Page 3617 of 4323
BO±56
± BODYROOF DRIP SIDE MOULDING
3609 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Lift the moulding release sheet from the face of moulding.
NOTICE:
When the moulding release sheet is removed, make sure
that no dirt or dust can get onto the coated area.
(c) Install the moulding.
NOTICE:
Make sure that the body and moulding are heated to
a proper temperature.
Do not depress the adhesive coated parts excessive-
ly but just hold them down with your thumb.
Scrape off any overflowing adhesive with a plastic
spatula and clean the surface with a dry rag.
Take care not to drive the vehicle during the time de-
scribed in the table below.
TemperatureMinimum time prior to driving the vehicle
35 °C (95 °F)1.5 hours
20 °C (68 °F)5 hours
5°C (41° F)24 hours
6. w/ Roof rack:
INSTALL ROOF RACK (See page BO±173)
Torque: 11 N´m (115kgf´cm, 8 ft´lbf)
Page 3618 of 4323
BO46F±01
H16706
Roof Side Rail Weatherstrip
Center Pillar Upper
End Weatherstrip
± BODYROOF DRIP SIDE FINISH MOULDING
BO±57
3610 Author: Date:
2005 SEQUOIA (RM1146U)
ROOF DRIP SIDE FINISH MOULDING
COMPONENTS
Page 3619 of 4323
H16707
BO46G±01
H16708
H16709
BO±58
± BODYROOF DRIP SIDE FINISH MOULDING
3611 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE CENTER PILLAR UPPER END WEATH-
ERSTRIP
Using a screwdriver, remove the weatherstrip.
HINT:
Tape the screwdriver tip before use.
2. REMOVE ROOF SIDE RAIL WEATHERSTRIP
Using SST, pull off the roof side rail weatherstrip from end.
SST 09806±30010
HINT:
At the time of installation, please refer to the following item.
Attach the upper edge of the weatherstrip to body flange. Tap
on the weatherstrip by hand.
Page 3620 of 4323
BO46H±01
± BODYROOF DRIP SIDE FINISH MOULDING
BO±59
3612 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page BO±58).
Page 3621 of 4323
BO46I±02
H18890
Roof Console BoxFront Door Opening
Trim WeatherstripRoof Headlining
Assist Grip
Assist Grip Plug Front Pillar Garnish
Sun Visor
Roof Console BoxAssist Grip
Front Pillar
Garnish Sun Visor
Holder Holder
Inner Rear
View Mirror
No. 2 Stopper
Windshield Outside
Upper Moulding
Windshield Outside Moulding
Roof Side Rail
Weatherstrip Windshield
Outside Moulding
Windshield Glass
Wiper Arm
Wiper Arm
Cowl Top Ventilator Louver
Hood to Cowl Top Seal
Non±reusable part
N´m (kgf´cm, ft´lbf): Specified torque No. 2 Stopper
Dam w/ Sliding roof:
Roof Side Rail
Weatherstrip
w/ Electro chrmic
inner rear view mirror:
Mirror Cover
Inner Rear
View Mirror
2.5 (25, 22 in.´lbf)
Front Door
Opening Trim
Weatherstrip
w/ Double sun visor:
Sun Visor
2.5 (25, 22 in.´lbf)
Dam
Assist Grip Plug
Holder
Holder
Siding Roof
Headlining
Trim
20 (204, 15)
BO±60
± BODYWINDSHIELD
3613 Author: Date:
2005 SEQUOIA (RM1146U)
WINDSHIELD
COMPONENTS
Page 3622 of 4323

