Page 2081 of 4323
± DIAGNOSTICSBACK DOOR CONTROL SYSTEM
DI±1879
2073 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check wire harness and connector between back door power window pulse sen-
sor and back door ECU (See page IN±35).
NG Repair or replace wire harness or connector.
OK
Proceed to next circuit inspection shown in
problem symptoms table
(See page DI±1854).
Page 2082 of 4323
I28434
Back Door ECU R16
Rear Wiper Motor
WIP± 4
5L±Y L±O
WIP+ 1
2 B10
B10 R
F DI±1880
± DIAGNOSTICSBACK DOOR CONTROL SYSTEM
2074 Author: Date:
2005 SEQUOIA (RM1146U)
Rear wiper motor circuit
CIRCUIT DESCRIPTION
The wiper motor is controlled by the back door ECU.
WIRING DIAGRAM
DI94K±04
Page 2083 of 4323

± DIAGNOSTICSBACK DOOR CONTROL SYSTEM
DI±1881
2075 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
When using the hand±held tester, start the inspection from step 1 and when not using the hand±held tester,
start from step 2.
1 Check the rear wiper motor using hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
CHECK:
According to the display on the tester, perform the ACTIVE TEST.
BACK±DOOR:
ItemTest detailsDiagnostic note
REAR WIPEROperate the rear wiper motor ON/OFF±
OK:
Rear wiper motor operates normally.
OK Proceed to next circuit inspection shown in
problem symptom table (See page DI±1854).
NG
2 Check rear wiper motor (See page BE±49).
NG Replace the rear wiper motor.
OK
3 Check wire harness and connector between wiper motor and back door ECU
(See page IN±35).
NG Repair or replace wire harness or connector.
OK
Proceed to next circuit inspection shown in
problem symptoms table
(See page DI±1854).
Page 2084 of 4323
I18725
Back Door ECU
BKUL
12G B12
Back Door Key Lock and Unlock SW
3R±W
LKEYE
BKL 5 4 B1019
B10
B10 DI±1882
± DIAGNOSTICSBACK DOOR CONTROL SYSTEM
2076 Author: Date:
2005 SEQUOIA (RM1146U)
Back door key lock and unlock switch circuit
CIRCUIT DESCRIPTION
The back door ECU operates the back door lock motor based on information from the back door key lock
and unlock switch.
The back door power window goes up when the key is inserted into the cylinder and turned to the LOCK
position. The window goes down when the key is turned to the UNLOCK position.
WIRING DIAGRAM
DI94L±05
Page 2085 of 4323

± DIAGNOSTICSBACK DOOR CONTROL SYSTEM
DI±1883
2077 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
When using the hand±held tester, start the inspection from step 1 and when not using the hand±held tester,
start from step 2.
1 Check the back door key lock and unlock switch using hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
CHECK:
According to the display on the tester, read the DATA LIST.
BACK±DOOR:
ItemMeasurement Item/
Display (Range)Normal ConditionDiagnostic Note
KEY SW (UNLOCK)Unlock SW linked with
the key/ON or OFFON: Back door lock is in unlock position
OFF: Back door lock is in lock position±
KEY SW (LOCK)Unlock SW linked with
the key/ON or OFFON: Back door lock is in lock position
OFF: Back door lock is in unlock position±
UP/DOOR KEY
Back door key lock
and unlock switch
linked window open
and close/AVAIL or
NOT AVL
AVAIL: Key±linked open and close SET
NOT AVL: Key±linked open and close UNSET*1
DOWN/DOOR KEY
Back door key lock
and unlock switch
linked window open
and close/AVAIL or
NOT AVL
AVAIL: Key±linked open and close SET
NOT AVL: Key±linked open and close UNSET*1
*1: When the ignition key is not in the key cylinder and the back door is locked, turning and holding the back
door key in the lock position for 1.5 seconds or more activates the back door ECU to operate the power win-
dow motor and close the power window.
Similarly, turning and holding the back door key in the unlock position for 1.5 seconds or more when the back
door is unlocked will open the power window.
OK:
Indication on the tester switches between ON and OFF in accordance with the back door key
lock and unlock switch status.
OK Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1854).
NG
Page 2086 of 4323
DI±1884
± DIAGNOSTICSBACK DOOR CONTROL SYSTEM
2078 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check the back door key lock and unlock switch (See page BE±79).
NG Replace the back door key lock and unlock
switch.
OK
3 Check wire harness and connector between back door key lock and unlock
switch and back door ECU (See page IN±35).
NG Repair or replace wire harness or connector.
OK
Proceed to next circuit inspection shown in
problem symptoms table
(See page DI±1854).
Page 2087 of 4323
I28435
Back Door ECU
P 1
2L±R R16
Rear Wiper Motor
L±B3
3
L±WW
SGND 12
18
B10 B10 B10
P
E W
± DIAGNOSTICSBACK DOOR CONTROL SYSTEM
DI±1885
2079 Author: Date:
2005 SEQUOIA (RM1146U)
Rear wiper limit switch circuit
CIRCUIT DESCRIPTION
The rear wiper limit switch is built in to the rear wiper motor. The W built in switch of the rear wiper motor is
ON when the rear wiper arm is in the position between stop and reverse and OFF when the rear wiper arm
is in any other position. The P built in switch of the rear wiper motor is OFF when the rear wiper arm is in
any position except stored and ON when the rear wiper arm is in the stored position.
WIRING DIAGRAM
DI94J±04
Page 2088 of 4323
DI±1886
± DIAGNOSTICSBACK DOOR CONTROL SYSTEM
2080 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check rear wiper motor (See page BE±49).
NG Replace the rear wiper motor.
OK
2 Check wire harness and connector between rear wiper motor and back door ECU
(See page IN±35).
NG Repair or replace wire harness or connector.
OK
Proceed to next circuit inspection shown in
problem symptoms table
(See page DI±1854).