Page 3609 of 4323
H16702
H16703
BO±48
± BODYBODY OUTSIDE MOULDING
3601 Author: Date:
2005 SEQUOIA (RM1146U)
4. REMOVE REAR DOOR OUTSIDE MOULDING SUB±
ASSEMBLY
(a) Remove the 3 screws.
(b) Using a moulding remover, remove the rear door outside
moulding sub±assembly.
HINT:
Tape the moulding remover tip before use.
(c) Remove the 3 screws and quarter opening retainer.
5. REMOVE QUARTER OUTSIDE MOULDING
(a) Remove the 3 screws.
(b) Using a moulding remover, remove the quarter outside
moulding.
HINT:
Tape the moulding remover tip before use.
6. REMOVE REAR BUMPER EXTENSION
(a) Remove the 4 screws and rear mudguard.
(b) Remove the rear bumper cover.
(c) Remove the 4 nuts and rear bumper extension.
Page 3610 of 4323

BO46A±02
H16701
Adhesive
Tape
± BODYBODY OUTSIDE MOULDING
BO±49
3602 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. INSTALL REAR BUMPER EXTENSION
(a) Install the rear bumper extension with the 4 nuts.
Torque: 5.0 N´m (50 kgf´cm, 43 in.´lbf)
(b) Install the rear bumper cover.
(c) Install the rear mudguard with the 4 screws.
2. INSTALL QUARTER OUTSIDE MOULDING
Install the quarter outside moulding with the 3 screws.
3. INSTALL REAR DOOR OUTSIDE MOULDING SUB±
ASSEMBLY
(a) Install the quarter opening retainer with the 3 screws.
(b) Install the rear door outside moulding sub±assembly with
the 3 screws.
4. INSTALL REAR DOOR OUTSIDE MOULDING
(a) Clean the rear door mounting surface.
(1) Using a heat light, heat the rear door mounting sur-
face to 40 ± 60 °C (104 ± 140 °F)
(2) Remove the adhesive tape from the rear door.
(3) Wipe off the stain with cleaner.
(b) If reusing the moulding:
Clean the rear door outside moulding.
(1) Using a heat light, heat the moulding to 20 ± 30 °C
(68 ± 86 °F)
NOTICE:
Do not heat the moulding excessively.
(2) Remove the adhesive tape from the moulding.
(3) Wipe off the stains with cleaner.
(4) Apply new adhesive tapes to the moulding.
(c) Install the rear door outside moulding.
(1) Using a heat light, heat the rear door panel and
moulding
Rear door panel: 40 ± 60 °C (104 ± 140 °F)
Moulding: 20 ± 30 °C (68 ± 86 °F)
NOTICE:
Do not heat the rear door and moulding.
(2) Lift the moulding release sheet from face of mould-
ing.
NOTICE:
When the moulding release sheet is removed, make sure
that no dirt or dust can get onto the uncoated area.
(3) Align the boss with the corresponding hole in rear
door, and press firmly on the moulding.
5. INSTALL FRONT DOOR OUTSIDE MOULDING
(a) Clean the front door mounting surface.
(1) Using a heat light, heat the front door mounting sur-
face to 40 ± 60 °C (104 ± 140 °F)
(2) Remove the adhesive tape from the front door.
(3) Wipe off the stain with cleaner.
Page 3611 of 4323

