2001 TOYOTA SEQUOIA wheel size

± INTRODUCTIONTERMS
IN±43
43 Author: Date:
2005 SEQUOIA (RM1146U) OEM
Original Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead Valve
OPTOption
ORVROn±board Refilling Vapor Recovery
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take±Off
P/WPower Window
R & PRack And Pinion
RAMRandom Access Memory
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight±Hand
RHDRight±Hand Drive
RLYRelay
ROMRead Only Memory
RRRear
RRSRigid Front Suspension
RWDRear±Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold±Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection
TCTurbocharger
TCCSTOYOTA Computer±Controlled System
TCVTiming Control Valve
TDCTop Dead Center
TEMP.Temperature
TEMSTOYOTA Electronic Modulated Suspension
TFTTOYOTA Free±Tronic
TISTotal Information System For Vehicle Development

IN±44
± INTRODUCTIONTERMS
44 Author: Date:
2005 SEQUOIA (RM1146U) T/M
Transmission
TMCTOYOTA Motor Corporation
TMMKTOYOTA Motor Manufacturing Kentucky, Inc.
TRCTraction Control System
TURBOTurbocharge
TWCThree±Way Catalyst
U/DUnderdrive
U/SUndersize
VCVVacuum Control Valve
VENTVentilator
VIMVehicle Interface Module
VINVehicle Identification Number
VPSVariable Power Steering
VSCVehicle Skid Control
VSVVacuum Switching Valve
VTVVacuum Transmitting Valve
VVT±iVariable Valve Timing±intelligent
W/With
WGNWagon
W/HWire Harness
W/OWithout
1STFirst
2NDSecond
2WDTwo Wheel Drive Vehicle (4 x 2)
3RDThird
4THFourth
4WDFour Wheel Drive Vehicle (4 x 4)
4WSFour Wheel Steering System
5THFifth

SS0OJ±22
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS±31
173 Author: Date:
2005 SEQUOIA (RM1146U)
SUSPENSION AND AXLE
SERVICE DATA
Tire size: P245/70R16 Front
Rear220 kPa (2.2 kgf/cm2, 32 psi)
240 kPa (2.4 kgf/cm2, 35 psi)
Cold tire inflation
pressureTire size: P265/70R16 Front
Rear220 kPa (2.2 kgf/cm2, 32 psi)
220 kPa (2.2 kgf/cm2, 32 psi)ressure
Tire size: P265/65R17 Front
Rear220 kPa (2.2 kgf/cm2, 32 psi)
220 kPa (2.2 kgf/cm2, 32 psi)
Vehicle height (Except air suspension models)
UCK35L±GKBSKA
Tire size: P245/70R16 Front:
A*1 ± B*2
Rear: C*3 ± D*4
Tire size: P265/70R16 and P265/65R17
Front:
A*1 ± B*2
Rear: C*3 ± D*4
69.7 mm (2.74 in.)
76.2 mm (3.00 in.)
69.5 mm (2.74 in.)
75.5 mm (2.97 in.)
UCK35L±GKBLKA Front:
A*1 ± B*2
Rear: C*3 ± D*471.6 mm (2.82 in.)
77.3 mm (3.04 in.)
UCK45L±GKBSKA Front:
A*1 ± B*2
Rear: C*3 ± D*461.6 mm (2.43 in.)
63.8 mm (2.51 in.)
Front wheel
UCK45L±GKBLKA Front:
A*1 ± B*2
Rear: C*3 ± D*462.8 mm (2.47 in.)
65.2 mm (2.57 in.)
Front wheel
Alignment
Vehicle height (Except air suspension models)g
UCK35L±GKBSKA
Tire size: P245/70R16 Front:
A*1 ± B*2
Rear: C*3 ± D*4
Tire size: P265/70R16 and P265/65R17
Front:
A*1 ± B*2
Rear: C*3 ± D*4
53.5 ± 83.5 mm (2.11 ± 3.29 in.)
74.8 ± 104.8 mm (2.94 ± 4.13 in.)
53.3 ± 83.3 mm (2.10 ± 3.28 in.)
74.1 ± 104.1 mm (2.92 ± 4.10 in.)
UCK35L±GKBLKA Front:
A*1 ± B*2
Rear: C*3 ± D*455.3 ± 85.3 mm (2.18 ± 3.36 in.)
74.6 ± 104.6 mm (2.94 ± 4.12 in.)
UCK45L±GKBSKA Front:
A*1 ± B*2
Rear: C*3 ± D*445.5 ± 75.5 mm (1.79 ± 2.97 in.)
61.0 ± 91.0 mm (2.40 ± 3.58 in.)
UCK45L±GKBLKA Front:
A*1 ± B*2
Rear: C*3 ± D*446.8 ± 76.8 mm (1.84 ± 3.02 in.)
61.3 ± 91.3 mm (2.41 ± 3.59 in.)
A*1: Ground clearance of the front drive shaft center
B*
2: Ground clearance of the front adjusting cam bolt center
C*
3: Ground clearance of the rear axle shaft center
D*
4: Ground clearance of the rear lower control arm front bolt center

