Page 2993 of 4323
PR01G±06
F19802Non±reusable part
N´m (kgf´cm, ft´lbf) : Specified torqueSpider BearingSnap Ring
Spider
Sleeve Yoke
Spider Propeller Shaft
Spider Bearing
Snap Ring Flange Yoke
88 (897, 65)
.
PR±2
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY (2WD)
2985 Author: Date:
2005 SEQUOIA (RM1146U)
PROPELLER SHAFT ASSEMBLY (2WD)
COMPONENTS
Page 2994 of 4323
PR01H±04
F19347Matchmarks
R04164
SST
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY (2WD)
PR±3
2986 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
REMOVE PROPELLER SHAFT
(a) Place matchmarks on the differential and propeller shaft
flanges.
(b) Remove the 4 nuts and washers.
(c) Pull out the propeller shaft yoke from the transmission.
(d) Insert SST in the transmission to prevent oil leakage.
SST 09325±40010
Page 2995 of 4323
PR07K±02
Z04240
Z04241
PR±4
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY (2WD)
2987 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
NOTICE:
Be careful not to grip the propeller shaft tube too tightly in
a vise as this will cause deformation.
1. INSPECT PROPELLER SHAFT AND INTERMEDIATE
SHAFT FOR DAMAGE OR RUNOUT
Using a dial indicator, check the runout of each shaft.
Maximum runout: 0.8 mm (0.031 in.)
If shaft runout is greater than the maximum, replace the shaft.
2. INSPECT SPIDER BEARING
(a) Inspect the spider bearing for wear or damage.
(b) Using a dial indicator, check the spider bearing axial play
by turning the yoke of flange while holding the shaft tight-
ly.
Maximum bearing axial play: 0.05 mm (0.0020 in.)
If the spider bearing axial play exceeds the maximum, replace
the spider bearing (See page PR±10).
Page 2996 of 4323
PR07L±02
F19347Matchmarks
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY (2WD)
PR±5
2988 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
INSTALL PROPELLER SHAFT
(a) Remove the SST from the transmission.
SST 09325±40010
(b) Insert the yoke into the transmission.
(c) Align the matchmarks on the flanges and connect the
flanges with the washers and nuts.
(d) Torque the 4 nuts.
Torque: 88 N´m (897 kgf´cm, 65 ft´lbf)
Page 2997 of 4323
PR01M±05
F19351
Front propeller shaft:
Rear propeller shaft:
N´m ( kgf´cm, ft´lbf )
Non±reusable part: Specified torque
74 (750, 54)
88 (897, 65)
Flange Yoke
Flange Yoke
Snap Ring
Spider Bearing
Spider
Snap Ring Spider Bearing SpiderFront Propeller Shaft
88 (897, 65)
Flange Yoke
Snap Ring
Spider Bearing
Spider
88 (897, 65)
Rear Propeller Shaft
Snap Ring
Spider Bearing
Spider
Flange Yoke
Grease Fitting
Grease Fitting Sleeve Yoke
PR±6
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY (4WD)
2989 Author: Date:
2005 SEQUOIA (RM1146U)
PROPELLER SHAFT ASSEMBLY (4WD)
COMPONENTS
Page 2998 of 4323
PR05N±04
Z15303Matchmarks
Q07228
Matchmarks
F13575
Matchmarks
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY (4WD)
PR±7
2990 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE FRONT PROPELLER SHAFT
(a) Place matchmarks on the differential and propeller shaft
flange.
(b) Remove the 4 nuts, washers and bolts, and disconnect
the propeller shaft from the differential.
(c) Suspend the front side of the propeller shaft.
(d) Place matchmarks on the transfer and propeller shaft
flanges.
(e) Remove the 4 nuts and washers.
(f) Remove the propeller shaft from the transfer.
2. REMOVE REAR PROPELLER SHAFT
(a) Place matchmarks on the transfer and propeller shaft
flanges.
(b) Remove the 4 nuts and washers, and disconnect the pro-
peller shaft from the transfer.
(c) Suspend the front side of the propeller shaft.
(d) Place matchmarks on the differential and propeller shaft
flanges.
(e) Remove the 4 nuts, washers and bolts.
(f) Remove the propeller shaft from the differential.
Page 2999 of 4323
PR07M±02
Z04240
Z04241
PR±8
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY (4WD)
2991 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
NOTICE:
Be careful not to grip the propeller shaft tube too tightly in
a vise as this will cause deformation.
1. INSPECT PROPELLER SHAFT AND INTERMEDIATE
SHAFT FOR DAMAGE OR RUNOUT
Using a dial indicator, check the runout of each shaft.
Maximum runout: 0.8 mm (0.031 in.)
If shaft runout is greater than the maximum, replace the shaft.
2. INSPECT SPIDER BEARING
(a) Inspect the spider bearing for wear or damage.
(b) Using a dial indicator, check the spider bearing axial play
by turning the yoke of flange while holding the shaft tight-
ly.
Maximum bearing axial play: 0.05 mm (0.0020 in.)
If the spider bearing axial play exceeds the maximum, replace
the spider bearing (See page PR±10).
Page 3000 of 4323

PR07N±02
Z15303
Matchmarks
F13575
Matchmarks
Q07228
Matchmarks
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY (4WD)
PR±9
2992 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. INSTALL FRONT PROPELLER SHAFT
(a) Align the matchmarks on the propeller shaft flanges and
differential, and connect the flanges with the 4 bolts,
washers and nuts.
(b) Torque the 4 bolts.
Torque: 74 N´m (750 kgf´cm, 54 ft´lbf)
(c) Align the matchmarks on the propeller shaft flanges and
transfer, and connect the flanges with the 4 washers and
nuts.
(d) Torque the 4 nuts.
Torque: 88 N´m (897 kgf´cm, 65 ft´lbf)
2. INSTALL REAR PROPELLER SHAFT
(a) Align the matchmarks on the propeller shaft flanges and
differential, and connect the flanges with the 4 bolts,
washers and nuts.
(b) Torque the 4 bolts.
Torque: 88 N´m (897 kgf´cm, 65 ft´lbf)
(c) Align the matchmarks on the propeller shaft flanges and
transfer, and connect the flanges with the 4 washers and
nuts.
(d) Torque the 4 nuts.
Torque: 88 N´m (897 kgf´cm, 65 ft´lbf)