BO4HJ±01
H16717
Clip
H167342 Clips
H167354 Clips
H18891
± BODYWINDSHIELD
BO±61
3614 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE FRONT DOOR OPENING TRIM WEATH-
ERSTRIPS
2. REMOVE FRONT PILLAR GARNISH
(a) Remove the assist grip.
(1) Using a screwdriver, remove the 2 assist grip plugs.
HINT:
Tape the screwdriver tip before use.
(2) Remove the 2 screws and assist grip.
(b) Remove the front pillar garnish.
(c) Use the same manner described above to the other side.
3. REMOVE SUN VISORS AND HOLDERS
4. w/ Sliding roof:
REMOVE ROOF CONSOLE BOX
(a) Remove the 2 screws.
(b) Using a screwdriver, remove the roof console box.
HINT:
Tape the screwdriver tip before use.
(c) Disconnect the connectors.
5. w/o Sliding roof:
REMOVE ROOF CONSOLE BOX
(a) Remove the 4 screws.
(b) Using a screwdriver, remove the roof console box.
HINT:
Tape the screwdriver tip before use.
(c) Disconnect the connectors.
6. w/o Electro chromic inner rear view mirror:
REMOVE INNER REAR VIEW MIRROR
Remove the torx screw and inner rear view mirror as shown in
the illustration.
Page 3623 of 4323

H18892
H16708
H05613
BO5232
H05619
BO±62
± BODYWINDSHIELD
3615 Author: Date:
2005 SEQUOIA (RM1146U)
7. w/ Electro chromic inner rear view mirror:
REMOVE INNER REAR VIEW MIRROR
(a) Remove the mirror cover.
(b) Disconnect the connector.
(c) Remove the torx screw and inner rear view mirror.
8. REMOVE WIPER ARMS
(a) Using a screwdriver, remove the 2 caps.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 nuts and wiper arms.
9. REMOVE COWL TOP VENTILATOR LOUVER
(a) Remove the hood to cowl top seal.
(b) Using a clip remover, remove the 6 clips.
(c) Remove the 8 screws and cowl top ventilator louver.
10. REMOVE ROOF SIDE RAIL WEATHERSTRIP
Using SST, pull off the roof side rail weatherstrip from front end.
SST 09806±30010
11. REMOVE WINDSHIELD OUTSIDE MOULDINGS
Remove the 8 screws and windshield outside mouldings.
12. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING
Using a knife, cut off the moulding as shown in the illustration.
NOTICE:
Do not damage the body with the knife.
13. REMOVE WINDSHIELD GLASS
(a) Push piano wire through between the body and glass
from the interior.
(b) Tie both wire ends to wooden blocks or similar objects.
HINT:
Apply protective tape to the outer surface to keep the surface
from being scratched.
NOTICE:
When separating the glass, be careful not to damage the
paint and exterior ornaments. To prevent scratching the
safety pad when removing the windshield, place a plastic
sheet between the piano wire and the safety pad.
(c) Cut the adhesive by pulling the piano wire around it.
(d) Remove the glass.
NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.
Page 3624 of 4323

BO4HK±01
BO4420
Adhesive
BO5231
H12587
H12588
Stopper
A
± BODYWINDSHIELD
BO±63
3616 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. CLEAN AND SHARE CONTACT SURFACE OF BODY
(a) Using a knife, cut away any rough areas on the body.
HINT:
Leave the adhesive on the body as much as possible.
(b) Clean the cut surface of the adhesive with a shop rag sat-
urated in cleaner.
HINT:
Even if the adhesive has been removed, clean the body.
2. CLEAN REMOVE GLASS
(a) Remove the damaged No. 2 stoppers and dams.
(b) Using a scraper, remove the adhesive sticking to the
glass.
(c) Clean the glass with cleaner.
NOTICE:
Be careful not to damage the glass.
Do not touch the glass face after cleaning it.
3. w/ No. 1 stopper:
REPLACE NO. 1 STOPPERS
(a) Remove the damaged stoppers.
(b) Cut off the old adhesive around the stopper installation
area.
NOTICE:
Be careful not to damage the body.
(c) Clean the installation area.
(d) Attach new stoppers to the body so that the notches on
the body will align with the stoppers as shown in the il-
lustration.
HINT:
Make sure that the stoppers are installed facing the correct
direction.
4. INSTALL NEW NO. 2 STOPPERS
Attach new stoppers to the glass so that the ceramic notches
on the glass will align with the stoppers as shown in the illustra-
tion.
HINT:
Make sure that the stoppers are installed facing the correct
direction.
A:
w/ No. 1 stopper: 8.0 mm (0.315 in.)
w/o No. 1 stopper: 8.9 mm (0.350 in.)