2001 TOYOTA SEQUOIA Service Repair Manual

bonnet adblue reset keyless oil reset adblue sport mode

Page 241 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual ± DIAGNOSTICSENGINE
DI±47
241 Author: Date:
2005 SEQUOIA (RM1146U)P2120
P2121
P2122
P2123
P2125
P2127
P2128
P2138
The accelerator pedal position sensor has two (main and
sub) sensor circuits. If

Page 242 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DID81±01
DI±48
± DIAGNOSTICSENGINE
242 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
By reading the DATA LIST displayed on a hand±held tester, you can check v

DID81±01
DI±48
± DIAGNOSTICSENGINE
242 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
By reading the DATA LIST displayed on a hand±held tester, you can check values, including those of the
switches, sensors, and actuators, without removing any parts. Reading the DATA LIST as the first step of
troubleshooting is one method of shortening diagnostic time.
NOTICE:
In the table below, the values listed under Normal Conditions are for reference only. Do not depend
solely on these values when determining whether or not a part is faulty.
(a) Warm up the engine.
(b) Turn the ignition switch to OFF.
(c) Connect a hand±held tester to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the tester ON.
(f) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST.
(g) Check the values by referring to the table below.
Hand±Held Tester DisplayMeasurement Item:Range
(Display)Normal Condition *Diagnostic Note
INJECTOR
Injection period of the No. 1 cylin-
der:
Min.: 0 ms, Max.: 32.64 ms
2.3 to 3.8 ms: Idling'
IGN ADVANCE
Ignition timing advance for No. 1
cylinder/
Min.: ±64 deg., Max.: 63.5 deg.
BTDC 4 to 17°: Idling'
CALC LOADCalculated load by ECM:
Min.: 0 %, Max.: 100 %11 to 21 %: Idling
12 to 22 %: Running without load
(2,500 rpm)
'
VEHICLE LOADVehicle load:
Min.: 0 %, Max.: 25700 %Actual vehicle load'
MAFAir flow rate from MAF meter:
Min.: 0 g/s, Max.: 655 g/s2.0 to 3.9 g/s: Idling
If the value approximately 0.0 g/s:
Mass air flow meter power
source circuit open
VG circuit open or short
If the value 160.0 g/s or more:
E2G circuit open
ENGINE SPDEngine speed:
Min.: 0 rpm, Max.: 16,383 rpm600 50 rpm: Idling'
VEHICLE SPDVehicle speed:
Min.: 0 km/h, Max.: 255 km/hActual vehicle speedSpeed indicated on speedometer
COOLANT TEMPEngine coolant temperature:
Min.: ±40C, Max.: 140C80 to 100°C
(176 to 212°F): After warming up
If the value ±40C (±40F): sen-
sor circuit open
If the value 140C (284F): sen-
sor circuit shorted
INTAKE AIRIntake air temperature:
Min.: ±40C, Max.: 140CEquivalent to ambient air tempera-
ture
If the value ±40C (±40F): sen-
sor circuit open
If the value 140C (284F): sen-
sor circuit shorted
SECONDARY AIRSecond air system status:
ON or OFFON: Secondary air system opera-
tion'
AIR±FUEL RATIOAir±fuel ratio:
Min.: 0, Max.: 1.9990.8 to 1.2: During idling'
EVAP VAPOR PRESEVAP vapor pressure:
Min.: ±8192 Pa, Max.: 8191 Pa0 Pa: Fuel tank cap removed'

Page 243 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual ± DIAGNOSTICSENGINE
DI±49
243 Author: Date:
2005 SEQUOIA (RM1146U)PURGE DENSITY
Learning value of purge density/
Min.: ±50, Max.: 350Idling: ±40 to 0 %Service data
PURGE FLOWPurge flow:
Min.:

