Page 1225 of 4323
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1023
1217 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check operation of the ABS warning light.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position and hand±held tester main switch ON.
(c) Select the ACTIVE TEST mode on the hand±held.
CHECK:
Check that ºONº and ºOFFº of the ABS warning light can be shown on the combination meter with the hand±
held tester.
ItemVehicle Condition/Test DetailsDiagnostic Note
ABS WARN LIGHTTurn ABS warning light ON/OFFObserve combination meter
OK:
ABS warning light operates.
NG Go to step 4
OK
2 Is DTC output?
Check DTC on page DI±911.
YES Repair circuit indicated by the output code
(See page DI±921).
NO
3 Check that the skid control ECU connector is securely connected to the skid
control ECU (See page IN±35).
NG Connect the connector to the skid control ECU.
OK
Page 1226 of 4323
DI±1024
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1218 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check harness and connector between skid control ECU and combination meter
(See page IN±35).
NG Repair or replace harness or connector.
OK
5 Check ABS warning light.
See combination meter troubleshooting on page DI±1614.
NG Repair combination meter assembly
(See page DI±1610).
OK
Check and replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform the zero point calibration (See page DI±897).
Page 1227 of 4323

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1025
1219 Author: Date:
2005 SEQUOIA (RM1146U)
ABS Warning Light Circuit (Does not light up)
CIRCUIT DESCRIPTION
See page DI±1021.
WIRING DIAGRAM
See page DI±1021.
INSPECTION PROCEDURE
1 Check operation of the ABS warning light.
When using the hand±held tester:
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position and hand±held tester main switch ON.
(c) Select the ACTIVE TEST mode on the hand±held.
CHECK:
Check that ºONº and ºOFFº of the ABS warning light can be shown on the combination meter with the hand±
held tester.
ItemVehicle Condition/Test DetailsDiagnostic Note
ABS WARN LIGHTTurn ABS warning light ON/OFFObserve combination meter
OK:
ABS warning light operates.
When not using the hand±held tester:
PREPARATION:
(a) Turn the ignition switch OFF.
(b) Disconnect the connector from the skid control ECU.
(c) Turn the ignition switch to the ON position.
CHECK:
Check the ABS warning light comes on.
OK:
ABS warning light comes on.
NG Go to step 2.
OK
Check and replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform the zero point calibration (See page DI±897).
DIDML±01
Page 1228 of 4323
DI±1026
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1220 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check harness and connector between skid control ECU and combination meter
(See page IN±35).
NG Repair or replace harness or connector.
OK
3 Check ABS warning light.
See combination meter troubleshooting on page DI±1614.
NG Repair combination meter assembly
(See page DI±1610).
OK
Check and replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform the zero point calibration (See page DI±897).
Page 1229 of 4323
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1027
1221 Author: Date:
2005 SEQUOIA (RM1146U)
VSC TRAC Warning Light Circuit (Remains ON)
CIRCUIT DESCRIPTION
If the ECU stores a DTC to shut down VSC & TRAC operation, the VSC TRAC warning light on the combina-
tion meter come on.
DI945±03
Page 1230 of 4323
F19778
ABS & VSC Actuator
(Skid Control ECU)
VSCW 44
S1 P±L IL2 3 P±L
3 C6
Combination SW Instrument Panel J/B
11
1HB±O
24
2 1CIGN1
B±R
I18
Ignition SW
IG2 AM2
IG1
AM13
1C
6
1C
4
1C7
1J
1
1L
4
1F AM1
ECU±IG1 2
265
1W±R
W±L
B±YW±R
WBB 1
2C1
2D
B±RSub J/B No.3
8
3A8
3CB±R
B±R
B±R B±R
W±B A
J37
A
J38 A
J371
IL113
S1
IG1 IG1
GND1
40O
O A
AA
AW±B
W±B W±B
J18
J/C J43
J/C17
IL1
9
IL11
S1 GND1
GND2 32
S1
IG
IG W
B
B 5 8
4
ALTF10
Fusible
Link
Block
BatteryEngine Room J/B
AM2
J/C T5
Translate ECUVSC TRAC
7
11L
WB±R
L
W 7
IL26
S1
6
IL22
S1CANH
CANL VSC+
VSC±
(*) CAN1 Circuit (*) (*)
(*)
(*) DI±1028
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1222 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
Page 1231 of 4323

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1029
1223 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 2 when not using the
hand±held tester.
1 Check operation of the VSC warning light.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position and push the hand±held tester main switch ON.
(c) Select ACTIVE TEST mode on the hand±held tester.
CHECK:
Check that ºONº and ºOFFº of the VSC TRAC warning light can be shown on the combination meter with
the hand±held tester.
ItemVehicle Condition / Test DetailsDiagnostic Note
VSC / TRC OFF INDTurns VSC / TRAC OFF indicator ON / OFFObserve combination me-
ter
OK:
VSC TRAC warning light operates.
OK Go to step 5.
NG
2 Is DTC output?
Check DTC on page DI±911.
YES Repair circuit indicated by the output code
(See page DI±921).
NO
3 Check for open and short circuit in harness and connector between skid control
ECU and VSC TRAC warning light (See page IN±35).
NG Repair or replace harness or connector.
OK
Page 1232 of 4323
DI±1030
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1224 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check VSC TRAC warning light.
See combination meter troubleshooting on page DI±1614.
NG Repair combination meter assembly
(See page DI±1610).
OK
Replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform the zero point calibration (See page DI±897).
5 Is DTC output?
Check DTC on page DI±911.
YES Repair circuit indicated by the output code (See
page DI±921).
NO
Replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform the zero point calibration (See page DI±897).