Page 3689 of 4323
H24319
H24335
H24336
H24395
H24342
BO±128
± BODYFRONT SEAT (Manual Adjuster Type)
3681 Author: Date:
2005 SEQUOIA (RM1146U)
9. REMOVE SEATBACK COVER
(a) Turn up the seatback cover and remove the hog rings.
(b) Remove the 2 headrest supports.
(c) Remove the seatback cover from the seatback pad.
10. REMOVE SEAT CUSHION COVER AND PAD
(a) Remove the clip.
(b) Perform the same procedure on the other side.
(c) Remove the hog rings from the seat cushion cover.
(d) Unlatch the seat cushion cover hooks, then remove the
seat cushion cover with seat cushion pad.
11. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat
cushion pad.
12. REMOVE RH AND LH UPPER RECLINING ADJUSTER
INSIDE COVERS
(a) Remove the screw and LH upper reclining adjuster inside
cover.
(b) Perform the same procedure on the other side.
Page 3690 of 4323
H24343
H24341
± BODYFRONT SEAT (Manual Adjuster Type)
BO±129
3682 Author: Date:
2005 SEQUOIA (RM1146U)
13. REMOVE RH AND LH LOWER RECLINING ADJUSTER
INSIDE COVERS
(a) Remove the screw and LH lower reclining adjuster inside
cover.
(b) Perform the same procedure on the other side.
14. REMOVE RH AND LH SEAT CUSHION LOWER
SHIELDS
(a) Using a screwdriver, disengage the claw and remove the
LH seat cushion lower shield.
HINT:
Tape the screwdriver tip before use.
(b) Perform the same procedure on the other side.
15. Driver 's seat:
REMOVE SEAT POSITION SENSOR
(See page RS±104)
Page 3691 of 4323

BO4SE±01
H24343
H24342
H24395
BO±130
± BODYFRONT SEAT (Manual Adjuster Type)
3683 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:
The procedures listed below are for the LH side.
A bolt without a torque specification is shown in the stan-
dard bolt chart (see page SS±2).
1. Driver 's seat:
INSTALL SEAT POSITION SENSOR
(SEE PAGE RS±108)
2. INSTALL RH AND LH SEAT CUSHION LOWER
SHIELDS
3. INSTALL RH AND LH LOWER RECLINING ADJUSTER
INSIDE COVERS
(a) Install the LH lower reclining adjuster inside cover with the
screw.
(b) Perform the same procedure on the other side.
4. INSTALL RH AND LH UPPER RECLINING ADJUSTER
INSIDE COVERS
(a) Install the LH upper reclining adjuster inside cover with
the screw.
(b) Perform the same procedure on the other side.
5. INSTALL SEAT CUSHION COVER
Install the seat cushion cover to the seat cushion pad with the
hog rings.
HINT:
When installing the hog rings, take as much care as possible to
prevent wrinkles.
6. INSTALL SEAT CUSHION COVER AND PAD
(a) Install the seat cushion cover with seat cushion pad, and
latch the seat cushion cover hooks.
Page 3692 of 4323
H24336
H24335
H24319
H24339Hog Ring
H24338Hog Ring
± BODYFRONT SEAT (Manual Adjuster Type)
BO±131
3684 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Install the hog rings to the seat cushion cover.
(c) Install the clip.
(d) Perform the same procedure on the other side.
7. INSTALL SEATBACK COVER
(a) Install the seatback cover to the seatback pad.
(b) Install the 2 headrest supports.
(c) Turn up the seatback cover and install the hog rings.
8. INSTALL SEATBACK COVER AND PAD
(a) Install the seatback cover and pad to the seat frame as-
sembly.
(b) Install the hog rings to the seat frame assembly.
(c) Install the hog rings to the seat frame assembly.
Page 3693 of 4323
H24861
H24337
H24316
H24334ClawsClip BO±132
± BODYFRONT SEAT (Manual Adjuster Type)
3685 Author: Date:
2005 SEQUOIA (RM1146U)
(d) w/ Side airbag:
Connect the seatback cover bracket to the seat frame as-
sembly with the nut.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
(e) Close the fastener.
