2001 TOYOTA SEQUOIA Service Repair Manual

power steering display brakes service glove box buttons

Load previous 8 pages

Page 817 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual ± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±615
809 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit mal

Page 818 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DI±616
± DIAGNOSTICSAUTOMATIC TRANSMISSION
810 Author: Date:
2005 SEQUOIA (RM1146U) Last ECM selected gear
4th
ON malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)

Page 819 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual ECM command gearshift
Shift solenoid valve S21st 2nd 3rd 4th 5th
OFF ON
ON OFF OFF
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±617
811 Author: Date:
2005 SEQUOIA (RM1146U) ON malfunction (E)
Turbine

ECM command gearshift
Shift solenoid valve S21st 2nd 3rd 4th 5th
OFF ON
ON OFF OFF
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±617
811 Author: Date:
2005 SEQUOIA (RM1146U) ON malfunction (E)
Turbine speed ± Output speed x 5th gear ratio
(NT ± NO x 5th gear ratio)1,000 rpm or more
INSPECTION PROCEDURE
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
HINT:
While driving, the shift position can be forcibly changed with the hand±held tester.
Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you
to confirm the problem (See page DI±567).
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]
Press º"º button: Shift up
Press ºuº button: Shift down
Possible to check the operation of
the shift solenoid valves.
HINT:
This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
The 4th to 5th up±shiftings must be performed with the accelerator pedal released.
The 5th to 4th down±shiftings must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the hand±
held tester.
The shift solenoid valve S2 is turned on/off normally when the shift lever is in the D position:

Page 820 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DI±618
± DIAGNOSTICSAUTOMATIC TRANSMISSION
812 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check other DTCs output (in addition to DTC P0756).
PREPARATION:
(a) Turn the ignition switch off.
(b) Conne

Page 821 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual D11992
Shift solenoid S2:
(+) (±)
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±619
813 Author: Date:
2005 SEQUOIA (RM1146U)
2 Inspect shift solenoid valve S2 operation.
PREPARATION:
Remove the shift

Page 822 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DI±620
± DIAGNOSTICSAUTOMATIC TRANSMISSION
814 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0771 Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
SYSTEM DESCRIPTION
The ECM uses signals

DI±620
± DIAGNOSTICSAUTOMATIC TRANSMISSION
814 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0771 Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0771The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Shift solenoid valve SR remains open or closed
Shift solenoid valve SL1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve SR or SL1.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
Related DTCsP0771Shift solenoid valve SR/Rationality check
Rid /C tMainShift solenoid valve SRRequired sensors/ComponentsSubSpeed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE)
Frequency of operationContinuous
OFF malfunction (A)0.4 sec.
DurationOFF malfunction (B) and (C)ImmediateDuration
ON malfunction0.15 sec.
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
DIDJE±01

Page 823 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual ± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±621
815 Author: Date:
2005 SEQUOIA (RM1146U) ETCS (Electric throttle control system)
Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Sp

Page 824 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual ECM command gearshift
Shift solenoid valve SR1st 2nd 3rd 4th 5th
OFF
OFF OFF
Shift solenoid valve SL1OFF
OFF OFFON
ON OFF
OFF DI±622
± DIAGNOSTICSAUTOMATIC TRANSMISSION
816 Author: Date:
2005 SEQU

ECM command gearshift
Shift solenoid valve SR1st 2nd 3rd 4th 5th
OFF
OFF OFF
Shift solenoid valve SL1OFF
OFF OFFON
ON OFF
OFF DI±622
± DIAGNOSTICSAUTOMATIC TRANSMISSION
816 Author: Date:
2005 SEQUOIA (RM1146U) OFF malfunction (C)
Output record from ECM for 4th " 5th upshiftingRecorded
[ON malfunction]
2 detections are necessary per driving cycle
1st detection; temporary flag ON
2nd detection; temporary pending fault code ON
Turbine speed ± Output speed x 1st gear ratio
(NT ± NO x 1st gear ratio)150 rpm or more
INSPECTION PROCEDURE
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
HINT:
While driving, the shift position can be forcibly changed with the hand±held tester.
Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you
to confirm the problem (See page DI±567).
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]
Press º"º button: Shift up
Press ºuº button: Shift down
Possible to check the operation of
the shift solenoid valves.
HINT:
This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
The 4th to 5th up±shiftings must be performed with the accelerator pedal released.
The 5th to 4th down±shiftings must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the hand±
held tester.
The shift solenoid valve SR and SL1 is turned on/off normally when the shift lever is in the D position:

Load next 8 pages

Page: < prev 1-10 ... 785-792 793-800 801-808 809-816 817-824 825-832 833-840 841-848 849-856 ... 4328 next >

fuel filter location wiper fluid snow chains lock diagnostic menu clock setting