Page 417 of 4323
A03401
IGT Signal Waveform
IGT
GND
IGF
20 msec./Division GND
A20793
Normal Ignition signal
(IGT)
Ignition
confirmation
signal (IGF)Malfunction
Circuit Open ECM
IGFIGT
IgniterIgnition Coil
Time Ignition Coil with Igniter
± DIAGNOSTICSENGINE
DI±223
417 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P0351
P0352
P0353
P0354
P0355
P0356
P0357
P0358
No IGF signal to ECM while engine is running
Open or short in IGF1 or IGF2 and IGT1 to IGT8 circuit from
ignition coil with igniter to ECM
No. 1 to No. 8 ignition coil with igniter (primary ignition)
Ignition system
ECM
Reference: Inspection using the oscilloscope.
During cranking or idling, check the waveform between termi-
nals IG1 to IG8 and E1, and IGF1, IGF2 and E1 of the E6 and
E8 ECM connectors.
MONITOR DESCRIPTION
If the ECM does not receive the IGF after sending the IGT it interprets this as a fault in the igniter and sets
a DTC.
Page 418 of 4323

DI±224
± DIAGNOSTICSENGINE
418 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
P0351No. 1 ignition coil with igniter circuit malfunction
P0352No. 2 ignition coil with igniter circuit malfunction
P0353No. 3 ignition coil with igniter circuit malfunction
RltdDTCP0354No. 4 ignition coil with igniter circuit malfunctionRelated DTCsP0355No. 5 ignition coil with igniter circuit malfunction
P0356No. 6 ignition coil with igniter circuit malfunction
P0357No. 7 ignition coil with igniter circuit malfunction
P0358No. 8 ignition coil with igniter circuit malfunction
Required sensors/componentsIgniter
Frequency of operationContinuous
Duration0.256 sec. + 4 sparks
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
Engine speed±1,500 rpm
Either of the following conditions is met:Condition 1 or 2
1. Following conditions are met:Condition (a) and (b)
(a) Engine speed±500 rpm
(b) Battery voltage6 V±
2. Following conditions are met:Condition (a) and (b)
(a) Engine speed500 rpm±
(b) Battery voltage10 V±
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
ºIgnition signal fail countºMore than 2
ºIgnition signal fail countº is on the right:When IGF does not return despite sending IGT.
COMPONENT OPERATING RANGE
Standard Value
Confirmed signal number = ignition signal number
Page 419 of 4323
A15470A19381
I8 Ignition Coil with Igniter No. 8
B±W
BR23
Ignition Coil with Igniter No. 7 I7
4
1
B±R
B±RECM
24
E8IGF1
IGF2
IGT8 E8
25
12E8
IGT7 9
E8
IGT6
11E8
15 E8 IGT5
E8
8IGT4
IGT3
E814
IGT2 13
E8
E8 10
IGT1
I18 Ignition SW
W±R IG2
AM25 1C2
1C3 IGN2 Instrument Panel J/B
2
1D
7 B±R 5
IG4 B±R
W±R
Engine Room J/B
2C 1
2DAM2 1
2
B
BatteryF10
Fusible Link Block4 1 2
N1 Noise Filter No. 1
B±R
1 3B±R4
BR
EC
2
I1 Ignition Coil with Igniter No. 1
B±R
I2 Ignition Coil with Igniter No. 2
1 3
4 2
B±W
BRB±R
I3 Ignition Coil with Igniter No. 3
BRBR
B±R B±R
B±R
B±R
B±R
B±R B±RB±R
3B±R1
4 2
B±W
I4 Ignition Coil with Igniter No. 4
413
2
I5 Ignition Coil with Igniter No. 5B±W
I6 Ignition Coil with Igniter No. 6
1 3
2
4
13
2
41 4 23
BR
B±W
G±R
P±L
G±W
R±W
G±B
LG±B
B±L
B±R
LG
BR
BR
BR
1J
BR
B±R
B±R
B±R
B±R
6
B±R BR
BR BRBRBR BR BR B±R
B±R
B±R
B
± DIAGNOSTICSENGINE
DI±225
419 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
Page 420 of 4323
DI±226
± DIAGNOSTICSENGINE
420 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
If DTCs P0351, P0354, P0356 and P0357 are output simultaneously, IGF1 circuit may be open or
short.
If DTCs P0352, P0353, P0355 and P0358 are output simultaneously, IGF2 circuit may be open or
short.
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.
1 Check spark plug and spark (See page IG±1).
NG Go to step 4.
OK
Page 421 of 4323