± DIAGNOSTICSENGINE
DI±49
243 Author: Date:
2005 SEQUOIA (RM1146U)PURGE DENSITY
Learning value of purge density/
Min.: ±50, Max.: 350Idling: ±40 to 0 %Service data
PURGE FLOWPurge flow:
Min.: 0 %, Max.: 102.4 %0 to 100 %: Idling'
EVAP PURGE VSVEVAP (Purge) VSV control duty:
Min.: 0 %, Max.: 100 %0 to 100 %: During idlingOrder signal from ECM
VAPOR PRESSVapor pressure:
Min.: ±4.125 kPa, Max.: 2.125 kPa0 kPa: Fuel tank cap removed
Pressure inside fuel tank moni-
tored by the vapor pressure sen-
sor
KNOCK CRRT VAL
Correction learning value of
knocking:
Min.: ±64 CA, Max.: 1,984 CA0 to 22 CA:
Driving, 44 mph (70 km/h)Service data
KNOCK FB VALFeedback value of knocking:
Min.: ±64 CA, Max.: 1,984 CA±22 to 0 CA
Driving, 44 mph (70 km/h)Service data
ACCEL POS #1
Absolute Accelerator Pedal Posi-
tion (APP) No. 1:
Min.: 0 %, Max.: 100 %10 to 22 %: accelerator pedal is
released
54 to 86 %: accelerator pedal is
fully depressed
'
ACCEL POS #2Absolute APP No. 2:
Min.: 0 %, Max.: 100 %
12 to 42 %: accelerator pedal is
released
66 to 98 %: The accelerator pedal
is fully depressed
'
ACCEL POS #1APP sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V'ETCS freeze data
ACCEL POS #2APP sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V'ETCS freeze data
ACCEL POS #1APP sensor No. 1 voltage:
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: accelerator pedal is
released.
2.6 to 4.5 V: or pedal is fully de-
pressed.
'
ACCEL POS #2APP sensor No. 2 voltage:
Min.: 0 V, Max.: 5 V
1.2 to 2.0 V: accelerator pedal is
released.
3.4 to 5.3 V: accelerator pedal is
fully depressed.
'
ACCEL IDL POS
Whether or not accelerator pedal
position sensor detecting idle:
ON or OFF
ON: Idling'
THRTL LEARN VAL
Throttle valve fully closed
(learned value):
0.4 to 0.8 V'
ACCEL SSR #1 AD
Accelerator fully closed value No.1
(AD):
Min.: 0, Max.: 4.98 V
'ETCS service data
ACCEL LRN VAL#1
Accelerator fully closed learning
value No.1:
Min.: 0, Max.: 124.512
'ETCS service data
ACCEL LRN VAL#2
Accelerator fully closed learning
value No.2:
Min.: 0, Max.: 124.512
'ETCS service data
FAIL #1
Whether or not fail safe function
executed:
ON or OFF
ON: ETCS has failed'
FAIL #2
Whether or not fail safe function
executed:
ON or OFF
ON: ETCS has failed'

Page 244 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DI±50
± DIAGNOSTICSENGINE
244 Author: Date:
2005 SEQUOIA (RM1146U)ST1
Starter signal:
ON or OFFON: Cranking
SYSGUARD JUDGESystem guard:
ON or OFFETCS service data
OPN MALFUNCTIONOpen side mal

