2001 TOYOTA SEQUOIA ground clearance

SS0OJ±22
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS±31
173 Author: Date:
2005 SEQUOIA (RM1146U)
SUSPENSION AND AXLE
SERVICE DATA
Tire size: P245/70R16 Front
Rear220 kPa (2.2 kgf/cm2, 32 psi)
240 kPa (2.4 kgf/cm2, 35 psi)
Cold tire inflation
pressureTire size: P265/70R16 Front
Rear220 kPa (2.2 kgf/cm2, 32 psi)
220 kPa (2.2 kgf/cm2, 32 psi)ressure
Tire size: P265/65R17 Front
Rear220 kPa (2.2 kgf/cm2, 32 psi)
220 kPa (2.2 kgf/cm2, 32 psi)
Vehicle height (Except air suspension models)
UCK35L±GKBSKA
Tire size: P245/70R16 Front:
A*1 ± B*2
Rear: C*3 ± D*4
Tire size: P265/70R16 and P265/65R17
Front:
A*1 ± B*2
Rear: C*3 ± D*4
69.7 mm (2.74 in.)
76.2 mm (3.00 in.)
69.5 mm (2.74 in.)
75.5 mm (2.97 in.)
UCK35L±GKBLKA Front:
A*1 ± B*2
Rear: C*3 ± D*471.6 mm (2.82 in.)
77.3 mm (3.04 in.)
UCK45L±GKBSKA Front:
A*1 ± B*2
Rear: C*3 ± D*461.6 mm (2.43 in.)
63.8 mm (2.51 in.)
Front wheel
UCK45L±GKBLKA Front:
A*1 ± B*2
Rear: C*3 ± D*462.8 mm (2.47 in.)
65.2 mm (2.57 in.)
Front wheel
Alignment
Vehicle height (Except air suspension models)g
UCK35L±GKBSKA
Tire size: P245/70R16 Front:
A*1 ± B*2
Rear: C*3 ± D*4
Tire size: P265/70R16 and P265/65R17
Front:
A*1 ± B*2
Rear: C*3 ± D*4
53.5 ± 83.5 mm (2.11 ± 3.29 in.)
74.8 ± 104.8 mm (2.94 ± 4.13 in.)
53.3 ± 83.3 mm (2.10 ± 3.28 in.)
74.1 ± 104.1 mm (2.92 ± 4.10 in.)
UCK35L±GKBLKA Front:
A*1 ± B*2
Rear: C*3 ± D*455.3 ± 85.3 mm (2.18 ± 3.36 in.)
74.6 ± 104.6 mm (2.94 ± 4.12 in.)
UCK45L±GKBSKA Front:
A*1 ± B*2
Rear: C*3 ± D*445.5 ± 75.5 mm (1.79 ± 2.97 in.)
61.0 ± 91.0 mm (2.40 ± 3.58 in.)
UCK45L±GKBLKA Front:
A*1 ± B*2
Rear: C*3 ± D*446.8 ± 76.8 mm (1.84 ± 3.02 in.)
61.3 ± 91.3 mm (2.41 ± 3.59 in.)
A*1: Ground clearance of the front drive shaft center
B*
2: Ground clearance of the front adjusting cam bolt center
C*
3: Ground clearance of the rear axle shaft center
D*
4: Ground clearance of the rear lower control arm front bolt center

A21027
Wire Harness Side
Crankshaft Position Sensor C2
B17414
E6ECM Connector
NE± NE+
BR3795OK NGClearance
DI±214
± DIAGNOSTICSENGINE
408 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open and short in harness and connector between ECM and
crankshaft position sensor.
PREPARATION:
(a) Disconnect the C2 crankshaft position sensor connector.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
Crankshaft position sensor (C2±1) ±
NE+ (E6±21)Below 1 W
Crankshaft position sensor (C2±2) ±
NE± (E6±20)Below 1 W
Crankshaft position sensor (C2±1) or
NE+ (E6±21) ± Body ground10 kW or higher
Crankshaft position sensor (C2±2) or
NE± (E6±20) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
3 Check sensor installation (crankshaft position sensor).
CHECK:
Check the crankshaft position sensor installation.
OK:
The crankshaft position sensor is installed properly.
NG Tighten sensor installation bolt.
OK

