U)
6 Check front airbag sensor RH circuit (short to ground).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±29 (+SR) ±
Body groundAlways1 MW or higher
A20±27 (±SR) ±
Body groundAlways1 MW or higher
NG Go to step 11.
OK