Page 3377 of 4323
RS0BP±11
H23878N´m (kgf´cm, ft´lbf): Specified torque Front Airbag Sensor (LH) Front Airbag Sensor (RH)
17.5 (179, 13)
17.5 (179, 13)
RS±86
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
3369 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT AIRBAG SENSOR
COMPONENTS
Page 3378 of 4323
RS0TI±03
H23879
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
RS±87
3370 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
NOTICE:
If the wiring connector of the SRS is disconnected
with the ignition switch in the ON position, DTCs will
be recorded.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
Never reuse a front airbag sensor if the airbag has
previously deployed in a collision.
1. PRECAUTION (SEE PAGE RS±1 and RS±3)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
3. REMOVE FRONT AIRBAG SENSOR LH
(a) Disconnect the front airbag sensor LH connector.
NOTICE:
Disconnect the connector with the sensor assembly
installed.
(b) Remove the 2 nuts and front airbag sensor LH.
Page 3379 of 4323
RS11H±01
RS±88
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
3371 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. VEHICLE NOT INVOLVED IN COLLISION
Perform a diagnostic system check (see page DI±1147).
2. VEHICLE INVOLVED IN COLLISION AND AIRBAG IS NOT DEPLOYED
Perform a diagnostic system check (see page DI±1147).
3. VEHICLE INVOLVED IN COLLISION AND AIRBAG IS DEPLOYED
Replace the front airbag sensor LH and RH (see page DI±1147).
Page 3380 of 4323
RS0BS±07
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
RS±89
3372 Author: Date:
2005 SEQUOIA (RM1146U)
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the front airbag sensor with a new one.
The SRS has been deployed in a collision. (replace both the left and right airbag sensors.)
The front airbag sensor has been found to be faulty in troubleshooting.
The front airbag sensor has been found to be faulty while checking items (see page RS±88).
The front airbag sensor has been dropped.
CAUTION:
For removal and installation of the front airbag sensor, see page RS±87 and RS±90. Be sure to follow
the correct procedure.
Page 3381 of 4323

H23879
RS11I±01
RS±90
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
3373 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the front airbag sensor involved in a col-
lision when the airbag has deployed.
If the front airbag sensor center has been dropped, or
there are any cracks, dents or other defects in the
case, bracket or connector, replace it with a new one.
When installing the front airbag sensor center, be
careful that the SRS wiring does not interfere with
other parts and that it is not pinched between other
parts.
After installing, shake the front airbag sensor to
check that there is no looseness.
1. INSTALL FRONT AIRBAG SENSORS LH
(a) Install the front airbag sensors LH with the 2 nuts.
Torque: 17.5 N´m (179 kgf´cm, 13 ft´lbf)
(b) Connect the front airbag sensor connectors.
2. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
3. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
4. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)
Page 3382 of 4323
RS11J±01
H23903: Specified torqueN´m (kgf´cm, ft´lbf)Front Door Scuff Plate Center Pillar Lower Garnish
Front Seat Outer
Belt Retractor
Side Airbag Sensor
Assembly LH
Rear Door Scuff Plate
Front Seat Outer Belt Floor Anchor
17.5 (179, 13)
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG SENSOR ASSEMBLY
RS±91
3374 Author: Date:
2005 SEQUOIA (RM1146U)
SIDE AIRBAG SENSOR ASSEMBLY
COMPONENTS
Page 3383 of 4323

RS11K±01
H20066
RS±92
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG SENSOR ASSEMBLY
3375 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
NOTICE:
If the wiring connector of the SRS is disconnected
with the ignition switch in the ON position, DTCs will
be recorded.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
Never reuse the side airbag sensor assembly if the
airbag has previously deployed in a collision.
1. PRECAUTION (SEE PAGE RS±1 and RS±3)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
3. REMOVE FRONT DOOR SCUFF PLATE
(SEE PAGE BO±89)
4. REMOVE REAR DOOR SCUFF PLATE
(SEE PAGE BO±89)
5. REMOVE FRONT SEAT OUTER BELT FLOOR AN-
CHOR (SEE PAGE BO±101)
6. REMOVE CENTER PILLAR LOWER GARNISH
(SEE PAGE BO±101)
7. REMOVE FRONT SEAT OUTER BELT RETRACTOR
(SEE PAGE BO±163)
8. REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH
(a) Disconnect the connector from the side airbag sensor as-
sembly LH.
(b) Remove the 3 bolts and the side airbag sensor assembly
LH.
Page 3384 of 4323
RS11L±01
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG SENSOR ASSEMBLY
RS±93
3376 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. VEHICLE NOT INVOLVED IN COLLISION
Perform a diagnostic system check (see page DI±1147).
2. VEHICLE INVOLVED IN COLLISION AND AIRBAG IS NOT DEPLOYED
Perform a diagnostic system check (see page DI±1147).
3. VEHICLE INVOLVED IN COLLISION AND AIRBAG IS DEPLOYED
Replace the side airbag sensor assembly (see page DI±1147).