B17414
E6
ECM Connector
VV2+
VV1±
VV1+VV2±
A21029
Wire Harness Side
VVT Sensor V16
V17
BR3795OK NGClearance
± DIAGNOSTICSENGINE
DI±219
413 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open and short in harness and connector between ECM and VVT sen-
sor.
PREPARATION:
(a) Disconnect the VVT sensor connector.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
VVT sensor (V16±1) ± VV1+ (E6±25)Below 1 W
VVT sensor (V16±2) ± VV1± (E6±24)Below 1 W
VVT sensor (V17±1) ± VV2+ (E6±18)Below 1 W
VVT sensor (V17±2) ± VV2± (E6±28)Below 1 W
VVT sensor (V16 ±1) or
VV1+ (E6±25) ± Body ground10 kW or higher
VVT sensor (V16±2) or
VV1± (E6±24) ± Body ground10 kW or higher
VVT sensor (V17 ±1) or
VV2+ (E6±18) ± Body ground10 kW or higher
VVT sensor (V17±2) or
VV2± (E6±28) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
3 Check sensor installation (VVT position sensor).
CHECK:
Check the VVT position sensor installation.
OK:
The VVT sensor is installed properly.
NG Tighten sensor installation bolt.
OK

BR3795OK NGClearance
B17411
SPD(+) E5
A23540
Wire Harness Side:
Front View
Combination Meter Connector C5
DI±282
± DIAGNOSTICSENGINE
476 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check sensor installation (Vehicle speed sensor).
CHECK:
Check the vehicle speed sensor installation.
OK:
The vehicle speed sensor is installed properly.
NG Tighten sensor installation bolt.
OK
5 Check for open and short in harness and connector between combination meter
and ECM.
PREPARATION:
(a) Disconnect the C5 combination meter connector.
(b) Disconnect the E5 ECM connector.
CHECK:
Check for resistance between the wire harness side connec-
tors.
OK:
Standard (Check for open):
Symbols (Terminal No.)Specified condition
SPD (E5±8) ± C5±25Below 1 W
Standard (Check for short):
Symbols (Terminal No.)Specified condition
SPD (E5±8) or C5±25 ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Check combination meter circuit (See page
DI±1632

B17414
E6ECM Connector
G2+
G2±
B17445
Wire Harness Side:
Camshaft Position Sensor C1
BR3795OK NGClearance
± DIAGNOSTICSENGINE
DI±307
501 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check for open and short in harness and connector between ECM and camshaft
position sensor.
PREPARATION:
(a) Disconnect the Camshaft position sensor connector.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between wire harness side connectors.
OK:
Standard:
Tester ConnectionSpecified Condition
Camshaft position sensor (C1±2) ±
G2+ (E6±19)Below 1 W
Camshaft position sensor (C1±1) ±
G2± (E6±29)Below 1 W
Camshaft position sensor (C1±2) or
G2+ (E6±19) ± Body ground10 kW or higher
Camshaft position sensor (C1±1) or
G2± (E6±29) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
4 Inspect sensor installation and signal plate tooth of LH camshaft timing pulley.
CHECK:
Check the camshaft position sensor installation.
OK:
The camshaft position sensor is installed properly.
NG Tighten sensor installation bolt.
OK

EM0580
A04087A04091A04236
Z00052
Z00054
44.5° EM±48
± ENGINE MECHANICALCYLINDER HEAD
2627 Author: Date:
2005 SEQUOIA (RM1146U)
9. CLEAN VALVES
(a) Using a gasket scraper, chip off any carbon from the valve
head.
(b) Using a wire brush, thoroughly clean the valve.
10. INSPECT VALVE STEMS AND GUIDE BUSHINGS
(a) Using a caliper gauge, measure the inside diameter of the
guide bushing.
Bushing inside diameter:
5.510 to 5.530 mm (0.2169 to 0.2177 in.)
(b) Using a micrometer, measure the diameter of the valve
stem.
Valve stem diameter:
Intake5.470 to 5.485 mm (0.2154 to 0.2159 in.)
Exhaust5.465 to 5.480 mm (0.2152 to 0.2157 in.)
(c) Subtract the valve stem diameter measurement from the
guide bushing inside diameter measurement.
Standard oil clearance:
Intake0.025 to 0.060 mm (0.0010 to 0.0024 in.)
Exhaust0.030 to 0.065 mm (0.0012 to 0.0026 in.)
Maximum oil clearance:
Intake0.08 mm (0.0031 in.)
Exhaust0.10 mm (0.0039 in.)
If the clearance is greater than maximum, replace the valve and
guide bushing. (See page EM±56)
11. INSPECT AND GRIND VALVES
(a) Grind the valve enough to remove pits and carbon.
(b) Check that the valve is ground to the correct valve face
angle.
Valve face angle: 44.5°