DI±50
± DIAGNOSTICSENGINE
244 Author: Date:
2005 SEQUOIA (RM1146U)ST1
Starter signal:
ON or OFFON: Cranking'
SYSGUARD JUDGESystem guard:
ON or OFF'ETCS service data
OPN MALFUNCTIONOpen side malfunction:
ON or OFF'ETCS service data
THROTTLE POSAbsolute throttle position sensor:
Min.: 0 %, Max.: 100 %10 to 24 %: Throttle fully closed
64 to 96 %: Throttle fully openRead the value with intrusive op-
eration (active test)
THROTTL IDL POS
Whether or not throttle position
sensor detecting idle:
ON or OFF
ON: Idling'
THRTL REQ POSThrottle requirement position:
Min.: 0 V, Max.: 5 V0.5 to 1.0 V: Idling'
THROTTLE POSThrottle sensor positioning:
Min.: 0 %, Max.: 100 %10 to 18 %: IdlingCalculated value based on VTA1
THROTTLE POS #2Throttle sensor positioning #2:
Min.: 0 %, Max.: 100 %'Calculated value based on VTA2
THROTTLE POS #1
Throttle position sensor No. 1
output voltage:
Min.: 0 V, Max.: 4.9 V
'ETCS freeze data
THROTTLE POS #2
Throttle position sensor No.2 out-
put voltage:
Min.: 0 V, Max.: 4.9 V
'ETCS freeze data
THROTTLE POS #1Throttle position No. 1:
Min.: 0 V, Max.: 5 V0.5 to 1.2 V: Throttle fully closed
3.2 to 4.8 V: Throttle fully opened'
THROTTLE POS #2Throttle position No. 2:
Min.: 0 V, Max.: 5 V2.0 to 2.9 V: Throttle fully closed
4.6 to 5.5 V: Throttle fully openRead the value with intrusive op-
eration (active test)
THRTL COMND VALThrottle position command value:
Min.: 0 V, Max.: 4.98 V0.5 to 4.8 VETCS service data
THROTTLE SSR #1
Throttle sensor opener position
No. 1:
Min.: 0 V, Max.: 4.98 V
0.6 to 0.9 VETCS service data
THROTTLE SSR #2
Throttle sensor opener position
No. 2:
Min.: 0 V, Max.: 4.98 V
2.2 to 2.6 VETCS service data
THRTL SSR #1 AD
Throttle sensor opener position
No.1 (AD):
Min.: 0 V, Max.: 4.98 V
0.6 to 0.9 VETCS service data
THROTTLE MOT
Whether or not throttle motor con-
trol permitted:
ON or OFF
ON: IdlingRead the value with the power
switch ON (Do not start engine)
THROTTLE MOTThrottle motor current:
Min.: 0 A, Max.: 80 A0 to 3.0 A: Idling'
THROTTLE MOTThrottle motor:
Min.: 0 %, Max.: 100 %0.5 to 40 %: Idling'
THROTTLE MOTThrottle motor current:
Min.: 0 A, Max.: 19.92 A0 to 3.0 A: Idling'
THROTL OPN DUTYThrottle motor opening duty ratio:
Min.: 0 %, Max.: 100 %0 to 40 %: During idlingWhen accelerator pedal de-
pressed, duty ratio increased
THROTL CLS DUTYThrottle motor closed duty ratio:
Min.: 0 %, Max.: 100 %0 to 40 %: During idlingWhen accelerator pedal released
quickly, duty ratio increased
THRTL MOT (OPN)Throttle motor duty ratio (open):
Min.: 0 %, Max.: 100 %'ETCS service data

Page 245 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual ± DIAGNOSTICSENGINE
DI±51
245 Author: Date:
2005 SEQUOIA (RM1146U)THRTL MOT (CLS)
Throttle motor duty ratio (close):
Min.: 0 %, Max.: 100 %ETCS service data
O2S B1 S2
Heated oxygen sensor outpu

± DIAGNOSTICSENGINE
DI±51
245 Author: Date:
2005 SEQUOIA (RM1146U)THRTL MOT (CLS)
Throttle motor duty ratio (close):
Min.: 0 %, Max.: 100 %'ETCS service data
O2S B1 S2
Heated oxygen sensor output volt-
age for bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V0.1 to 0.9 V:
Driving 44 mph (70 km/h)
Performing the INJ VOL or A/F
CONTROL function of the ACTIVE
TEST enables the technician to
check voltage output of the sensor
O2S B2 S2
Heated oxygen sensor output volt-
age for bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V0.1 to 0.9 V:
Driving 44 mph (70 km/h)
Performing the INJ VOL or A/F
CONTROL function of the ACTIVE
TEST enables the technician to
check voltage output of the sensor
AFS B1 S1
A/F sensor output voltage for bank
1 sensor 1:
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing the INJ VOL or A/F
CONTROL function of the ACTIVE
TEST enables the technician to
check voltage output of the sensor
AFS B2 S1
A/F sensor output voltage for bank
1 sensor 1:
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing the INJ VOL or A/F
CONTROL function of the ACTIVE
TEST enables the technician to
check voltage output of the sensor
TOTAL FT #1
Total fuel trim of bank 1
Average value for fuel trim system
of bank 1:
Min.: ±0.5, Max.: 1,496
±0.2 to 0.2: Idling'
TOTAL FT #2
Total fuel trim of bank 1
Average value for fuel trim system
of bank 1:
Min.: ±0.5, Max.: 1,496
±0.2 to 0.2: Idling'
SHORT FT #1Short±term fuel trim of bank 1:
Min.: ±100 %, Max.: 99.2%0 ± 20 %
This item the short±term fuel com-
pensation used to maintain the
air±fuel ratio at stoichiometric air±
fuel ratio
SHORT FT #2Short±term fuel trim of bank 1:
Min.: ±100 %, Max.: 99.2%0 ± 20 %
This item the short±term fuel com-
pensation used to maintain the
air±fuel ratio at stoichiometric air±
fuel ratio
LONG FT #1Long±term fuel trim of bank 1:
Min.: ±100 %, Max.: 99.2 %0 ± 20 %
This item the overall fuel com-
pensation carried out in long±term
to compensate a continual devi-
ation of the short±term fuel trim
from the central value
LONG FT #2Long±term fuel trim of bank 1:
Min.: ±100 %, Max.: 99.2 %0 ± 20 %
This item the overall fuel com-
pensation carried out in long±term
to compensate a continual devi-
ation of the short±term fuel trim
from the central value
FUEL SYS #1
Fuel system status (Bank1):
OL or CL or OL DRIVE or
OL FAULT or CL FAULT
CL: Idling after warming up
OL (Open Loop): Has not yet sa-
tisfied conditions to go closed
loop
CL (Closed Loop): Using heated
oxygen sensor as feedback for
fuel control.
OL DRIVE: Open loop due to
driving conditions (fuel enrich-
ment)
OL FAULT: Open loop due to de-
tected system fault
CL FAULT: Closed loop but
heated oxygen sensor, which
used for fuel control malfunction-
ing

