Page 3697 of 4323
H23455
BO4R9±02
BO±136
± BODYREAR NO.1 SEAT (Separate Type)
3689 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
HINT:
The procedures listed below are for the RH side.
1. FOLD REAR SEAT RH
(a) Lower the headrest to the lowest position.
(b) Pull the seatback angle adjusting lever and fold the seat-
back down.
(c) Unlock the seat legs by pulling up one of the levers on the
seat legs, and swing the seat up and forward.
2. REMOVE REAR SEAT RH
(a) Using a screwdriver, remove the 2 seat leg covers.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 4 bolts and rear No.1 seat.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
Page 3698 of 4323

BO4SG±01
H17260
H23459
Hook
± BODYREAR NO.1 SEAT (Separate Type)
BO±137
3690 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:
The procedures listed below are for the RH side.
A bolt without a torque specification is shown in the stan-
dard bolt chart (see page SS±2).
Tape the screwdriver tip before using it to remove the
parts.
1. REMOVE HEADREST
2. REMOVE RECLINING ADJUSTER RELEASE HANDLE
3. REMOVE NO. 1 REAR SEAT RECLINING COVER
(a) Remove the screw and No. 1 rear seat reclining cover.
(b) Perform the same procedure on the other side.
4. REMOVE SEATBACK ASSEMBLY
(a) Tilt the seat forward.
(b) As shown in the illustration, disengage the hook and open
the seatback cover.
(c) Remove the 4 bolts and the seatback assembly.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
5. REMOVE SEATBACK COVER
(a) Remove the headrest supports.
(b) Disengage the hooks, and remove the seatback frame
from the seatback cover with pad.
(c) Remove the seatback cover from the seatback pad.
HINT:
At the time of reassembly, take as much care as possible to
minimize wrinkles when installing hog rings.
Page 3699 of 4323

H17261
Hexagon
Bolt
H23461
BO±138
± BODYREAR NO.1 SEAT (Separate Type)
3691 Author: Date:
2005 SEQUOIA (RM1146U)
6. REMOVE REAR SEAT CUSHION UNDER COVER
(a) Using a 5 mm hexagon wrench, remove the bolt and
cushion.
(b) Remove the 6 screws and rear seat cushion under cover.
(c) Remove the screw and fold seat stopper band.
7. REMOVE FOLD SEAT LOCK CONTROL CABLE NO. 1
Using a screwdriver, remove the fold seat lock control cable No.
1.
HINT:
Tape the screwdriver tip before use.
8. REMOVE LH REAR SEAT RECLINING ADJUSTER
AND LH REAR SEAT LOCK
(a) Unfasten the bolt, then remove the rear No. 1 seat inner
belt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(b) Remove the 2 nuts and LH rear seat reclining adjuster.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(c) Remove the bolt and LH rear seat lock.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
9. REMOVE RECLINING CONNECTING PIPE
10. REMOVE RH REAR SEAT RECLINING ADJUSTER
Remove the 2 nuts and RH rear seat reclining adjuster.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
11. REMOVE SEAT CUSHION COVER
(a) Remove the seat cushion cover with pad from the seat
cushion frame.
(b) Remove the seat cushion cover from the seat cushion
pad.
HINT:
At the time of reassembly, take as much care as possible to
minimize wrinkles when installing hog rings.
12. REMOVE REAR SEAT CUSHION HINGE LH
(a) Using a screwdriver, remove the E±ring.
(b) Remove the pin, bushings, spring, collar and rear seat
cushion hinge.
(c) Remove the rear seat cushion hinge on the other side us-
ing the same procedures (a) and (b) described above.
13. REMOVE RH REAR SEAT LOCK
Remove the 2 bolts and RH rear seat lock.
Torque: 64 N´m (653 kgf´cm, 47 ft´lbf)
Page 3700 of 4323
BO4RB±02
± BODYREAR NO.1 SEAT (Separate Type)
BO±139
3692 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (see page BO±137).
Page 3701 of 4323
BO4RC±02
BO±140
± BODYREAR NO.1 SEAT (Separate Type)
3693 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (see page BO±136).
Page 3702 of 4323

BO4SH±01
H16778
Rear Seat Shoulder Belt Cover
Rear Seat Shoulder
Belt GuideHeadrest
Armrest
Seatback Pad
Rear Seat
Protector No. 1 Reclining Cover
Seat Cushion Cover
Seat Cushion Pad
Seat Cushion FrameSeatback Frame
Rear Seatback
Protector
Seatback Cover
Hinge
Cover
RH Rear Seat Lock
LH Rear Seat Lock
43 (430, 32)
Hinge Cover
No. 1 Fold Seat
Lock Control CableFold Seat
Stopper Band
Seat Cushion
Under Cover Rear Seat
Cushion Cover LH
Cushion Seat Leg Cover
Rear Seat Cushion Hinge Rear Seat Stay Rear Seat
Cushion HingeRear No. 1 Seat
Inner Belt
Seat Adjuster
Control Cable
Hinge
Cover
Hinge Cover
Rear Seat
Outer Belt
Rear No. 1 Seat Inner Adjuster
Seat Inner
Bracket
Rear Seat
Cushion Cover RH
37 (380, 27)
37 (380, 27)N´m (kgf´cm, ft´lbf) : Specified torque
Non±reusable part
Reclining Adjuster
Release Handle No. 1 Reclining Cover
Rear No. 1
Seat Outer
Adjuster
42 (430, 31)
43 (440, 32)
42 (430, 31)
43 (440, 32)
42 (430, 31)
42 (430, 31)
Hog Ring
Hog Ring
± BODYREAR NO.1 SEAT (Split Type LH)
BO±141
3694 Author: Date:
2005 SEQUOIA (RM1146U)
REAR NO.1 SEAT (Split Type LH)
COMPONENTS
Page 3703 of 4323
BO4SI±01
BO±142
± BODYREAR NO.1 SEAT (Split Type LH)
3695 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
REMOVE REAR NO.1 SEAT
(a) Fold the seatback down.
(b) Unlock the seat lock, and swing the whole seat up and forward.
(c) Using a screwdriver, remove the seat leg covers.
HINT:
Tape the screwdriver tip before use.
(d) Remove the 4 bolts and rear No.1 seat.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
Page 3704 of 4323
BO4SJ±01
H05304
H05321
± BODYREAR NO.1 SEAT (Split Type LH)
BO±143
3696 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:
A bolt without a torque specification is shown in the stan-
dard bolt chart (see page SS±2).
Tape the screwdriver tip before using it to remove the
parts.
1. REMOVE HEADREST
2. REMOVE RECLINING ADJUSTER RELEASE HANDLE
3. REMOVE NO. 1 RECLINING COVERS
(a) Zip the seat cushion cover open.
(b) Remove the 2 screws and 2 No. 1 reclining covers.
4. REMOVE SEAT CUSHION UNDER COVER
(a) Remove the 2 screws and 2 seat cushion under covers.
(b) Remove the 10 screws and seat cushion under cover
sub±assembly.