F01718F05219F14317
Front:
Rear:A
B
C
DSA23H±05
SA±4
± SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
3000 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT WHEEL ALIGNMENT
INSPECTION
NOTICE:
Be sure to perform the zero point calibration of the steering
angle, master cylinder pressure, yaw rate and deceleration
sensors (See page DI±897).
1. MEASURE VEHICLE HEIGHT
Measuring points:
A: Ground clearance of the front drive shaft center
B: Ground clearance of the front adjusting cam bolt center
C: Ground clearance of the rear axle shaft center
D: Ground clearance of the rear lower control arm front bolt cen-
ter
Vehicle height (Except air suspension models):
UCK35L±GKBSKA
Tire size: P245/70R16
Front
Rear
Tire size: P265/70R16 and P265/65R17
Front
Rear
A ± B: 69.7 mm (2.74 in.)
C ± D: 76.2 mm (3.00 in.)
A ± B: 69.5 mm (2.74 in.)
C ± D: 75.5 mm (2.97 in.)
UCK35L±GKBLKA
Front
Rear
A ± B: 71.6 mm (2.82 in.)
C ± D: 77.3 mm (3.04 in.)
UCK45L±GKBSKA
Front
Rear
A ± B: 61.6 mm (2.43 in.)
C ± D: 63.8 mm (2.51 in.)
UCK45L±GKBLKA
Front
Rear
A ± B: 62.8 mm (2.47 in.)
C ± D: 65.2 mm (2.57 in.)
Vehicle height (Air suspension models):
UCK35L±GKBSKA
Tire size: P245/70R16
Front
Rear
Tire size: P265/70R16 and P265/65R17
Front
Rear
A ± B: 68.5 mm (2.69 in.)
C ± D: 74.8 ± 104.8 mm (2.94 ± 4.13 in.)
A ± B: 68.3 mm (2.69 in.)
C ± D: 74.1 ± 104.1 mm (2.92 ± 4.10 in.)
UCK35L±GKBLKA
Front
Rear
A ± B: 70.3 mm (2.77 in.)
C ± D: 74.6 ± 104.6 mm (2.94 ± 4.12 in.)
UCK45L±GKBSKA
Front
Rear
A ± B: 60.5 mm (2.38 in.)
C ± D: 61.0 ± 91.0 mm (2.40 ± 3.58 in.)
UCK45L±GKBLKA
Front
Rear
A ± B: 61.8 mm (2.43 in.)
C ± D: 61.3 ± 91.3 mm (2.41 ± 3.59 in.)
NOTICE:
Before inspecting the wheel alignment, adjust the vehicle
height to the specified value.

05_SEQUOIA_U (L/O 0408)
ix
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
On±pavement and off±road
driving tips
This vehicle belongs to the utility vehicle class. Utility
vehicles have a significantly higher rollover rate than
other types of vehicles. This vehicle will handle and
maneuver differently from an ordinary passenger car be-
cause it is designed for off±road use also. In addition,
this vehicle has a higher ground clearance and center of
gravity than that of an ordinary passenger car. This
vehicle design feature causes this type of vehicle to be
more likely to rollover. Failure to operate this vehicle
correctly may result in loss of control, accidents or
vehicle rollover causing death or serious injury. Be sure
to read ªOff±road vehicle precautionsº on page 334 in
Section 2 and ªOff±road driving precautionsº on page
365 in Section 3.
Leak detection pump
This pump performs fuel evaporation leakage check. This
check is done approximately five hours after the engine is
turned off. So you may hear sound coming from under-
neath the luggage compartment for several minutes. It
does not indicate a malfunction.