A21025
Wire Harness Side:
I1
I2
I3I4
I5I6
I7I8
Ignition Coil with Igniter Connector
B17412
E8
IGF2IGF1
ECM Connector
± DIAGNOSTICSENGINE
DI±227
421 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open and short in harness and connector in IGF signal circuits be-
tween ECM and ignition coil with igniter.
PREPARATION:
(a) Disconnect the I1, I2, I3, I4, I5, I6, I7 or I8 ignition coil with
igniter connector.
(b) Disconnect the E8 ECM connector.
CHECK:
Check the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
Ignition coil (I1±2) ± IGF1 (E8±24)Below 1 W
Ignition coil (I2±2) ± IGF2 (E8±25)Below 1 W
Ignition coil (I3±2) ± IGF1 (E8±24)Below 1 W
Ignition coil (I4±2) ± IGF2 (E8±25)Below 1 W
Ignition coil (I5±2) ± IGF1 (E8±24)Below 1 W
Ignition coil (I6±2) ± IGF2 (E8±25)Below 1 W
Ignition coil (I7±2) ± IGF1 (E8±24)Below 1 W
Ignition coil (I8±2) ± IGF2 (E8±25)Below 1 W
Ignition coil (I1±2) or IGF1 (E8±24) ±
Body ground10 kW or higher
Ignition coil (I2±2) or IGF2 (E8±25) ±
Body ground10 kW or higher
Ignition coil (I3±2) or IGF1 (E8±24) ±
Body ground10 kW or higher
Ignition coil (I4±2) or IGF2 (E8±25) ±
Body ground10 kW or higher
Ignition coil (I5±2) or IGF1 (E8±24) ±
Body ground10 kW or higher
Ignition coil (I6±2) or IGF2 (E8±25) ±
Body ground10 kW or higher
Ignition coil (I7±2) or IGF1 (E8±24) ±
Body ground10 kW or higher
Ignition coil (I8±2) or IGF2 (E8±25) ±
Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Page 422 of 4323
B17411
IGF1 IGF2(+) (+)E8
E6
E1 (±)
DI±228
± DIAGNOSTICSENGINE
422 Author: Date:
2005 SEQUOIA (RM1146U)
3 Disconnect ignition coil with igniter connector, and check voltage between ter-
minals IGF1, IGF2 and E1 of ECM connector.
PREPARATION:
(a) Disconnect the I1, I2, I3, I4, I5, I6, I7 or I8 ignition coil with
igniter connector.
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage between the E8 and E6 ECM connectors.
OK:
Standard:
Tester ConnectionSpecified Condition
IGF1 (E8±24) ± E1 (E6±1)4.5 to 5.5 V
IGF2 (E8±25) ± E1 (E6±1)4.5 to 5.5 V
NG Replace ECM (See page SF±80).
OK
Replace ignition coil with igniter.
Page 423 of 4323

A21025
Wire Harness Side:
I1
I2
I3I4
I5I6
I7I8
Ignition Coil with Igniter Connector
B17412
E8
IGT8 IGT2
IGT4
IGT5
IGT6IGT3 IGT7IGT1
ECM Connector
± DIAGNOSTICSENGINE
DI±229
423 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check for open and short in harness and connector in IGT signal circuit between
ECM and ignition coil with igniter.
PREPARATION:
(a) Disconnect the I1, I2, I3, I4, I5, I6, I7 or I8 ignition with ig-
niter coil connector.
(b) Disconnect the E8 ECM connector.
CHECK:
Check the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
Ignition coil (I1±2) ± IGT1 (E8±8)Below 1 W
Ignition coil (I2±2) ± IGT2 (E8±15)Below 1 W
Ignition coil (I3±2) ± IGT3 (E8±11)Below 1 W
Ignition coil (I4±2) ± IGT4 (E8±10)Below 1 W
Ignition coil (I5±2) ± IGT5 (E8±13)Below 1 W
Ignition coil (I6±2) ± IGT6 (E8±12)Below 1 W
Ignition coil (I7±2) ± IGT7 (E8±14)Below 1 W
Ignition coil (I8±2) ± IGT8 (E8±9)Below 1 W
Ignition coil (I1±2) or IGT1 (E8±8) ±
Body ground10 kW or higher
Ignition coil (I2±2) or IGT2 (E8±15) ±
Body ground10 kW or higher
Ignition coil (I3±2) or IGT3 (E8±11) ±
Body ground10 kW or higher
Ignition coil (I4±2) or IGT4 (E8±10) ±
Body ground10 kW or higher
Ignition coil (I5±2) or IGT5 (E8±13) ±
Body ground10 kW or higher
Ignition coil (I6±2) or IGT6 (E8±12) ±
Body ground10 kW or higher
Ignition coil (I7±2) or IGT7 (E8±14) ±
Body ground10 kW or higher
Ignition coil (I8±2) or IGT8 (E8±9) ±
Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Page 424 of 4323
B17411E8
IGT8
IGT2IGT4
IGT5 IGT6IGT3
IGT7IGT1E1(+)(±) (+) (+)
(+)
(+)
(+)
(+)
(+)
E6
DI±230
± DIAGNOSTICSENGINE
424 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check voltage between terminals IGT1 ± IGT8 and E1 of ECM connector.
PREPARATION:
Turn the ignition switch to ON.
CHECK:
Measure the voltage between terminals the E8 and E6 ECM
connectors when the engine is cranked.
OK:
Standard:
Tester ConnectionSpecified Condition
IGT1 (E8±8) ± E1 (E6±1)More than 0.1 V or less than 4.5 V
IGT2 (E8±15) ± E1 (E6±1)More than 0.1 V or less than 4.5 V
IGT3 (E8±11) ± E1 (E6±1)More than 0.1 V or less than 4.5 V
IGT4 (E8±10) ± E1 (E6±1)More than 0.1 V or less than 4.5 V
IGT5 (E8±13) ± E1 (E6±1)More than 0.1 V or less than 4.5 V
IGT6 (E8±12) ± E1 (E6±1)More than 0.1 V or less than 4.5 V
IGT7 (E8±14) ± E1 (E6±1)More than 0.1 V or less than 4.5 V
IGT8 (E8±9) ± E1 (E6±1)More than 0.1 V or less than 4.5 V
NG Replace ECM (See page SF±80).
OK