Page 2601 of 4323
A23302
RH No.3 Timing Belt Cover
No.2 Timing
Belt Cover
LH No.3 Timing Belt Cover Drive Belt Idler Pulley
Camshaft Position
Sensor ConnectorCover Plate
Oil Cooler Pipe Engine Wire
7.5 (76, 66 in.´lbf)
16 (160, 12)
7.5 (76, 66 in.´lbf)
N´m (kgf´cm, ft´lbf) : Specified torque
Wire Grommet
39 (400, 29)
A23303
Timing BeltLH Camshaft Timing Pulley
Timing Belt Tensioner
Dust Boot
245 (2,500, 181)
16 (160, 12)
32 (330, 24)
RH Camshaft Timing Pulley
26 (270, 19)Fan Bracket
N´m (kgf´cm, ft´lbf) : Specified torque
8.1 (83, 72 in.´lbf)
EM±14
± ENGINE MECHANICALTIMING BELT
2593 Author: Date:
2005 SEQUOIA (RM1146U)
Page 2602 of 4323
A23304
Generator WireDrive Belt Tensioner
No.1 Timing Belt Cover Generator
Crankshaft Pulley
39 (400, 29)
No.1 Idler Pulley
Timing Belt
Plate Washer
Crankshaft Timing Pulley
Timing Belt Cover Spacer No.2 Idler Pulley
Timing Belt Guide
(Crankshaft Angle Sensor Plate)Gasket
34.5 (350, 25)
34.5 (350, 25)
N´m (kgf´cm, ft´lbf) : Specified torque
Precoated part
26 (265, 19)
39 (400, 29)
15.5 (158, 11)
± ENGINE MECHANICALTIMING BELT
EM±15
2594 Author: Date:
2005 SEQUOIA (RM1146U)
Page 2603 of 4323

EM1WX±01
A08934
A04329
A04331
EM±16
± ENGINE MECHANICALTIMING BELT
2595 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. REMOVE RADIATOR ASSEMBLY (See page CO±17)
4. REMOVE THROTTLE BODY COVER
5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY
6. REMOVE DRIVE BELT, FAN, FLUID COUPLING AND
FAN PULLEY
(a) Loosen the 4 nuts holding the fluid coupling to the fan
bracket.
(b) Remove the drive belt. (See page CH±7)
(c) Remove the 4 nuts, the fan, fluid coupling assembly and
fan pulley.
7. DISCONNECT PS PUMP
Remove the 3 bolts, and disconnect the PS pump from the en-
gine.
HINT:
Suspend the PS pump securely.
8. REMOVE DRIVE BELT IDLER PULLEY
Remove the pulley bolt, cover plate and idler pulley.
9. REMOVE RH NO.3 TIMING BELT COVER
Remove the 3 bolts, nut and RH No.3 timing belt cover.
10. REMOVE LH NO.3 TIMING BELT COVER
(a) Disconnect the engine wire from the 2 wire clamps.
(b) Remove the 4 bolts and nut.
(c) Disconnect the camshaft position sensor wire from the
wire clamp on the LH No.3 timing belt cover.
(d) Disconnect the camshaft position sensor connector from
the connector bracket.
(e) Disconnect the camshaft position sensor connector.
(f) Remove the wire grommet from the LH No.3 timing belt
cover.
Page 2604 of 4323
A04330
A04455
A23305
A23306
SST
± ENGINE MECHANICALTIMING BELT
EM±17
2596 Author: Date:
2005 SEQUOIA (RM1146U)
(g) Remove the LH No.3 timing belt cover.
(h) Remove the bolt, nut and oil cooler pipe.
11. REMOVE NO.2 TIMING BELT COVER
Remove the 2 bolts and No.2 timing belt cover.
12. DISCONNECT A/C COMPRESSOR FROM ENGINE
(See page EM±79)
13. REMOVE FAN BRACKET
Remove the 2 bolts, 2 nuts and fan bracket.
14. IF RE±USING TIMING BELT, CHECK INSTALLATION
MARKS ON TIMING BELT
Check that there are 3 installation marks on the timing belt by
turning the crankshaft pulley as shown in the illustration.
HINT:
If the installation marks have disappeared, place a new installa-
tion mark on the timing belt before removing each part.
15. LOOSEN CRANKSHAFT PULLEY BOLT
Using SST, loosen the pulley bolt.
SST 09213±70011 (90105±08076), 09330±00021
Page 2605 of 4323

A23307Turn
A23308
A14391
Approx. 50°Idler
Pulley
Bolt
Timing
Mark
Crankshaft
Pulley Bolt
Turn
A23309
EM±18
± ENGINE MECHANICALTIMING BELT
2597 Author: Date:
2005 SEQUOIA (RM1146U)
16. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley and align its groove with timing
mark º0º of the No.1 timing belt cover.
(b) Check that the timing marks of the camshaft timing pul-
leys and timing belt rear plates are aligned.
If not, turn the crankshaft 1 revolution (360°).
(c) Turn the crankshaft pulley approx. 50° clockwise, and
align the timing mark of the crankshaft pulley with the cen-
ters of the crankshaft pulley bolt and the No.2 timing belt
idler pulley bolt.
NOTICE:
If the timing belt is disengaged, having the crankshaft
pulley at the wrong angle can cause the piston head and
valve head to come into contact with each other when you
remove the camshaft timing pulley (step 15), causing dam-
age. So always set the crankshaft pulley at the correct
angle.
(d) Remove the crankshaft pulley bolt.
NOTICE:
Do not turn the crankshaft pulley.
17. REMOVE TIMING BELT TENSIONER
HINT:
When re±using the timing belt:
If the installation marks have disappeared, before remove
the timing belt, place 2 new installation marks on the tim-
ing belt to match the timing marks of the camshaft timing
pulleys.
Page 2606 of 4323