Page 246 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DI±52
± DIAGNOSTICSENGINE
246 Author: Date:
2005 SEQUOIA (RM1146U)FUEL SYS #2
Fuel system status (Bank1):
OL or CL or OL DRIVE or
OL FAULT or CL FAULT
CL: Idling after warming up
OL (Open Loop)

DI±52
± DIAGNOSTICSENGINE
246 Author: Date:
2005 SEQUOIA (RM1146U)FUEL SYS #2
Fuel system status (Bank1):
OL or CL or OL DRIVE or
OL FAULT or CL FAULT
CL: Idling after warming up
OL (Open Loop): Has not yet sa-
tisfied conditions to go closed
loop
CL (Closed Loop): Using heated
oxygen sensor as feedback for
fuel control.
OL DRIVE: Open loop due to
driving conditions (fuel enrich-
ment)
OL FAULT: Open loop due to de-
tected system fault
CL FAULT: Closed loop but
heated oxygen sensor, which
used for fuel control malfunction-
ing
O2FT B1 S2
Short±term fuel trim associated
with the bank 1 sensor 2:
Min.: ±100 %, Max.: 99.2 %
0 ± 20 %Same as SHORT FT #1
O2FT B2 S2
Short±term fuel trim associated
with the bank 1 sensor 2:
Min.: ±100 %, Max.: 99.2 %
0 ± 20 %Same as SHORT FT #1
AF FT B1 S1
Short±term fuel trim associated
with the bank 1 sensor 1:
Min.: 0, Max.: 1.999
Value less than 1 (0.000 to
0.999) = Lean
Stoichiometric air±fuel ratio=1
Value greater than 1 (1.001 to
1.999) = RICH
'
AF FT B2 S1
Short±term fuel trim associated
with the bank 1 sensor 1:
Min.: 0, Max.: 1.999
Value less than 1 (0.000 to
0.999) = Lean
Stoichiometric air±fuel ratio=1
Value greater than 1 (1.001 to
1.999) = RICH
'
CAT TEMP B1S1
Catalyst temperature (Bank 1,
Sensor 1):
Min.: ±40, Max.: 6,513.5 C
''
CAT TEMP B2S1
Catalyst temperature (Bank 1,
Sensor 1):
Min.: ±40, Max.: 6,513.5 C
''
CAT TEMP B1S2
Catalyst temperature (Bank 1,
Sensor 2):
Min.: ±40, Max.: 6,513.5 C
''
CAT TEMP B2S2
Catalyst temperature (Bank 1,
Sensor 2):
Min.: ±40, Max.: 6,513.5 C
''
INI COOL TEMPInitial engine coolant temperature:
Min.: ±40C, Max.: 140CClose to ambient air temperatureService data
INI INTAKE TEMPInitial intake air temperature:
Min.: ±40C, Max.: 140CClose to ambient air temperatureService data
INJ VOLInjection volume (cylinder 1):
Min.: 0 ml, Max.: 2.048 ml0 to 0.5 mlQuantity of fuel injection volume
for 10 times
STARTER SIGStarter signal: ON or OFFON: Cranking'
PS SWPower steering signal:
ON or OFFON: Power steering operation'
PS SIGNALPower steering signal:
ON or OFFON: When steering wheel first
turned after ignition switch turned
to ONThis signal status usually ON until
ignition switch turned to OFF
CTP SWClosed throttle position switch:
ON or OFFON: Throttle fully closed
OFF: Throttle open'

