2001 TOYOTA SEQUOIA fuel cap release

DI±30
± DIAGNOSTICSENGINE
224 Author: Date:
2005 SEQUOIA (RM1146U)
(a) Preconditions
The monitor will not run unless:

MIL is OFF

Fuel level is approximately 1/2 to 3/4

Altitude is 7,800 feet (2,400 m) or less

Engine Coolant Temperature (ECT) is between 4.4°C and 35°C (40°F and 95°F)

Intake Air Temperature (IAT) is between 4.4°C and 35°C (40°F and 95°F)

Cold Soak Procedure has been completed

Before starting the engine, the difference between ECT and IAT must be less than 7°C (13°F)
HINT:
Examples:

Scenario 1
ECT = 24°C (75°F)
IAT = 16°C (60°F)
Difference between ECT and IAT is 8°C (15°F)
" The monitor will not run because difference between ECT and IAT is higher than 7°C (13°F)

Scenario 2
ECT = 21°C (70°F)
IAT = 20°C (68°F)
Difference between ECT and IAT is 1°C (2°F)
" The monitor will run because difference between ECT and IAT is less than 7°C (13°F)
The readiness test can be completed in cold ambient conditions (less than 40°F / 4.4°C) and/or at
high altitudes (more than 7,800 feet / 2,400 m) if the drive pattern is repeated a second time after cycl-
ing the ignition off.
(b) Drive Pattern
(1) Connect the OBD II scan tool to DLC3 to check monitor status and preconditions (refer to (a)).
(2) Release pressure in fuel tank by removing the fuel tank cap and then reinstall it.
(3) Start the engine and allow it to idle until ECT becomes 75°C (167°F) or higher.
(4) Run the engine at 3,000 rpm for approximately 10 seconds.
(5) Allow the engine to idle with the A/C ON (to create slight load) for 15 to 50 minutes.
NOTICE:
If the vehicle is not equipped with A/C, put a slight load on the engine by doing the following :

Securely set the parking brake.

Block the drive wheels with wheel chocks.

Allow the vehicle to idle in drive for 15 to 50 minutes.

± DIAGNOSTICSENGINE
DI±49
243 Author: Date:
2005 SEQUOIA (RM1146U)PURGE DENSITY
Learning value of purge density/
Min.: ±50, Max.: 350Idling: ±40 to 0 %Service data
PURGE FLOWPurge flow:
Min.: 0 %, Max.: 102.4 %0 to 100 %: Idling'
EVAP PURGE VSVEVAP (Purge) VSV control duty:
Min.: 0 %, Max.: 100 %0 to 100 %: During idlingOrder signal from ECM
VAPOR PRESSVapor pressure:
Min.: ±4.125 kPa, Max.: 2.125 kPa0 kPa: Fuel tank cap removed
Pressure inside fuel tank moni-
tored by the vapor pressure sen-
sor
KNOCK CRRT VAL
Correction learning value of
knocking:
Min.: ±64 CA, Max.: 1,984 CA0 to 22 CA:
Driving, 44 mph (70 km/h)Service data
KNOCK FB VALFeedback value of knocking:
Min.: ±64 CA, Max.: 1,984 CA±22 to 0 CA
Driving, 44 mph (70 km/h)Service data
ACCEL POS #1
Absolute Accelerator Pedal Posi-
tion (APP) No. 1:
Min.: 0 %, Max.: 100 %10 to 22 %: accelerator pedal is
released
54 to 86 %: accelerator pedal is
fully depressed
'
ACCEL POS #2Absolute APP No. 2:
Min.: 0 %, Max.: 100 %
12 to 42 %: accelerator pedal is
released
66 to 98 %: The accelerator pedal
is fully depressed
'
ACCEL POS #1APP sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V'ETCS freeze data
ACCEL POS #2APP sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V'ETCS freeze data
ACCEL POS #1APP sensor No. 1 voltage:
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: accelerator pedal is
released.
2.6 to 4.5 V: or pedal is fully de-
pressed.
'
ACCEL POS #2APP sensor No. 2 voltage:
Min.: 0 V, Max.: 5 V
1.2 to 2.0 V: accelerator pedal is
released.
3.4 to 5.3 V: accelerator pedal is
fully depressed.
'
ACCEL IDL POS
Whether or not accelerator pedal
position sensor detecting idle:
ON or OFF
ON: Idling'
THRTL LEARN VAL
Throttle valve fully closed
(learned value):
0.4 to 0.8 V'
ACCEL SSR #1 AD
Accelerator fully closed value No.1
(AD):
Min.: 0, Max.: 4.98 V
'ETCS service data
ACCEL LRN VAL#1
Accelerator fully closed learning
value No.1:
Min.: 0, Max.: 124.512
'ETCS service data
ACCEL LRN VAL#2
Accelerator fully closed learning
value No.2:
Min.: 0, Max.: 124.512
'ETCS service data
FAIL #1
Whether or not fail safe function
executed:
ON or OFF
ON: ETCS has failed'
FAIL #2
Whether or not fail safe function
executed:
ON or OFF
ON: ETCS has failed'

