Page 48 of 4323

MA001±42
± MAINTENANCEOUTSIDE VEHICLE
MA±1
48 Author: Date:
2005 SEQUOIA (RM1146U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing.
If necessary, tighten them.
4. TIRE ROTATION (See page SA±3)
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, find the cause and correct.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.
Page 3586 of 4323

BO45T±01
H16689
Back Door Side Garnish
Back Door Center Garnishw/o Rear spoiler:
High Mount Stop Light
Outside MouldingBack Door Hingew/ Rear spoiler:
Rear Spoiler
Back Door Hinge
Rear Wiper Arm
Wiper
Motor
Grommet
Rear Wiper
Motor
Service Hole Plug
Outside MouldingStep Liner Back Door Glass Back Door Side
Garnish
Back Door Glass Run
Outer Weatherstrip
Back Door
Glass Guide Rail
Outer Cover
Power Window Regulator
Back Door
Glass Guide RailOutside Handle
Key Cylinder
Rear Light
Lower Stopper Rear Light Opening Hole Cover
Stopper Cushion
Back Door Lock ProtectorControl
Cable
Stopper Cushion
: Specified torque Strap Cover
Back Door Pull StrapBack Door Trim Board Inner WeatherstripNo. 1 Service
Hole Cover
Opening Hole Cover
19.5 (199, 14.4)
8.0 (82, 71 in.´lbf)
5.5 (56, 49 in.´lbf)
5.5 (56, 49 in.´lbf)
8.0 (82, 71 in.´lbf)
N´m (kgf´cm, ft´lbf)No. 2 Service
Hole Cover
Back Door
Handle
Protector
Licence Plate
Light
Assembly
Outside
Garnish
Washer Nozzle
Lower Stopper
Power Window
Regulator Motor
Back Door Lock
19.5 (199, 14.4)
8.0 (82, 71 in.´lbf)
± BODYBACK DOOR
BO±25
3578 Author: Date:
2005 SEQUOIA (RM1146U)
BACK DOOR
COMPONENTS
Page 3607 of 4323
BO468±03
H24888
Quarter Opening
Retainer
Rear Door Outside Moulding
Sub±Assembly
Front Fender MouldingRear Bumper
Protector
Rear Bumper
Extension
Rear Bumper Seal
Quarter Outside
Moulding
Rear Mudguard
Rear Door Outside Moulding
Front Door Outside Moulding
Front Mudguard
: Specified torque
N´m (kgf´cm, ft´lbf)
5.0 (50, 43 in.´lbf)
Non±reusable part
Rivet BO±46
± BODYBODY OUTSIDE MOULDING
3599 Author: Date:
2005 SEQUOIA (RM1146U)
BODY OUTSIDE MOULDING
COMPONENTS
Page 3609 of 4323
H16702
H16703
BO±48
± BODYBODY OUTSIDE MOULDING
3601 Author: Date:
2005 SEQUOIA (RM1146U)
4. REMOVE REAR DOOR OUTSIDE MOULDING SUB±
ASSEMBLY
(a) Remove the 3 screws.
(b) Using a moulding remover, remove the rear door outside
moulding sub±assembly.
HINT:
Tape the moulding remover tip before use.
(c) Remove the 3 screws and quarter opening retainer.
5. REMOVE QUARTER OUTSIDE MOULDING
(a) Remove the 3 screws.
(b) Using a moulding remover, remove the quarter outside
moulding.
HINT:
Tape the moulding remover tip before use.
6. REMOVE REAR BUMPER EXTENSION
(a) Remove the 4 screws and rear mudguard.
(b) Remove the rear bumper cover.
(c) Remove the 4 nuts and rear bumper extension.
Page 3610 of 4323