SS±32
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
174 Author: Date:
2005 SEQUOIA (RM1146U)
CamberRight±left error: 30' (0.5°) or less
UCK35L±GKBSKA0°08' ± 45' (0.14° ± 0.75°)
UCK35L±GKBLKA0°06' ± 45' (0.10° ± 0.75°)
UCK45L±GKBSKA0°17' ± 45' (0.28° ± 0.75°)
UCK45L±GKBLKA0°16' ± 45' (0.26° ± 0.75°)
Caster (Except air suspension models) Right±left error: 30' (0.5°) or less
UCK35L±GKBSKA
Tire size: P245/70R16
Tire size: P265/70R16 and P265/65R17
2°56' ± 45' (2.93° ± 0.75°)
2°59' ± 45' (2.98° ± 0.75°)
UCK35L±GKBLKA3°02' ± 45' (3.04° ± 0.75°)
UCK45L±GKBSKA2°36' ± 45' (2.60° ± 0.75°)
UCK45L±GKBLKA2°38' ± 45' (2.64° ± 0.75°)
Caster (Air suspension models) Right±left error: 30' (0.5°) or less
UCK35L±GKBSKA
Tire size: P245/70R16
Tire size: P265/70R16 and P265/65R17
3°17' ± 45' (3.28° ± 0.75°)
3°20' ± 45' (3.33° ± 0.75°)
UCK35L±GKBLKA3°21' ± 45' (3.35° ± 0.75°)
UCK45L±GKBSKA2°55' ± 45' (2.91° ± 0.75°)
UCK45L±GKBLKA2°56' ± 45' (2.93° ± 0.75°)
Steering axis inclination Right±left error: 30' (0.5°) or less
Front wheel
AlignmentUCK35L±GKBSKA10°14' ± 45' (10.24° ± 0.75°)AlignmentUCK35L±GKBLKA10°16' ± 45' (10.27° ± 0.75°)
UCK45L±GKBSKA10°05' ± 45' (10.09° ± 0.75°)
UCK45L±GKBLKA10°07' ± 45' (10.11° ± 0.75°)
Toe±in (total) Rack end length difference: 1.5 mm (0.059 in.) or less
UCK35L±GKBSKA
Tire size: P245/70R16
Tire size: P265/70R16 and P265/65R17
Tire size: P265/65R17 (Air suspension models)
0°05' ± 0°09' (0.09° ± 0.15°, 1.19 ± 2 mm (0.05 ± 0.08 in.)
0°05' ± 0°09' (0.09° ± 0.15°, 1.29 ± 2 mm (0.05 ± 0.08 in.)
0°05' ± 0°09' (0.09° ± 0.15°, 1.28 ± 2 mm (0.05 ± 0.08 in.)
UCK35L±GKBLKA0°05' ± 0°09' (0.08° ± 0.15°, 1.15 ± 2 mm (0.05 ± 0.08 in.)
UCK45L±GKBSKA
Tire size: P265/70R16 (Air suspension models)0°05' ± 0°09' (0.08° ± 0.15°, 1.08 ± 2 mm (0.04 ± 0.08 in.)
0°05' ± 0°09' (0.08° ± 0.15°, 1.07 ± 2 mm (0.04 ± 0.08 in.)
UCK45L±GKBLKA0°04' ± 0°09' (0.07° ± 0.15°, 0.99 ± 2 mm (0.04 ± 0.08 in.)
UCK35L±GKSSKAInside wheel
Outside wheel: Reference
Outside wheel (Air suspension models): Reference-35°24' (-35.40°)
32°08' (32.13°)
31°54' (31.90°)
UCK35L±GKSLKAInside wheel
Outside wheel: Reference-35°22' (-35.36°)
32°07' (32.12°)
UCK45L±GKSSKAInside wheel
Outside wheel: Reference-35°37' (-35.61°)
32°17' (32.28°)
UCK45L±GKSLKAInside wheel
Outside wheel: Reference-35°35' (-35.59°)
32°16' (32.26°)
Front drive shaftFront drive shaft length523.5 ± 2.0 mm (20.610 ± 0.079 in.)
Upper ball joint turning torque0.7 ± 4.4 N´m (7 ± 45 kgf´cm, 6 ± 39 in.´lbf)
Ft iLower ball joint excessive play Maximum0.5 mm (0.020 in.)Front suspensionLower ball joint turning torque1.0 ± 6.5 N´m (10 ± 66 kgf´cm, 9 ± 56 in.´lbf)
Stabilizer bar link ball joint turning toque0.05 ± 2.0 N´m (0.5 ± 20 kgf´cm, 0.4 ± 17 in.´lbf)

