Page 481 of 4323
A23556
8 J17
J/CECM Combination Meter
SPD
E5 G±O
B G±O 25
C5
B
± DIAGNOSTICSENGINE
DI±279
473 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
Related DTCsP0500Vehicle speed sensor ºAº pulse input error
Main sensorsVehicle speed sensor
Required sensors/componentsRelated sensorsPark/Neutral position switch, Engine coolant tem-
perature sensor, Combination meter
Frequency of operationContinuous
Duration500 times
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Vehicle speed is 9 km/h (5.59 mph) or
more4 sec.±
Park/neutral position switchOFF
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Sensor signalNo pulse input
WIRING DIAGRAM
Page 482 of 4323

DI±280
± DIAGNOSTICSENGINE
474 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check operation of speedometer.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and push the hand±held tester main switch ON.
(c) Start the engine.
(d) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / PRIMARY / VEHICLE SPD.
CHECK:
Read the mass air flow rate on the hand±held tester.
RESULT:
Vehicle speedProceed to
Vehicle speed remains 0 km/h (0 mph)A
Vehicle speed is lower than actual speedA
Vehicle speed is same as actual speedB
B Check for intermittent problems
(See page DI±11).
A
Page 483 of 4323

B17411
SPD(+) E6
E5
E1
AT7809
4 to 6 V
Turn the Wheel
3
2
1
I25536
Component Side Connector:
Vehicle Speed Sensor
± DIAGNOSTICSENGINE
DI±281
475 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check voltage between terminal SPD and E1 of ECM connector.
PREPARATION:
(a) Shift the shift lever to neutral.
(b) Jack up the rear wheel on one side.
(c) Turn the ignition switch ON.
CHECK:
Measure the voltage between the specified terminal of the E5
and E6 ECM connector when the wheel is turned slowly.
OK:
Standard:
Tester ConnectionSpecified Condition
SPD (E5±8) ± E1 (E6±1)Generated intermittently
HINT:
The output voltage should fluctuate up and down similarly to the
diagram on the left when the wheel is turned slowly.
OK Replace ECM (See page SF±80).
NG
3 Check vehicle speed sensor.
PREPARATION:
(a) Disconnect the vehicle speed sensor connector.
(b) Connect the battery positive (+) lead to terminal 1 and the
battery negative (±) lead to terminal 2.
(c) Connect the tester positive (+) lead to terminal 3 and the
tester negative (±) lead to terminal 2.
(d) Shift the shift lever to N position.
(e) Rotate the shaft.
CHECK:
Check that there is voltage change between terminals 2 and 3.
OK:
Standard: 0 V to 10 V or more
NG Replace vehicle speed sensor.
OK
Page 484 of 4323
BR3795OK NGClearance
B17411
SPD(+) E5
A23540
Wire Harness Side:
Front View
Combination Meter Connector C5
DI±282
± DIAGNOSTICSENGINE
476 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check sensor installation (Vehicle speed sensor).
CHECK:
Check the vehicle speed sensor installation.
OK:
The vehicle speed sensor is installed properly.
NG Tighten sensor installation bolt.
OK
5 Check for open and short in harness and connector between combination meter
and ECM.
PREPARATION:
(a) Disconnect the C5 combination meter connector.
(b) Disconnect the E5 ECM connector.
CHECK:
Check for resistance between the wire harness side connec-
tors.
OK:
Standard (Check for open):
Symbols (Terminal No.)Specified condition
SPD (E5±8) ± C5±25Below 1 W
Standard (Check for short):
Symbols (Terminal No.)Specified condition
SPD (E5±8) or C5±25 ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Check combination meter circuit (See page
DI±1632
Page 485 of 4323
± DIAGNOSTICSENGINE
DI±283
477 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0504 Brake Switch ºAº/ºBº Correlation
CIRCUIT DESCRIPTION
In addition to turning on the stop lamps, the stop lamp switch signals are used for a variety of engine, trans-
mission, and suspension functions as well as being an input for diagnostic checks. It is important that the
switch operates properly, therefore this switch is designed with two complementary signal outputs: STP and
ST1±. The ECM analyzes these signal outputs to detect malfunctions in the stop lamp switch.
HINT:
Normal condition is as shown in the table.
SignalBrake pedal releasedIn transitionBrake pedal depressed
STPOFFONON
ST1±ONONOFF
DTC No.DTC Detection ConditionTrouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 sec. or more:
(a) Ignition switch ON
(b) Brake pedal released
(c) STP signal is OFF when the ST1± signal is OFFShort in stop lamp switch signal circuit
Stop lamp fuse
Stop lamp switch
ECM
DID8C±01
Page 486 of 4323
I18
Ignition
SW
A23552
ECM
STOPSTP
ALT
BatteryE4
16 G±Y
J/C1 S14 Stop Light SW
2
G±W
BR7
Stop
Light
LH
R8
Stop
Light
RH3
5
8W±R
A W
High
Mounted
Stop Light
W±B 1L
1 1F
7
F10
Fusible
Link
BlockInstrument
Panel J/B1
4EG±Y
4B8
Brake Inhibit Relay
G±Y 4
See VSC System 2
W
J19
J/CB
C
IC
CC
C
4
BD1
1
22
1H9 H9(*1)
(*2) (*1)(*2)
BD2
12 J/C
A1
4
G±W IG2
*1: w/o Rear Spoiler
*2: w/ Rear Spoiler AM2
To Towing
Converter Relay
W±BST1±
E4 15
4C 4A1
1
3
L±B Sub J/B No.4
2
IGN1 B±O2
4D2
4A
1E 17
2 1C
1 A
J44J11
J/C J10
J
J33
J34 C
3
IJ
52C
2D 11
AM2
B W±RB±R
6
Instrument
Panel J/B
BP1
4 G±W B±O
G±W
G±W G±WSub J/B No.4
J10
J45
4
BJ J57
J/CA
W±BW±B G±W
High
Mounted
Stop LightG±WJ20
J/C G±W H
Engine Room
J/B DI±284
± DIAGNOSTICSENGINE
478 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
Page 487 of 4323
± DIAGNOSTICSENGINE
DI±285
479 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check operation of stop light.
CHECK:
Check if the stop lights come on and go off normally when the brake pedal is operated and released.
NG Check and repair stop light circuit.
OK
2 Check stop light switch (See page BE±47).
NG Replace stop light switch.
OK
Page 488 of 4323
B17446
Brake Pedal
DepressedBrake Pedal
Released ON
() ()
ST1±(+)E4
E6
E1(±)
DI±286
± DIAGNOSTICSENGINE
480 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check STP signal and ST1± voltage.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) Select the item ºDIAGNOSIS / ENHANCED OBD II /
DATA LIST / ALL / STOP LIGHT SWº.
CHECK:
Read the signal displayed on the hand±held tester.
OK:
Standard:
Brake PedalSpecified Condition
DepressedSTP Signal ON
ReleasedSTP Signal OFF
CHECK:
Measure the voltage between the specified terminals of the E4
and E6 ECM connectors.
OK:
Standard:
Tester ConnectionBrake PedalSpecified Condition
ST1± (E4±12) ±
E1 (E6±1)DepressedBelow 1.5 V
ST1± (E4±12) ±
E1 (E6±1)Released7.5 to 14 V
OK Check for intermittent problems (See page
DI±11).
NG