Page 3545 of 4323
BE0G4±01
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE±133
3537 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE FRONT PERSONAL LIGHT LENS
2. REMOVE FRONT PERSONAL LIGHT
(a) Remove the 3 screws.
(b) Disconnect the 2 connectors.
3. REMOVE GARAGE DOOR OPENER SWITCH
Page 3546 of 4323

I18597
BE26F±03
I18598
I18599
BE±134
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
3538 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT GARAGE DOOR OPENER SWITCH
(a) Press the switch and check that each garage door indica-
tor (green) comes on.
(b) Even if only one switch does not come on, replace it.
2. INSPECT GARAGE DOOR OPENER REGISTRATION
AND TRANSMITTING
HINT:
Use the home link tester made by KENT MORE for this test.
As it is necessary to record the code of the hand held transmit-
ter, customer's code will be erased. When the inspection is
complete, please register the customer's again.
(a) Check that the inspection code of the hand held transmit-
ter can be recorded (See page BE±129).
If the code can not be registered, replace the garage door open-
er.
(b) Press the switch which an inspection code has been reg-
istered for and check that garage door indicator (green)
of the home link tester comes on.
If the garage door indicator (green) does not come on, replace
the garage door opener.
Page 3547 of 4323
I21538
Wire Harness Side:
I21537
Wire Harness Side:
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE±135
3539 Author: Date:
2005 SEQUOIA (RM1146U)
3. w/ Sliding Roof:
INSPECT GARAGE DOOR OPENER SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
1 ± GroundAlwaysContinuity
3 ± GroundAlwaysBattery positive voltage
If the circuit is not as specified, inspect the power source or wire
harness.
4. w/o Sliding Roof:
INSPECT GARAGE DOOR OPENER SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
9 ± GroundAlwaysBattery positive voltage
13 ± GroundAlwaysContinuity
If the circuit is not as specified, inspect the power source or wire
harness.
Page 3548 of 4323
BE0G6±01
BE±136
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
3540 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. INSTALL GARAGE DOOR OPENER
2. INSTALL FRONT PERSONAL LIGHT
(a) Connect the 2 connectors.
(b) Install the 3 screws.
3. INSTALL FRONT PERSONAL LIGHT LENS
Page 3549 of 4323

START
Insert the key in the key cylinder.
Under registration
Registration completion
Remove the key.
Will you register the
next key?
NoSecurity indicator blinks until the first
key is inserted. The indicator comes
on after the key registration.
Security Indicator
OFF
END Ye s
Security Indicator ON
(After the last key (sub±key) has been
registered, the indicator remains OFF
until the key is removed. After the key
is removed, the indicator blinks.)
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±137
3541 Author: Date:
2005 SEQUOIA (RM1146U)
ENGINE IMMOBILISER SYSTEM
REGISTRATION PROCEDURE
HINT:
If you lose all the registered master keys, you cannot registrar or delete additionally. Change the transponder
key ECU and then register the new key codes following the registration procedure of the automatic registra-
tion mode below.
1. KEY REGISTRATION IN AUTOMATIC REGISTRATION MODE
(a) Registration of a new transponder key.
HINT:
This procedure must be done when you install a new transponder key ECU.
The new transponder key ECU is in automatic key code registration mode. The key codes already fixed
for this transponder key ECU can be registered.
For this type of vehicle, up to 3 key codes can be registered.
In the automatic registration mode, the last key registered becomes a sub±key.
Page 3550 of 4323

1.8 Sec.
0.2 Sec.
0.25 Sec. 0.5 Sec.0.25 Sec.
1 Sec. Blinks
Code 2±1 Code 2±2
0.25 Sec.
0.25 Sec.0.5 Sec. 1 Sec. BE±138
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
3542 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:
When a key cannot be inserted in the key cylinder in automatic registration mode, the security indicator
always comes on.
When the immobilizer system operates normally and the key is pull out, the security indicator blinks.
When key code registration could not be performed in automatic registration mode, code 2±1 is output
from the security indicator and when the registered key in inserted, code 2±2 is output.
(b) Automatic registration mode completion
If completing the mode forcibly when more than 1 key codes are registered in automatic registration
mode, perform the following procedures.
After 1 more key codes are registered with the master key, turn the ignition switch LOCK "ON 5 times
within 10 secs. by inserting the registered key or without pulling the key out.
Page 3551 of 4323
START
END
All doors closed. No key in the key cylinder.
Insert the registered master key in the key cylinder.
Ignition switch: LOCK " ON 5 times
Driver's door: Open " Close 6 times
Remove the master key.
Insert the key to be registered in the key cylinder.
Keep ignition switch in ON position for 60 seconds or more.
Remove the master key.
Do you register another key?
Driver's door: Open " Close
within
15 secs.
within
20 secs.
within
10 secs.
within
10 secs.
within
10 secs.*6
*5 *4 *3 *2 *1
No Ye s
10 secs.
or
more
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±139
3543 Author: Date:
2005 SEQUOIA (RM1146U)
2. REGISTRATION OF ADDITIONAL MASTER KEY AND SUB KEY
Do this operation to register an additional master key and sub key.
Page 3552 of 4323

BE±140
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
3544 Author: Date:
2005 SEQUOIA (RM1146U)
*1: Insert the master key into the key cylinder.
Turn the ignition switch to the LOCK " ON position 5 times within 15 seconds.
*2: Open and close the driver's door 6 times within 20 seconds after completion of the previous operation.
*3: Remove the master key from the ignition switch and insert another key to be registered in the key cylinder
within 10 seconds after completion of the previous operation.
*4: Turn the ignition switch to the ON position and wait for 60 seconds or more, then key registration will be
completed.
*5: 10 seconds or more elapse after removal of the key or open and close the driver's door, then key registra-
tion will be completed.
*6: When registering multiple keys, insert the key to be registered in the key cylinder.
HINT:
It is possible to register up to 4 master key codes including the registered key code.
It is possible to register up to 2 sub key codes including the registed key code.
When any operation time described above is over, registration mode completes.
When the next procedure is performed while the timer is working, the timer completes counting time,
then the next timer starts.