A23310
String
A04339
A23311
Slightly Turn
A23312
SST
± ENGINE MECHANICALTIMING BELT
EM±19
2598 Author: Date:
2005 SEQUOIA (RM1146U)
When replacing the timing belt tensioner only:
To avoid meshing of the timing pulley and timing belt, se-
cure one of them with string. And place matchmarks on
the timing belt and RH camshaft timing pulley.
Alternately loosen the 2 bolts, and remove them, the belt ten-
sioner and dust boot.
18. DISCONNECT TIMING BELT FROM CAMSHAFT TIM-
ING PULLEYS
(a) Hold the camshaft timing pulley with SST, and loosen the
tension spring between the LH and RH camshaft timing
pulleys by slightly turning the LH camshaft timing pulley
clockwise.
SST 09960±10010 (09962±01000, 09963±01000)
HINT:
Set the SST so that the claw comes in contact with the camshaft
timing pulley bolt, and tighten the lock nut of the SST.
(b) Disconnect the timing belt from the camshaft timing pul-
leys.
19. REMOVE CAMSHAFT TIMING PULLEYS
(a) Hold the camshaft timing pulley with SST, loosen the 4
bolts of the timing pulley.
SST 09960±10010 (09962±01000, 09963±01000)
(b) Remove the 2 timing pulleys.
20. REMOVE GENERATOR (See page CH±7)
21. REMOVE DRIVE BELT TENSIONER
Remove the bolt, 2 nuts and belt tensioner.
Page 2607 of 4323

A23313
SST
A04448
A04342
A04444
A04445SST
EM±20
± ENGINE MECHANICALTIMING BELT
2599 Author: Date:
2005 SEQUOIA (RM1146U)
22. REMOVE CRANKSHAFT PULLEY
Using SST, remove the crankshaft pulley.
SST 09950±50013 (09951±05010, 09952±05010,
09953±05010, 09953±05020, 09954±05021)
NOTICE:
Do not turn the crankshaft pulley.
23. REMOVE NO.1 TIMING BELT COVER
Remove the 4 bolts and timing belt cover.
24. REMOVE TIMING BELT GUIDE
25. REMOVE TIMING BELT COVER SPACER
26. REMOVE TIMING BELT
HINT:
If re±using the belt and the installation mark has disappeared
from it, place a new installation mark on the timing belt to the
match the dot mark of the crankshaft timing pulley.
27. REMOVE NO.1 IDLER PULLEY AND NO.2 IDLER
PULLEY
(a) Using a 10 mm hexagon wrench, remove the bolt, No.1
idler pulley and plate washer.
(b) Remove the bolt and No.2 idler pulley.
28. REMOVE CRANKSHAFT TIMING PULLEY
Using SST, remove the timing pulley.
SST 09950±50013 (09951±05010, 09952±05010,
09953±05010, 09953±05020, 09954±05011)
NOTICE:
Do not turn the timing pulley.
Page 2608 of 4323

EM0KX±07
EM3336
NO !
P20079
P20633
± ENGINE MECHANICALTIMING BELT
EM±21
2600 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT TIMING BELT
NOTICE:
Do not bend, twist or turn the timing belt inside out.
Do not allow the timing belt to come into contact with
oil, water or steam.
Do not utilize timing belt tension when installing or re-
moving the mount bolt of the camshaft timing pulley.
If there is any defect, as shown in the illustration, check these
points:
(a) Premature parting
Check for proper installation.
Check the timing cover gasket for damage and
proper installation.
(b) If the belt teeth are cracked or damaged, check to see if
either camshaft is locked.
(c) If there is noticeable wear or cracks on the belt face,
check to see if there are nicks on the side of the idler
pulley lock and water pump.
(d) If there is wear or damage on even one side of the belt,
check the belt guide and the alignment of each pulley.
(e) If there is noticeable wear on the belt teeth, check timing
cover for damage and for foreign material on the pulley
teeth.
If necessary, replace the timing belt.
2. INSPECT IDLER PULLEYS
(a) Visually check the seal portion of the idler pulley for oil
leakage.
If leakage is found, replace the idler pulley.
(b) Check that the idler pulley turns smoothly.
If necessary, replace the idler pulley.
3. INSPECT TIMING BELT TENSIONER
(a) Visually check the seal portion of the tensioner for oil leak-
age.
HINT:
If there is only the faintest trace of oil on the seal on the push
rod side, the tensioner is all right.
If leakage is found, replace the tensioner.