BO46A±02
H16701
Adhesive
Tape
± BODYBODY OUTSIDE MOULDING
BO±49
3602 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. INSTALL REAR BUMPER EXTENSION
(a) Install the rear bumper extension with the 4 nuts.
Torque: 5.0 N´m (50 kgf´cm, 43 in.´lbf)
(b) Install the rear bumper cover.
(c) Install the rear mudguard with the 4 screws.
2. INSTALL QUARTER OUTSIDE MOULDING
Install the quarter outside moulding with the 3 screws.
3. INSTALL REAR DOOR OUTSIDE MOULDING SUB±
ASSEMBLY
(a) Install the quarter opening retainer with the 3 screws.
(b) Install the rear door outside moulding sub±assembly with
the 3 screws.
4. INSTALL REAR DOOR OUTSIDE MOULDING
(a) Clean the rear door mounting surface.
(1) Using a heat light, heat the rear door mounting sur-
face to 40 ± 60 °C (104 ± 140 °F)
(2) Remove the adhesive tape from the rear door.
(3) Wipe off the stain with cleaner.
(b) If reusing the moulding:
Clean the rear door outside moulding.
(1) Using a heat light, heat the moulding to 20 ± 30 °C
(68 ± 86 °F)
NOTICE:
Do not heat the moulding excessively.
(2) Remove the adhesive tape from the moulding.
(3) Wipe off the stains with cleaner.
(4) Apply new adhesive tapes to the moulding.
(c) Install the rear door outside moulding.
(1) Using a heat light, heat the rear door panel and
moulding
Rear door panel: 40 ± 60 °C (104 ± 140 °F)
Moulding: 20 ± 30 °C (68 ± 86 °F)
NOTICE:
Do not heat the rear door and moulding.
(2) Lift the moulding release sheet from face of mould-
ing.
NOTICE:
When the moulding release sheet is removed, make sure
that no dirt or dust can get onto the uncoated area.
(3) Align the boss with the corresponding hole in rear
door, and press firmly on the moulding.
5. INSTALL FRONT DOOR OUTSIDE MOULDING
(a) Clean the front door mounting surface.
(1) Using a heat light, heat the front door mounting sur-
face to 40 ± 60 °C (104 ± 140 °F)
(2) Remove the adhesive tape from the front door.
(3) Wipe off the stain with cleaner.
Page 3621 of 4323
BO46I±02
H18890
Roof Console BoxFront Door Opening
Trim WeatherstripRoof Headlining
Assist Grip
Assist Grip Plug Front Pillar Garnish
Sun Visor
Roof Console BoxAssist Grip
Front Pillar
Garnish Sun Visor
Holder Holder
Inner Rear
View Mirror
No. 2 Stopper
Windshield Outside
Upper Moulding
Windshield Outside Moulding
Roof Side Rail
Weatherstrip Windshield
Outside Moulding
Windshield Glass
Wiper Arm
Wiper Arm
Cowl Top Ventilator Louver
Hood to Cowl Top Seal
Non±reusable part
N´m (kgf´cm, ft´lbf): Specified torque No. 2 Stopper
Dam w/ Sliding roof:
Roof Side Rail
Weatherstrip
w/ Electro chrmic
inner rear view mirror:
Mirror Cover
Inner Rear
View Mirror
2.5 (25, 22 in.´lbf)
Front Door
Opening Trim
Weatherstrip
w/ Double sun visor:
Sun Visor
2.5 (25, 22 in.´lbf)
Dam
Assist Grip Plug
Holder
Holder
Siding Roof
Headlining
Trim
20 (204, 15)
BO±60
± BODYWINDSHIELD
3613 Author: Date:
2005 SEQUOIA (RM1146U)
WINDSHIELD
COMPONENTS
Page 3622 of 4323

BO4HJ±01
H16717
Clip
H167342 Clips
H167354 Clips
H18891
± BODYWINDSHIELD
BO±61
3614 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE FRONT DOOR OPENING TRIM WEATH-
ERSTRIPS
2. REMOVE FRONT PILLAR GARNISH
(a) Remove the assist grip.
(1) Using a screwdriver, remove the 2 assist grip plugs.
HINT:
Tape the screwdriver tip before use.
(2) Remove the 2 screws and assist grip.
(b) Remove the front pillar garnish.
(c) Use the same manner described above to the other side.
3. REMOVE SUN VISORS AND HOLDERS
4. w/ Sliding roof:
REMOVE ROOF CONSOLE BOX
(a) Remove the 2 screws.
(b) Using a screwdriver, remove the roof console box.
HINT:
Tape the screwdriver tip before use.
(c) Disconnect the connectors.
5. w/o Sliding roof:
REMOVE ROOF CONSOLE BOX
(a) Remove the 4 screws.
(b) Using a screwdriver, remove the roof console box.
HINT:
Tape the screwdriver tip before use.
(c) Disconnect the connectors.
6. w/o Electro chromic inner rear view mirror:
REMOVE INNER REAR VIEW MIRROR
Remove the torx screw and inner rear view mirror as shown in
the illustration.
Page 3628 of 4323
H18893
H18894
± BODYWINDSHIELD
BO±67
3620 Author: Date:
2005 SEQUOIA (RM1146U)
(d) Torque the 2 nuts.
Torque: 20 N´m (204 kgf´cm, 15 ft´lbf)
(e) Install the 2 cap.
17. w/ Electro chromic inner rear view mirror:
INSTALL INNER REAR VIEW MIRROR
(a) Install the inner rear view mirror and torx screw.
Torque: 2.5 N´m (25 kgf´cm, 22 in.´lbf)
(b) Connect the connector.
(c) Install the mirror cover.
18. w/o Electro chromic inner rear view mirror:
INSTALL INNER REAR VIEW MIRROR
Instll the inner rear view mirror and torx screw.
Torque: 2.5 N´m (25 kgf´cm, 22 in.´lbf)
19. INSTALL ROOF CONSOLE BOX
20. INSTALL SUN VISORS AND HOLDERS
21. INSTALL FRONT PILLAR GARNISHES
22. INSTALL FRONT DOOR OPENING TRIM WEATH-
ERSTRIPS