Page 247 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual ± DIAGNOSTICSENGINE
DI±53
247 Author: Date:
2005 SEQUOIA (RM1146U)A/C SIG
A/C signal: ON or OFFON: A/C ON
ELECT LOAD SIGElectrical load signal:
ON or OFFON: Headlights or defogger is
turned ON

± DIAGNOSTICSENGINE
DI±53
247 Author: Date:
2005 SEQUOIA (RM1146U)A/C SIG
A/C signal: ON or OFFON: A/C ON'
ELECT LOAD SIGElectrical load signal:
ON or OFFON: Headlights or defogger is
turned ON'
STOP LIGHT SWStop lamp switch:
ON or OFFON: brake pedal is depressed.'
+BM
Whether or not electric throttle
control system power inputted:
ON or OFF
ON: Idling'
+BM VOLTAGE+BM voltage:
Min.: 0, Max.: 19.9210 to 15 V: IdlingETCS service data
BATTERY VOLTAGEBattery voltage:
Min.: 0 V, Max.: 65.535 V9 to 14 V: Idling'
ACTUATOR POWERActuator power supply:
ON or OFFON: IdlingETCS service data
ATM PRESSUREAtmospheric pressure:
Min.: 0 kPa, Max.: 150 kPaEquivalent to atmospheric pres-
sure (absolute pressure)'
SECOND AIR VSVSecondary air injection system
statusON: Secondary air injection sys-
tem operation'
ACT VSVA/C cut status for Active Test:
ON or OFF'Active Test support data
EVAP (Purge) VSVVSV status for EVAP control:
ON or OFF'Active Test support data
FUEL PUMP / SPDFuel pump/speed status:
ON or OFF'Active Test support data
VVT CTRL B1VVT control status:
ON or OFF'Active Test support data
VVT CTRL B2VVT control status:
ON or OFF'Active Test support data
VACUUM PUMP
Key±off EVAP system pump sta-
tus:
ON or OFF
'Active Test support data
EVAP VENT VAL
Key±off EVAP system vent valve
status:
ON or OFF
'Active Test support data
TC/TE1TC and TE1 terminal of DLC3:
ON or OFF''
VVTL AIM ANGL #1VVT aim angle (bank 1):
Min.: 0 %, Max.: 100 %0 %: IdlingVVT duty signal value during intru-
sive operation
VVTL AIM ANGL #2VVT aim angle (bank 1):
Min.: 0 %, Max.: 100 %0 %: IdlingVVT duty signal value during intru-
sive operation
VVT CHNG ANGL #1VVT change angle:
Min.: 0FR, Max.: 60FR0 to 5 FR: IdlingDisplacement angle during intru-
sive operation
VVT CHNG ANGL #2VVT change angle:
Min.: 0FR, Max.: 60FR0 to 5 FR: IdlingDisplacement angle during intru-
sive operation
VVT OCV DUTY B1VVT OCV operation duty:
Min.: 0 %, Max.: 100 %0 %: IdlingRequested duty value for intrusive
operation
VVT OCV DUTY B2VVT OCV operation duty:
Min.: 0 %, Max.: 100 %0 %: IdlingRequested duty value for intrusive
operation
FC IDLFuel cut idle:
ON or OFFON: Fuel cut operation
FC IDL = ºONº when throttle valve
fully closed and engine speed over
2,800 rpm

Page 248 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DI±54
± DIAGNOSTICSENGINE
248 Author: Date:
2005 SEQUOIA (RM1146U)FC TAU
Fuel cut TAU: Fuel cut during very
light load:
ON or OFF
ON: Fuel cut operating
The fuel cut being performed un-
der very

Load next 8 pages

Page: < prev 1-10 ... 209-216 217-224 225-232 233-240 241-248 249-256 257-264 265-272 273-280 ... 4328 next >

power steering fluid ECO mode tow bar turn signal bulb compression ratio ground clearance