Page 48 of 4323

MA001±42
± MAINTENANCEOUTSIDE VEHICLE
MA±1
48 Author: Date:
2005 SEQUOIA (RM1146U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing.
If necessary, tighten them.
4. TIRE ROTATION (See page SA±3)
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, find the cause and correct.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.
Page 78 of 4323
PP1AV±03
PP±20
± PREPARATIONLUBRICATION
78 Author: Date:
2005 SEQUOIA (RM1146U)
EQUIPMENT
Oil pressure gauge
Precision straight edge
Torque wrench
Page 80 of 4323
PP1AX±03
PP±22
± PREPARATIONLUBRICATION
80 Author: Date:
2005 SEQUOIA (RM1146U)
SSM (Special Service Materials)
08826±00080Seal Packing Black or equivalent
(FIPG)Oil pump
No.1 oil pan
No.2 oil pan
08833±00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentOil pressure switch
Page 90 of 4323
PP42K±01
PP±32
± PREPARATIONAUTOMATIC TRANSMISSION (A750E, A750F)
90 Author: Date:
2005 SEQUOIA (RM1146U)
AUTOMATIC TRANSMISSION (A750E, A750F)
SST (Special Service Tools)
09350±30020TOYOTA Automatic Transmission
Tool Set
(09351±32020)Stator StopperTorpue converter clutch and drive
plate
09992±00095Automatic Transmission Oil
Pressure Gauge Set
(09992±00231)Adaptor C
(09992±00271)Gauge Assy
09308±10010Oil Seal PullerExtension housing oil seal
09325±40010Transmission Oil PlugExtension housing oil seal
09023±12701Union Nut Wrench 17mmOil cooler pipe
Page 119 of 4323
± PREPARATIONSTEERING
PP±61
11 9 Author: Date:
2005 SEQUOIA (RM1146U)
09631±20051Steering Rack Cover ºCºPS gear
09631±20081Seal Ring ToolPS gear
09640±10010Power Steering Pressure Gauge
Set
(09641±01010)Gauge AssyPower steering fluid
(09641±01030)Attachment BPower steering fluid
(09641±01060)Attachment EPower steering fluid
09816±30010Oil Pressure Switch SocketPS gear
09910±00015Puller Set
(09911±00011)Puller ClampSteering column
(09912±00010)Puller Slide HammerSteering column
09922±10010Variable Open WrenchPS gear
09950±50013Puller C Set
(09951±05010)Hanger 150Steering column
Page 154 of 4323

SS0CB±23
SS±12
± SERVICE SPECIFICATIONSSFI
154 Author: Date:
2005 SEQUOIA (RM1146U)
SFI
SERVICE DATA
Fuel pumpResistance at 20°C (68°F)0.2 to 3.0 W
Fuel pressure
regulatorFuel pressure at no vacuum265 to 304 kPa
(2.7 to 3.1 kgf/cm2, 38 to 44 psi)
InjectorResistance at 20°C (68°F)
Injection volume
Difference between each cylinder
Fuel leakage13.4 to 14.2 W
56 to 69 cm3 (3.4 to 4.2 cu in.) per 15 seconds
13 cm3 (0.8 cu in.) or less
1 drop or less per 12 minutes
MAF meterResistance (THA ± E2) at ±20°C (±4°F)
at 20°C (68°F)
at 60°C (140°F)12.5 to 16.9 kW
2.19 to 2.67 kW
0.50 to 0.68 kW
Throttle bodyThrottle body fully closed angle5.5°
Throttle control
motorMotor resistance at 20°C (68°F)0.3 to 100 W
VSV for EVAPResistance at 20°C (68°F)30 to 34 W
VSV for ACISResistance at 20°C (68°F)33 to 39 W
VT sensorResistance Cold
Hot835 to 1,400 W
1,060 to 1,645 W
Knock sensorResistance at 20°C (68°F)120 to 280 W
ECT sensorResistance at ±20°C (±4°F)
0°C (32°F)
20°C (68°F)
40°C (104°F)
60°C (140°F)
80°C (176°F)10 to 20 kW
4 to 7 kW
2 to 3 kW
0.9 to 1.3 kW
0.4 to 0.7 kW
0.2 to 0.4 kW
Air±fuel ratio
sensorHeater coil resistance at 20°C (68°F)11 to 16 kW
Heated oxygen
sensorHeater coil resistance at 20°C (68°F)11 to 16 kW
Accelerator pedal
position sensorStandard throttle valve opening percentage
Sensor lever full±open position
60 % or more
Fuel cut rpmFuel return rpm1,400 rpm
Fuel pump resisterat 20°C (68 °F)0.70 to 0.76 kW
Page 155 of 4323
SS0CC±22
± SERVICE SPECIFICATIONSSFI
SS±13
155 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Fuel pressure pulsation damper x Delivery pipe for use with SST33
39340
40024
29
Fuel pressure regulator x RH delivery pipe7.58066 in.´lbf
Front fuel pipe x Lower intake manifold7.58066 in.´lbf
Fuel return pipe x Delivery pipe7.58066 in.´lbf
Delivery pipe x Intake manifold2121415
Fuel tank band x Body6263245
Fuel pressure regulator x Delivery pipe7.57666 in.´lbf
Throttle body x Intake manifold1818513
ECT sensor x Front water bypass joint19.620014
Knock sensor x Cylinder head2020415
Air±fuel ratio sensor x Exhaust manifold4445032
Heated oxygen sensor x Front exhaust pipe4445032
Fuel pump resister x Body88271 in.´lbf
Camshaft oil control valve x Cylinder head7.58066 in.´lbf
Air pump assembly x Cylinder head1616312
Page 158 of 4323
SS0OB±05
SS±16
± SERVICE SPECIFICATIONSLUBRICATION
158 Author: Date:
2005 SEQUOIA (RM1146U)
LUBRICATION
SERVICE DATA
Oil pressureat idle speed
at 3,000 rpm29 kPa (0.3 kgf/cm2, 4.3 psi) or more
294 to 588 kPa (3.0 to 6.0 kgf/cm2, 43 to 85 psi)
Oil pumpTip clearance Standard
Maximum
Side clearance Standard
Maximum
Body clearance Standard
Maximum0.060 to 0.180 mm (0.0024 to 0.0071 in.)
0.18 mm (0.0071 in.)
0.030 to 0.090 mm (0.0012 to 0.0035 in.)
0.09 mm (0.0035 in.)
0.250 to 0.325 mm (0.0098 to 0.0128 in.)
0.325 mm (0.0128 in.)