2001 TOYOTA SEQUOIA Service Repair Manual

trip computer mileage wheel bolts alarm battery fuse diagram

Load previous 8 pages

Page 1313 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual 12345678
9 10111213141516
F19737
DLC3:
D6CANH
CANL
BAT
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
DI±1111
1305 Author: Date:
2005 SEQUOIA (RM1146U)
7 Check CAN bus line for short to +B (Suspension co

Page 1314 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual 12345678
9 10111213141516
F19737
DLC3:
D6CANH
CANL
BAT
DI±1112
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
1306 Author: Date:
2005 SEQUOIA (RM1146U)
9 Check CAN bus line for short to +B (ECM main bus

Page 1315 of 4323

Page 1316 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual F19702
ECM
CANH
CANL
ENG+
ENG± CANH
CANL
CANH
CANL D6 DLC3
Translate ECU
Suspension Control ECU33
E5
34
E5L
W1
J53
2
J53Junction Connector
1
J54
2
J54 B
W 6
14
14
T5
16
T51
J55
2
J55 R
W
29
S25
28
S2

Page 1317 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual F19749
CAN J/C ºAº Side (w/ Earth Terminal)
Wire Harness View:
J56
G
WEarth Terminal
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
DI±1115
1309 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDUR

Page 1318 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DI±1116
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
1310 Author: Date:
2005 SEQUOIA (RM1146U)
3 Replace translate ECU.
PREPARATION:
(a) Replace the translate ECU.
HINT:
Perform the inspection using pa

Page 1319 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual F16805
Suspension Control ECU
Wire Harness View:
CANH
CANLS25
± DIAGNOSTICSCAN COMMUNICATION SYSTEM
DI±1117
1311 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check for an open in one side of the CAN

Page 1320 of 4323

TOYOTA SEQUOIA 2001 Service Repair Manual DICY7±02
DI±1118
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1312 Author: Date:
2005 SEQUOIA (RM1146U)
SUPPLEMENTAL RESTRAINT SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, i

DICY7±02
DI±1118
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1312 Author: Date:
2005 SEQUOIA (RM1146U)
SUPPLEMENTAL RESTRAINT SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77
1. HANDLING PRECAUTIONS FOR AIRBAG SENSOR
HINT:
In this section, the airbag sensor assembly, front airbag sensor LH, front airbag sensor RH, side airbag sen-
sor assembly LH, side airbag sensor assembly RH, curtain shield airbag sensor assembly LH, curtain shield
airbag sensor assembly RH and seat position airbag sensor assembly are collectively referred to as the air-
bag sensor.
(a) Before starting the following operations, wait at least 90 seconds after disconnecting the negative (±)
terminal of the battery:
(1) Replacement of the airbag sensor.
(2) Adjustment of the front/rear doors of the vehicle equipped with the side airbag and curtain shield
airbag (fitting adjustment).
(b) When connecting or disconnecting the airbag sensor connector, ensure that all of the sensors are
installed in the vehicle.
(c) Do not use an airbag sensor which has been dropped during the operation or transportation.
(d) Do not disassemble the airbag sensor.
2. INSPECTION PROCEDURE FOR VEHICLE INVOLVED IN ACCIDENT
(a) When the airbag has not deployed, confirm the DTC by checking the SRS warning light. If there is any
malfunction in the SRS airbag system, perform troubleshooting.
(b) When any of the airbags have deployed, replace the airbag sensor and check the installation condition.
(c) Perform the zero point calibration and sensitivity check under the condition is listed below (see page
DI±1128).
The occupant classification ECU is replaced.
Accessories (seatback tray, seat cover, etc.) are installed.
The passenger seat removed from the vehicle.
The passenger airbag ON/OFF indicator (ºOFFº) comes on when the passenger seat is not occu-
pied.
The vehicle is brought to the workshop for repair due to an accident or a collision.
NOTICE:
When an accident vehicle is brought into the workshop for repair, check the flatness of the body side
that is installed on the passenger seat. If the flatness is not within ± 3.0 mm (0.118 in.), repair it to
the specified range (within ± 3.0 mm (0.118 in.)).

Load next 8 pages

Page: < prev 1-10 ... 1281-1288 1289-1296 1297-1304 1305-1312 1313-1320 1321-1328 1329-1336 1337-1344 1345-1352 ... 4328 next >

trunk release diagnostic menu spark plugs replace suspension driver seat adjustment hood release