DI±490
± DIAGNOSTICSENGINE
684 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Monitor Conditions
(1) Allow the engine to idle for at least 5 minutes.
(2) Turn the ignition switch to OFF and wait for 6 hours (8 or 10.5 hours).
HINT:
Do not start the engine until checking MONITOR STATUS. If the engine is started, the steps described above
must be repeated.
(c) Monitor Status
(1) Connect a hand±held tester to the DLC3.
(2) Turn the ignition switch to ON and turn the tester ON.
(3) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / MONITOR
STATUS.
(4) Check the Monitor Status displayed on the tester.
HINT:
If INCMP is displayed, the monitor is not completed. Make sure that the preconditions have been met, and
perform the Monitor Conditions again.
2. PURGE FLOW MONITOR CONFIRMATION (P0441)
HINT:
Perform this monitor confirmation after the Key±Off Monitor Confirmation shows COMPL (complete).
(a) Preconditions
The monitor will not run unless:

The vehicle has been driven for 10 minutes or more (in a city area or on a free way)

The ECT is between 4.4C and 35C (40F and 95F)

The IAT is between 4.4C and 35C (40F and 95F)
(b) Monitor Conditions
(1) Release the pressure from the fuel tank by removing and reinstalling the fuel tank cap.
(2) Warm the engine up until the ECT reaches more than 75C (167F).
(3) Increase the engine speed to 3,000 rpm once.
(4) Allow the engine to idle and turn A/C ON for 1 minute.
(c) Monitor Status
(1) Turn the ignition switch to OFF (where ON or the engine is running).
(2) Connect a hand±held tester to the DLC3.
(3) Turn the ignition switch to ON and turn the tester ON.
(4) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / MONITOR
STATUS.
(5) Check the Monitor Status displayed on the tester.
HINT:
If INCMP is displayed, the monitor is not completed. Make sure that the preconditions have been met, and
perform the Monitor Conditions again.

05_SEQUOIA_U (L/O 0408)
364
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)

Four±wheel drive models onlyÐToyota
recommends not using four±wheel drive
on dry hard±surfaced roads, because
four±wheel driving will cause unneces-
sary noise and wear, and poor fuel
economy.

Four±wheel drive models onlyÐIn cold
temperatures, noise may occur when
driving in two±wheel drive before the
transfer is warmed up. Therefore, first
drive in four±wheel drive until the
transfer is warmed up.

Vehicles with rear height control air
suspension: When driving on a bumpy
road, set the vehicle height to ªHIº in
automatic control mode, then select
manual control mode by pushing the
mode select switch. You should drive
at a speed of less than 30 km/h (18
mph).
CAUTION

Before driving off, make sure that
the parking brake is fully released
and the parking brake reminder
light is off.

Do not leave your vehicle unat-
tended while the engine is running.

Do not rest your foot on the brake
pedal while driving. It can cause
dangerous overheating, needless
wear, and poor fuel economy.

To drive down a long or steep hill,
reduce your speed and downshift.
Remember, if you ride the brakes
excessively, they may overheat and
not work properly.

Be careful when accelerating, up-
shifting, downshifting or braking on
a slippery surface. Sudden accelera-
tion or engine braking, could cause
the vehicle to skid or spin.

Do not drive in excess of the speed
limit. Even if the legal speed limit
permits it, do not drive over 140
km/h (85 mph) unless your vehicle
has high±speed capability tires.
Driving over 140 km/h (85 mph) may
result in tire failure, loss of control
and possible injury. Be sure to con-
sult a tire dealer to determine
whether the tires on your vehicle
are high±speed capability tires or
not before driving at such speeds.

Do not continue normal driving
when the brakes are wet. If they are
wet, your vehicle will require a
longer stopping distance, and it
may pull to one side when the
brakes are applied. Also, the park-
ing brake will not hold the vehicle
securely.