DIDJT±01
F19148
Combination Meter
Tire Pressure
Warning Lamp DI±796
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
990 Author: Date:
2005 SEQUOIA (RM1146U)
TIRE PRESSURE WARNING SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77
1. TIRE PRESSURE WARNING SYSTEM PRECAUTION
(a) When the tire pressure warning lamp comes on, immedi-
ately check the tire pressure of the tire and adjust it to the
specified pressure. (The tire pressure warning lamp
comes on if there is an open in the tire pressure warning
lamp circuit.)
NOTICE:
Check the spare tire as well since this system monitors
pressure of all tires, including the spare.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
(b) When the tire pressure warning lamp blinks, there is a
malfunction in the system. Check for DTCs.
(c) It is necessary to register the transmitter ID in the tire pres-
sure monitor ECU when replacing the tire pressure moni-
tor valve sub±assy and/or tire pressure monitor ECU (see
page DI±805).
(d) When replacing the tire pressure monitor ECU.
(1) Using the DATA LIST, read the transmitter IDs regis-
tered in the ECU and make a note of them before
removing the tire pressure monitor ECU.
(2) Register the transmitter IDs after installing a new
tire pressure monitor ECU.
(e) When replacing the tire pressure monitor valve sub±assy.
(1) Make a note of the 7 digit number (transmitter ID)
written on the tire pressure monitor valve sub±assy
when replacing the tire pressure monitor valve sub±
assy. Register the transmitter IDs in the tire pres-
sure monitor ECU after replacing the tire pressure
monitor valve sub±assy and installing the tires and
wheels on the vehicle.

DIDJY±01
Inspector 's
Name:
Customer 's Name
Date Vehicle
Brought InProduction DateVIN
Licence Plate No.
Odometer Reading/ /
/ /
Date of First Occurrence
Frequency of Problem Occurrence/ /
Continuous Intermittent ( times a day)
In spite of abnormal low tire pressure, the warning lamp does not
come on.
The warning lamp was lit and the tire was filled up with air, but
the warning lamp does not go off.
Remains ONDoes not come on
Check ItemTire Pressure
Warning LampNormal
Malfunction Code (Code )
Symptomskm
miles
Tire Pressure Warning System Check Sheet
Tire Pressure
Warning Lamp
Abnormal
TireTire Pressure
FR ( ) FL ( ) RR ( ) RL ( )
Tire Size
Tire Type
Tire Wear Condition
History of changing tires or wheels
When ( )
History of rotating tires FR ( ) FL ( ) RR ( ) RL ( )
FR ( ) FL ( ) RR ( ) RL ( )
FR ( ) FL ( ) RR ( ) RL ( )
When ( )
DI±804
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
998 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMER PROBLEM ANALYSIS CHECK

DIDJZ±01
F19326
F19327
F19328
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±805
999 Author: Date:
2005 SEQUOIA (RM1146U)
REGISTRATION
1. IN CASE OF TIRE PRESSURE MONITOR ECU REPLACEMENT
(a) Read ID stored in the old ECU using the hand±held tester.
2. IN CASE OF TIRE PRESSURE MONITOR VALVE SUB±ASSY AND/OR TIRE PRESSURE MON-
ITOR ECU REPLACEMENT
(a) Read ID written on the tire pressure monitor valve.
3. REGISTER TRANSMITTER ID
NOTICE:
It is necessary to register the transmitter ID in the tire pressure monitor ECU when replacing the tire
pressure monitor valve sub±assy and/or tire pressure monitor ECU.
(a) Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
(b) Connect the hand±held tester to DLC3.
(c) Turn the ignition switch to the ON position.
(d) Read and write down the ID (ID1 to ID5) by using the
DATA LIST.
(e) Select the REGIST TIRE following the hand±held tester
screen.
(UTILITY ± REGIST TIRE)
(f) Input the ID (ID1 to ID5) using the hand±held tester and
transmit it to the tire pressure monitor ECU.
(g) Set the ID transmission condition to ºSUCCEEDEDº.
HINT:
If the operations of steps (d) to (f) do not complete within 5 min.,
the mode will return to normal operation mode.

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±807
1001 Author: Date:
2005 SEQUOIA (RM1146U)
4. CONFIRMATION OF TRANSMITTER ID REGISTRATION
(a) Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
(b) Connect the hand±held tester to DLC3.
(c) Turn the ignition switch to the ON position.
(d) Select ºSIGNAL CHECKº mode on the hand±held tester (see page DI±810).
(e) Forcibly transmit the transmitter IDs for all wheels.
(1) When rapidly reducing the pressure, remove the valve core (above 20 kPa/15 sec.).
HINT:

The transmitter ID can be transmitted by rapidly reducing the tire air pressure.

When rapidly reducing the pressure, remove the valve core (above 20 kPa/15 secs.).
(2) Perform the steps mentioned above to all tires including the spare tire.
(f) Check that test mode DTCs C2181/81, C2182/82, C2183/83, C2184/84 and C2185/85 are all erased.
HINT:

The transmitter ID registration is complete when the test mode DTCs are erased.

If they haven't been erased, reset the tire pressure to the specified value and rotate the tire 90 to 270
degrees. Then forcibly transmit the transmitter IDs of all wheels. If they are still output, register the
transmitter IDs.
(g) Set the tire pressure of all wheels to the specified value.