Page 3153 of 4323
SA17E±04
F14301
Stabilizer Bar
Bushing Bracket
N´m (kgf´cm, ft´lbf) : Specified torqueStabilizer Bar Link
37 (377, 27)37 (377, 27)
Bushing Bracket
Stabilizer Bar Link
69 (704, 51)
69 (704, 51)
69 (704, 51)
69 (704, 51)
± SUSPENSION AND AXLEREAR STABILIZER BAR
SA±149
3145 Author: Date:
2005 SEQUOIA (RM1146U)
REAR STABILIZER BAR
COMPONENTS
Page 3154 of 4323
SA17F±04
F14302
F14303
SA±150
± SUSPENSION AND AXLEREAR STABILIZER BAR
3146 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE REAR WHEELS
Torque: 110 N´m (1,150 kgf´cm, 83 ft´lbf)
2. SUPPORT REAR AXLE HOUSING WITH JACK
3. REMOVE STABILIZER BAR LINKS
(a) Remove the 2 nuts and stabilizer bar link.
Torque: 69 N´m (704 kgf´cm, 51 ft´lbf)
HINT:
If the ball joint stud turns together with the nut, use a hexagon
wrench to hold the stud.
(b) Use the same procedure described above to the other
side.
4. REMOVE STABILIZER BAR FROM REAR AXLE
HOUSING
(a) Remove the 4 bolts and stabilizer bar with the bushings
and brackets.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
(b) Remove the 2 brackets and 2 bushings from the stabilizer
bar.
Page 3155 of 4323
SA24K±02
F14304
± SUSPENSION AND AXLEREAR STABILIZER BAR
SA±151
3147 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
INSPECT STABILIZER BAR LINK
Rotate the ball joint stud in all directions.
If it does not move smoothly and freely, replace the stabilizer
link.
Page 3156 of 4323
SA17G±03
SA±152
± SUSPENSION AND AXLEREAR STABILIZER BAR
3148 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±150).
Page 3157 of 4323

SA2CZ±01
F16823
F14100
ºAº
Air tube
Housing
Connector No. 1
F14101
SST
Air tube
F14102
Plate
O±ringConnector No.2
SST
Air tube
± SUSPENSION AND AXLEELECTRONIC MODULATED AIR SUSPENSION
SA±153
3149 Author: Date:
2005 SEQUOIA (RM1146U)
ELECTRONIC MODULATED AIR SUSPENSION
PRECAUTION
1. WHEN LIFTING UP VEHICLE
(a) When jacking up or lifting up, stop operation of the air sus-
pension control system by pressing the height control
mode select switch.
2. DISCONNECTION AND CONNECTION OF HEIGHT
CONTROL TUBE
NOTICE:
Disconnection and connection of the height control
tube should be performed by hand to prevent foreign
objects from entering.
Never damage the height control tube.
(a) Disconnect the height control tube.
(1) Pinch ºAº of the connector No. 1 and pull out from
the housing.
(2) Set the SST to the tube.
SST 09730±00010
(3) Insert SST into the housing to expand the claw of
the connector No.2 in the housing.
(4) Pull out the tube with SST inserted.
NOTICE:
Do not pull on the tube with excessive force.
Page 3158 of 4323

F19817
O±ring
Plate
F19818
CardboardO±ring
Plate
F19819
Connector No.2
F14103
HousingClaw
Connector No. 1
Air tube
Port (Hole)
SA±154
± SUSPENSION AND AXLEELECTRONIC MODULATED AIR SUSPENSION
3150 Author: Date:
2005 SEQUOIA (RM1146U)
(5) Insert a screwdriver into the circular hole on the
housing, and remove the connector No.2, the 2 O±
rings and the plate from the housing.
HINT:
The O±rings, plate and connector No.2 are non±reusable parts.
(b) Install 2 O±rings and the plate.
(1) Apply MP grease to 2 new O±rings and plate and
install them to the straight tube or an equivalent.
NOTICE:
Install the plate between the O±rings.
Keep foreign matter from adhering to the O±rings and the
height control tube in order to prevent air leaks.
(2) Insert the tube on which the 2 O±rings and plate are
installed into the housing, and then push it in lightly
with a piece of rolled up cardboard.
(3) Push the connector No.2 into the housing to where
a clicking sound is heard.
(c) Install the height control tube.
(1) Push the tube and connector No.1 into the housing
to where a clicking sound is heard.
NOTICE:
The port (hole) of the housing should be set in the
position 90° from the claws of connector No. 1.
Pull the tube lightly to make sure that it is securely
connected.
Page 3159 of 4323
± SUSPENSION AND AXLEELECTRONIC MODULATED AIR SUSPENSION
SA±155
3151 Author: Date:
2005 SEQUOIA (RM1146U)
Prevent foreign matter from being attached to the O±
rings and height control tube. Failure to do so may
cause air leakage.
Page 3160 of 4323

SA2D0±01
F16824
HIGH
NORMAL
LOW SA±156
± SUSPENSION AND AXLEELECTRONIC MODULATED AIR SUSPENSION
3152 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
1. ADJUST STANDARD VEHICLE HEIGHT
(a) Release the parking brake and stabilize the suspensions by pushing up and down on the corners of
the vehicle.
(b) Place the shift lever into the ºNº position and settle the tires by moving the vehicle back and forth.
(c) Start the engine.
(d) On the height control switch, first press ºHIGHº to raise the vehicle height, and then change the switch
to ºLOWº to lower it. Perform this operation one more time.
NOTICE:
Make sure to release the parking brake and move the shift lever into the ºNº position.
2. INSPECT TIRE (See page SA±3)
3. MEASURE VEHICLE HEIGHT (See page SA±4)
4. OPERATE HEIGHT CONTROL SWITCH AND CHECK
VEHICLE HEIGHT CHANGE
(a) Start the engine and change the height control switch
from the NORMAL position to the HIGH and LOW posi-
tions.
Check the time until the height adjustment is completed
and the amount of change in vehicle height.
Adjustment time
From operation of height control switch
to start of compressor.Approx. 2 sec.
From start of compressor to completion
of height adjustment.Approx. 20 sec.
Amount of change in vehicle height
HIGH position: 40 mm (1.57 in.)
LOW position:
4WD models: ±30 mm (±1.18 in.)
2WD models: ±15 mm (±0.59 in.)