H16700
Adhesive
Tape
BO±50
± BODYBODY OUTSIDE MOULDING
3603 Author: Date:
2005 SEQUOIA (RM1146U)
(b) If reusing the moulding:
Clean the front door outside moulding.
(1) Using a heat light, heat the mounting to 20 ± 30 °C
(68 ± 86 °F)
NOTICE:
Do not heat the moulding excessively.
(2) Remove the adhesive tape from the moulding.
(3) Wipe off the stains with cleaner.
(4) Apply new adhesive tapes to the moulding.
(c) Install the front door outside moulding.
(1) Using a heat light, heat the front door panel and
moulding
Front door panel: 40 ± 60 °C (104 ± 140 °F)
Moulding: 20 ± 30 °C (68 ± 86 °F)
NOTICE:
Do not heat the front door and moulding.
(2) Lift the moulding release sheet from face of mould-
ing.
NOTICE:
When the moulding release sheet is removed, make sure
that no dirt or dust can get onto the uncoated area.
(3) Align the boss with the corresponding hole in front
door, and press firmly on the moulding.
6. INSTALL FRONT FENDER MOULDING
(a) Install the front fender moulding with the 5 screws.
(b) Install the front mudguard with the 3 screws.
Page 3612 of 4323
BO46B±03
H24862
Rear Fender Wheel
Opening Moulding
Rear Mudguard
Non±reusable Part
± BODYWHEEL ARCH MOULDING
BO±51
3604 Author: Date:
2005 SEQUOIA (RM1146U)
WHEEL ARCH MOULDING
COMPONENTS
Page 3613 of 4323
BO46C±01
H16710
Roof Drip Side Mouldingw/ Roof rack:
Front Leg CoverRear Leg Cover
Rear Leg Cover
Roof Rack Front Leg Cover
11 (115, 8)
11 (115, 8)
11 (115, 8)
11 (115, 8)
: Specified torqueN´m (kgf´cm, ft´lbf) BO±52
± BODYROOF DRIP SIDE MOULDING
3605 Author: Date:
2005 SEQUOIA (RM1146U)
ROOF DRIP SIDE MOULDING
COMPONENTS
Page 3614 of 4323
BO46D±01
N18625
N18626
± BODYROOF DRIP SIDE MOULDING
BO±53
3606 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. w/ Roof rack:
REMOVE ROOF RACK (See page BO±173)
2. REMOVE ENDS OF ROOF DRIP SIDE MOULDING
(a) Apply protective tape to the outer surface to keep the sur-
face from being scratched.
(b) Using a heat light, heat the moulding to 20 ± 30 °C (68 ±
86 °F)
NOTICE:
Do not heat the moulding excessively.
(c) Using a scraper, pull off the roof drip side moulding from
the front and rear ends.
HINT:
Tape the scraper tip before use.
3. REMOVE ROOF DRIP SIDE MOULDING
(a) Pull off the moulding by cutting the adhesive with a knife
at the front and rear ends.
(b) Remove the moulding.
NOTICE:
Do not damage the body with the knife.
Page 3615 of 4323

BO46E±01
H16712
Adhesive Tape
Adhesive Tape
BO±54
± BODYROOF DRIP SIDE MOULDING
3607 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. CLEAN CONTACT SURFACE OF BODY
(a) Using a heat light, heat the moulding surface to 40 ± 60
°C (104 ± 140°F).
NOTICE:
Do not heat the body excessively.
(b) Using a knife, cut away any rough areas on the body.
NOTICE:
Be careful not to damage the body.
(c) Wipe off stains with cleaner.
2. If reusing the moulding:
CLEAN MOULDING
(a) Using a heat light, heat the moulding surface to 20 ± 30
°C (68 ± 86°F).
NOTICE:
Do not heat the moulding excessively.
(b) Using a knife, cut the remaining adhesive from the mould-
ing.
NOTICE:
Be careful not to damage the moulding.
(c) Wipe off stains with cleaner.
(d) Apply a new adhesive tape to the moulding as shown in
the illustration.
3. COAT CONTACT SURFACE OF BODY WITH PRIMER
ºMº
Using a brush, coat the contact surface on the body with Primer
M as shown in the illustration.
NOTICE:
Allow 3 minutes or more to dry the primer coated sur-
face.
Do not coat the adhesive.
Page 3616 of 4323
H16711
Windshield Glass
Primer M
Apply Primer M on
panel in this rangeApply Primer M on
panel in this rangePrimer M
H16713
Windshield GlassAdhesive
20 mm
(0.79 in.)
6 mm (0.24 in.)Adhesive
20 mm
(0.79 in.)
± BODYROOF DRIP SIDE MOULDING
BO±55
3608 Author: Date:
2005 SEQUOIA (RM1146U)
Do not keep any of the opened Primer M for later use.
4. APPLY ADHESIVE
(a) Cut off the tip of cartridge nozzle.
Part No. 08850±00801 or equivalent.
HINT:
After cutting off the tip, use all adhesive within the time de-
scribed in the table below.
TemperatureTackfree time
35 °C (95 °F)15 minutes
20 °C (68 °F)100 minutes
5 °C (41 °F)8 minutes
(b) Load the cartridge into the sealer gun.
(c) Apply adhesive to the hatched area in the illustration for
both front and rear of the vehicle.
5. INSTALL ROOF DRIP SIDE MOULDING
(a) Using a heat light, heat the moulding to 20 ± 30 °C (68 ±
86 °F)
NOTICE:
Do not heat the moulding excessively.