(f) Install the hog rings to the seat frame assembly.
9. INSTALL ARMREST ASSEMBLY
(a) Install the spacer to the armrest assembly.
(b) Install the armrest assembly, armrest lock plate and arm-
rest spacer with the bolt.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
HINT:
Install the armrest lock plate as shown in the illustration.
(c) Install the armrest cap.
10. INSTALL FRONT SEAT INNER BELT.
(a) Install the front seat inner belt with the nut.
Torque: 42 N´m (430 kgf´cm, 32 ft´lbf)
(b) Connect the connectors and wire harness clamps.
11. INSTALL SEAT CUSHION INNER SHIELD
Install the seat cushion inner shield with the screw.
Page 3694 of 4323
H24333
H24331ClawsClip
± BODYFRONT SEAT (Manual Adjuster Type)
BO±133
3686 Author: Date:
2005 SEQUOIA (RM1146U)
12. INSTALL VERTICAL ADJUSTER HANDLE
(a) Install the vertical adjuster handle with the 2 screws.
(b) Install the vertical adjuster handle cap.
13. INSTALL RECLINING ADJUSTER RELEASE HANDLE
14. INSTALL SEAT CUSHION OUTER SHIELD
Install the seat cushion outer shield with the screw.
15. INSTALL HEADREST
Page 3695 of 4323

BO4SF±01
BO±134
± BODYFRONT SEAT (Manual Adjuster Type)
3687 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
The procedures listed below are for the LH side.
1. INSTALL FRONT SEAT
(a) Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the vehicle body.
(b) w/ Side airbag:
Connect the airbag connector.
(c) Connect the connectors.
(d) Slide the front seat to the rearmost position.
(e) Tighten the bolts on the front side temporarily, starting from the bolt on the inner side.
(f) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
(g) Slide the front seat to the foremost position.
(h) Tighten the bolts on the rear side temporarily, starting from the bolt on the inner side.
(i) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
2. INSTALL SEAT TRACK COVERS
3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4. Passenger 's seat:
PERFORM PASSENGER OCCUPANT CLASSIFICATION SYSTEM ZERO POINT CALIBRATION
(See page DI±1128)
5. PERFORM INITIALIZATION (See page IN±20)
Some systems need initialization when disconnecting the cable from the negative battery terminal.
Page 3696 of 4323
BO4R8±02
H24385
Headrest
Headrest
Support
Seatback CoverSeatback Pad
Seatback Frame
Seat Cushion
Cover
Seat Cushion Pad
Seat Cushion
Frame
Fold Seat
Stopper Band LH Rear Seat Lock
Seat Cushion
Under cover RH Rear Seat
Reclining Adjuster
Cushion Rear No. 1 Seat
Inner Belt
No. 1 Rear Seat
Reclining Cover
RHReclining Adjuster
Release Handle
LH Rear Seat
Reclining Adjuster
No. 1 Rear Seat
Reclining Cover LH
43 (440, 32)
Reclining
Connecting Pipe
42 (430, 31)
37 (380, 27)
37 (380, 27)
N´m (kgf´cm, ft´lbf) : Specified torque
43 (440, 32)
43 (440, 32)
43 (440, 32)
Seat Leg Cover LH Seat Leg
Cover RH Hog Ring
Non±reusable part
Hog Ring
Fold Seat Lock Control Cable No. 1
Rear Seat Cushion
Hinge RH
Rear Seat Cushion
Hinge LH
43 (440, 32)
64 (653, 47)
RH Rear Seat Lock
± BODYREAR NO.1 SEAT (Separate Type)
BO±135
3688 Author: Date:
2005 SEQUOIA (RM1146U)
REAR NO.1 SEAT (Separate Type)
COMPONENTS
HINT:
The procedures listed below are for the RH side.